summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx/files
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: add support for D-Link DAP-2695 rev. A1Stijn Tintel2016-10-274-0/+202
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* ar71xx: add support for TP-Link WR802N v1Julius Schulz-Zander2016-10-264-0/+108
| | | | | | | This patch adds support solely for version 1 of the TP-Link WR802N. It is based on Rick Pannen's patch posted on the OpenWrt devel list. Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
* ar71xx: add mac partition to the MR12/MR16Chris Blake2016-10-262-19/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space after u-boot-env is used to store the boards Mac address. Sadly as this was removed on any device already on OpenWRT/LEDE, moving forward a new, 64k partition named "mac" will be used to store the mac address for the device (which is the minimum size). This allows users to properly set the correct MAC, without editing the ART partition (which holds the same MAC for all devices). The reason the space is taken from kernel instead of rootfs is currently kernels are only 1.3MB, so that way we can leave the current rootfs space alone for users who fully utilize the available storage space. Once this partition is added to a device, you can set your MAC doing the following: mtd erase mac echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5 sync && reboot Where 00:18:0a:33:44:55 is your MAC address. This was tested, and confirmed working on both the MR12 and MR16. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: Add support to DomyWifi DW33DJing Lin2016-10-254-0/+205
| | | | Signed-off-by: Jing Lin <mumuqz@163.com>
* ar71xx: Add support to TP-Link EAP120Henryk Heisig2016-10-184-0/+137
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for the Airtight C-60Christian Lamparter2016-10-154-0/+214
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Airtight C-60. SOC: Atheros AR9344 rev 2 (CPU:560.000MHz) RAM: 128 MiB NOR: MX25L3205D 4MiB NAND: ST Micro NAND 32MiB 3,3V 8-bit SW-NET: AR8327N (2 Ports) WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC) WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip The switch is setup for an accesspoint: LAN1: (gigabit) is the wan-port. LAN2: (fast ethernet) is bridged with the br-lan. Flashing Guide (via initramfs): 1. Connect a PC to the serial port of the C-60. power up the C-60. Enter u-boot command prompt: #> nand erase #> setenv bootcmd "bootm 0x9f060000" #> saveenv #> setenv ipaddr 192.168.1.1 #> setenv netmask 255.255.255.0 #> setenv serverip 192.168.1.100 #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin #> tftpboot #> bootm 2. Wait for the C-60 to boot LEDE. On the root prompt. Enter: # ubiformat /dev/mtd4 # ubiattach -p /dev/mtd4 3. After that copy the sysupgrade.tar onto the router and run: # sysupgrade sysupgrade.tar to flash the image. Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided a C-60 unit and he helped with debugging the switch, LEDs and platfrom support. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: add kernel support for D-Link DIR-869 A1Matthias Schiffer2016-10-114-0/+190
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: comsetic cleanups in files/arch/mips/ath79/{Makefile,machtypes.h}Piotr Dymacz2016-10-042-422/+422
| | | | | | Keep everything in alphabetical order and aligned in columns. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix LED names for GL Innovations boardsPiotr Dymacz2016-10-045-18/+18
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker GatewayChris Blake2016-09-274-0/+178
| | | | | | | | | This patch adds support for Cisco's Z1. Detailed instructions for the flashing the device can be found in the OpenWrt wiki: <https://wiki.openwrt.org/toh/meraki/z1> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: fix ethernet driver fast reset issue causing tx timeoutsFelix Fietkau2016-09-031-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: disable flow control to the built-in switch on AR934xFelix Fietkau2016-08-251-1/+0
| | | | | | | It apparently causes a regression on some devices if the ethernet cable is plugged in while booting. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for Zbtlink ZBT-WE1526Piotr Dymacz2016-08-184-0/+165
| | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 650/400/200 MHz (CPU/DDR/AHB) - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - two external, non-detachable antennas - 8x LED, 1x button - UART header (pinout: VCC, RX, TX, GND) Flash instruction: Use sysupgrade in vendor firmare which is based on OpenWrt. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for gl-mifiZhao Gang2016-07-244-0/+126
| | | | | | | This add initial support for gl-mifi. Product page: http://www.gl-inet.com/mifi/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add support for gl-ar300mZhao Gang2016-07-204-0/+194
| | | | | | | This add initial support for gl-ar300m router. Product page: http://www.gl-inet.com/ar300m/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add software transmit timestamp supportStephen Walker2016-07-152-0/+3
| | | | | | Add software transmit timestamp and ethtool (-T) timestamp support Signed-off-by: Stephen Walker <stephendwalker+github@gmail.com>
* ar71xx: add support for jjPlus JWAP230Piotr Dymacz2016-07-134-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 2x 10/100/1000 Mbps Ethernet - 128 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm - 3x MMCX connectors - power input: 802.3at PoE or wide range DC (36-57 V) - optional 802.3af PSE - 1x mini-PCIe connector with PCIe, USB buses and SIM slot - 1x mini-PCIe connector with PCIe bus - 1x USB type-A connector - 6x LED, 1x button (hardware reset) - RS232 (MAX3223) and (E)JTAG headers Default configuration: - WAN on eth1 (RJ45 near LEDs with PoE input) - LAN on eth0 (RJ45 near DC jack) - left top LED set to be status LED - all LEDs configurable form user space Flash instruction (do it under U-Boot, using RS232): 1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Wallys DR531Piotr Dymacz2016-07-134-0/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 550/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm - 2x MMCX connectors - mini-PCIe connector with PCIe/USB buses and SIM slot - 7x LED, 1x button, 1x optional buzzer - UART, (E)JTAG and LED headers Default configuration: - WAN on eth1 (RJ45 near DC jack) - LAN on eth0 (RJ45 near button) - S4 LED set to be status LED - all LEDs configurable form user space - button configured for reset Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: spi-rb4xx fix.Sergey Sergeev2016-07-021-1/+1
| | | | | | | | In new kernels we should use clk_prepare_enable instead of clk_enable since clk_enable does not make proper initialization that leads to rise WARN_ON messages and not working spi bus on the device. Signed-off-by: Sergey Sergeev <adron@yapic.net>
* ar71xx: prevent spurious ethernet resets from dma hang check false positivesFelix Fietkau2016-07-022-6/+12
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: disable pdata->use_flow_control for QCA9558Felix Fietkau2016-06-271-1/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: rename ethernet pdata->builtin_switch to use_flow_controlFelix Fietkau2016-06-273-8/+8
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "ar71xx: prevent spurious ethernet resets from dma hang check false ↵Felix Fietkau2016-06-262-6/+5
| | | | | | positives" This reverts commit 3d58d7f053eae83b59baf5c8b8a58da78653f605.
* ar71xx: prevent spurious ethernet resets from dma hang check false positivesFelix Fietkau2016-06-262-5/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: enable flow control for ethernet MACs with built-in switchFelix Fietkau2016-06-263-1/+11
| | | | | | | | Should fix LAN speed issues on some devices. This is an updated version of the previously reverted commit with the same name. It improves the check for MACs connected to a built-in switch Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "ar71xx/cpe510: use second wifi calibration table"Alexander Couzens2016-06-161-1/+1
| | | | | | | | Using the high power table can damage the device in some cases. This reverts commit bf27ac019c137e7baf90ca6ef0e40945ae871797. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* Revert "ar71xx: enable flow control for ethernet MACs with built-in switch"Felix Fietkau2016-06-141-9/+1
| | | | | | | | This reverts commit 1beb5bec6453abb220c5be4ddb9e6dc02d08d735. It was found to cause the WAN port to fail on some AR934x devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: mach-ubnt-xm.c convert patches to mach fileArne Zachlod2016-06-131-0/+700
| | | | Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ar71xx: enable flow control for ethernet MACs with built-in switchFelix Fietkau2016-06-131-1/+9
| | | | | | Should fix LAN speed issues on some devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for OpenEmbed SOM9331Allan Nick Pedrana2016-06-074-0/+137
| | | | | | | | This patch adds the target profile SOM9331 and configures hardware functionality for the 3x Eth Ports & corresponding LED's, the USB Host, the USART to USB bridge and the System LED. Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
* treewide: replace nbd@openwrt.org with nbd@nbd.nameFelix Fietkau2016-06-076-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add WRTnode2Q supportKeLei Liang2016-06-064-0/+138
| | | | Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
* ar71xx: Fix TL-WR841N v11 LEDs, use separate machineStijn Segers2016-05-312-1/+71
| | | | Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx/cpe510: use second wifi calibration tableAlexander Couzens2016-05-231-1/+1
| | | | | | | The cpe510 has two calibration tables. The first calibration table requires to modify ath9k driver to work (patched tx gain table). Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510Alexander Couzens2016-05-232-6/+25
| | | | | | | Split profile into 2GHz and 5GHz. The 5GHz devices are quite "special". The 2 GHz works perfect. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: add kernel support for the OpenMesh MR1750v2Sven Eckelmann2016-05-232-0/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add kernel support for the OpenMesh OM2P-HSv3Sven Eckelmann2016-05-232-0/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx/cpe510: enable LNA for CPE210/220/510/520Alexander Couzens2016-05-201-0/+6
| | | | | | | The LNA improves the rx path. Within a simple test setup it improved the signal from -60dbm to -40dbm. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: fix DDR write buffer flushing issues with 4.4Felix Fietkau2016-05-151-73/+16
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-LINK TL-WR842N/ND v3Cezary Jackiewicz2016-05-143-8/+105
| | | | | | | | | | | - CPU QCA9531-BL3A - RAM: 64MB - flash: 16MB - USB AP143 platform, similar to tl-wr841n v10/v11, but with USB Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ar71xx: add proper support for Archer-C7 V2John Crispin2016-05-142-4/+41
| | | | | | This has minor differences to the V1 Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Fix TP-LINK Archer-C5/C7 v2 rfkillJohn Crispin2016-05-121-1/+1
| | | | | | Fix ARCHER_C7_GPIO_BTN_RFKILL, which is attached to GPIO23 Signed-off-by: Lars Buerding <lb.wrt@metatux.net>
* ar71xx: Add support for Ubiquiti UniFi AP AC PROP.Wassi2016-05-123-1/+72
| | | | | Add support for the Ubiquiti UniFi AP AC PRO Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: Rename unifiac to unifiac-liteP.Wassi2016-05-123-9/+9
| | | | | | | To avoid confusion with different unifiac devices, rename existing target "unifiac" to "unifiac-lite", before "unifiac-pro" is introduced. Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: add TP-Link TL-WR810N supportblogic2016-05-104-0/+147
| | | | | | | | | This patch adds support for the TP-Link TL-WR810N. https://wiki.openwrt.org/toh/tp-link/tl-wr810n Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com> SVN-Revision: 49286
* ar71xx: Fix eth0 support for Ubiquiti UniFi AP ACblogic2016-05-101-0/+1
| | | | | | | Fix eth0 support for the Ubiquiti UniFi AP AC Signed-off-by: Paul Wassi <p.wassi at gmx.at> SVN-Revision: 49277
* ar71xx: Add support for the OMYlink OMY-G1rebootJohn Crispin2016-04-264-0/+135
| | | | | | | | | | https://wiki.openwrt.org/toh/omylink/omy-g1 http://www.omylink.com/ Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49258
* ar71xx: fix build errorHauke Mehrtens2016-04-172-0/+2
| | | | | | | | | | This fixes a build error introduced in r49193. This closes #22230 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 49194
* ar71xx: fix build with kernel 4.4Hauke Mehrtens2016-04-172-0/+8
| | | | | | | | | | The file linux/mdio-gpio.h was moved to linux/platform_data/mdio-gpio.h in kernel 4.4 Reported-by: Arjen de Korte <arjen+openwrt@de-korte.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 49193
* ar71xx: add TP-Link TL-WA901ND-v4 supportJohn Crispin2016-04-094-0/+123
| | | | | | Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com> SVN-Revision: 49158
generated by cgit v1.1 at 2024-07-08 12:19:29 +0000