summaryrefslogtreecommitdiff
path: root/target/linux/apm821xx/nand
Commit message (Collapse)AuthorAgeFilesLines
* apm821xx: redo WAN green and yellow LEDsChristian Lamparter2016-11-081-0/+2
| | | | | | | | | Because the WAN port is handled by the internal AR8327N switch, the device should use swconfig_leds trigger to handle the link activity of the WAN LED. This has the added bonus that the WAN LED will now go dark if there's no ethernet cable connected to the WAN port. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-1/+1
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* apm821xx: backport generic HDD led-triggers for WNDR4700 and MBLChristian Lamparter2016-09-081-0/+1
| | | | | | | This patch backports the new generic HDD/SDD led-trigger from 4.8-rc1. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add missing default profiles for subtargetsFelix Fietkau2016-07-221-0/+22
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* apm821xx: add support for the Netgear Centria N900 WNDR4700/WNDR4720Christian Lamparter2016-07-221-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netgear Centria N900 WNDR4700/WNDR4720 hardware highlights: CPU: AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz) Security support, Boot ROM Location NAND wo/ECC 2k page (8 bits) 32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory Board: AMCC APM82181 Evaluation Board, PCIE0/SATA1, 1*USB OTG DRAM: 256 MB (ECC not enabled, 500 Mb/s, 32-bit, CL3) NAND: 128 MiB (SLC, erase size: 128 KiB, page size: 2048, OOB size: 64) ETH: Atheros AR8327N Gigabit Switch (4 x LAN, 1 x WAN) USB: 2 x 3.0 (Renesas uPD720202K8-711-BAA-A, firmware not included) SATA: 1 x SATA-II 3.5" Hard Drive Bay for HDDs (DesignWare SATA). WLAN1: Atheros AR9380 5GHz 802.11an 3:3x3 WLAN2: Atheros AR9581 2.4GHz 802.11bgn 3:3x3 SDCARD: GL827L SD/MMC/MS Flash Card Reader (on internal dwc2 USB 2.0 host) I2C: GMT G781 (i2c-0 @ 0x4d - lm90 compatible temperature sensor) TC654 (i2c-0 @ 0x1b - Dual PWM fan Speed controller) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! INFO: Since this device only has a NAND chip. I opted for going with root.squashfs in a UBI volume. There's no squashfs/jffs2 image. This target produces three images. a. netgear factory image This image can be used to flash the Netgear WNDR4700 via the firmware recovery mechanism and the web admin site. The bootloader can be instructed to do a firmware recovery via the # fw_recovery command. It will start a tftp server and listen on 192.168.1.1 (the ipaddr variable in u-boot) for incoming, binary tftp clients. The firmware recovery mechanism is also started if any of the flash content which contains the kernel, device-tree definitions or the (fake)rootfs fails to verify or load. b. sysupgrade.tar image for sysupgrade An sysupgrade will replace the entire current LEDE installation with a newer version. This does include the kernel and the ubi rootfs partition. The configuration can be carried over automatically as well if desired. simply copy the sysupgrade.tar to a the WNDR4700 running LEDE and run: root@lede:~# sysupgrade sysupgrade.tar and let it reboot. Note: The devicetree flash area is NOT updated. Until the devicetree definition is stable, this can lead to all sorts of hardware detection problems! So make sure, if you experience issues: try the fw_recovery. If you are unsure whenever this affects you: test if you can reproduce your issue with the initramfs method. As it will always have up-to-date device-tree definitions. c. initramfs image for TFTP (for development and testing) To use the initramfs method, follow the following steps: 1) Move the "lede-apm821xx-netgear-WNDR4700-initramfs-kernel.bin" file to to the root directory of your TFTP server. 2) rename it to wndr4700.bin 3) On the WNDR4700 - Hit Enter during u-boot and insert: # tftp 400000 wndr4700.bin; run addtty; bootm 400000 - This will boot the LEDE image. Note: The default tftp server is 192.168.1.7, if you want to change it: # setenv serverip 192.168.8.7; Note2: The default address for the WNDR4700 is 192.168.1.1: # setenv ipaddr 192.168.8.8; Note: Connect you tftp server on the last LAN port (not the WAN) Note: The firmware for the USB 3.0 Host chip is not included anymore. Therefore the two USB 3.0 ports will not work without the uPD7070x-firmware package installed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Cisco Meraki MR24Chris Blake2016-07-222-0/+16
This patch adds support for the Cisco Meraki MR24 Access point to the apm821xx target. Board: MR24 - Meraki MR24 Cloud Managed Access Point CPU: APM82181 SoC 800 MHz (PLB=200 OPB=100 EBC=100) Flash size: 32MiB RAM Size: 128MiB Wireless: Atheros AR9380 5.0GHz + Atheros AR9380 2.4GHz Ethernet ports: 1x Gigabit Atheros AR8035 WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! For flashing instructions, visit: <https://github.com/riptidewave93/Openwrt-MR24/blob/master/README.md#flashing> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>