summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx/files
Commit message (Collapse)AuthorAgeFilesLines
* Revert "ar71xx: prevent spurious ethernet resets from dma hang check false ↵Felix Fietkau2016-06-262-6/+5
| | | | | | positives" This reverts commit 3d58d7f053eae83b59baf5c8b8a58da78653f605.
* ar71xx: prevent spurious ethernet resets from dma hang check false positivesFelix Fietkau2016-06-262-5/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: enable flow control for ethernet MACs with built-in switchFelix Fietkau2016-06-263-1/+11
| | | | | | | | Should fix LAN speed issues on some devices. This is an updated version of the previously reverted commit with the same name. It improves the check for MACs connected to a built-in switch Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "ar71xx/cpe510: use second wifi calibration table"Alexander Couzens2016-06-161-1/+1
| | | | | | | | Using the high power table can damage the device in some cases. This reverts commit bf27ac019c137e7baf90ca6ef0e40945ae871797. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* Revert "ar71xx: enable flow control for ethernet MACs with built-in switch"Felix Fietkau2016-06-141-9/+1
| | | | | | | | This reverts commit 1beb5bec6453abb220c5be4ddb9e6dc02d08d735. It was found to cause the WAN port to fail on some AR934x devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: mach-ubnt-xm.c convert patches to mach fileArne Zachlod2016-06-131-0/+700
| | | | Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ar71xx: enable flow control for ethernet MACs with built-in switchFelix Fietkau2016-06-131-1/+9
| | | | | | Should fix LAN speed issues on some devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for OpenEmbed SOM9331Allan Nick Pedrana2016-06-074-0/+137
| | | | | | | | This patch adds the target profile SOM9331 and configures hardware functionality for the 3x Eth Ports & corresponding LED's, the USB Host, the USART to USB bridge and the System LED. Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
* treewide: replace nbd@openwrt.org with nbd@nbd.nameFelix Fietkau2016-06-076-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add WRTnode2Q supportKeLei Liang2016-06-064-0/+138
| | | | Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
* ar71xx: Fix TL-WR841N v11 LEDs, use separate machineStijn Segers2016-05-312-1/+71
| | | | Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx/cpe510: use second wifi calibration tableAlexander Couzens2016-05-231-1/+1
| | | | | | | The cpe510 has two calibration tables. The first calibration table requires to modify ath9k driver to work (patched tx gain table). Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510Alexander Couzens2016-05-232-6/+25
| | | | | | | Split profile into 2GHz and 5GHz. The 5GHz devices are quite "special". The 2 GHz works perfect. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: add kernel support for the OpenMesh MR1750v2Sven Eckelmann2016-05-232-0/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add kernel support for the OpenMesh OM2P-HSv3Sven Eckelmann2016-05-232-0/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx/cpe510: enable LNA for CPE210/220/510/520Alexander Couzens2016-05-201-0/+6
| | | | | | | The LNA improves the rx path. Within a simple test setup it improved the signal from -60dbm to -40dbm. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: fix DDR write buffer flushing issues with 4.4Felix Fietkau2016-05-151-73/+16
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-LINK TL-WR842N/ND v3Cezary Jackiewicz2016-05-143-8/+105
| | | | | | | | | | | - CPU QCA9531-BL3A - RAM: 64MB - flash: 16MB - USB AP143 platform, similar to tl-wr841n v10/v11, but with USB Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ar71xx: add proper support for Archer-C7 V2John Crispin2016-05-142-4/+41
| | | | | | This has minor differences to the V1 Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Fix TP-LINK Archer-C5/C7 v2 rfkillJohn Crispin2016-05-121-1/+1
| | | | | | Fix ARCHER_C7_GPIO_BTN_RFKILL, which is attached to GPIO23 Signed-off-by: Lars Buerding <lb.wrt@metatux.net>
* ar71xx: Add support for Ubiquiti UniFi AP AC PROP.Wassi2016-05-123-1/+72
| | | | | Add support for the Ubiquiti UniFi AP AC PRO Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: Rename unifiac to unifiac-liteP.Wassi2016-05-123-9/+9
| | | | | | | To avoid confusion with different unifiac devices, rename existing target "unifiac" to "unifiac-lite", before "unifiac-pro" is introduced. Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: add TP-Link TL-WR810N supportblogic2016-05-104-0/+147
| | | | | | | | | This patch adds support for the TP-Link TL-WR810N. https://wiki.openwrt.org/toh/tp-link/tl-wr810n Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com> SVN-Revision: 49286
* ar71xx: Fix eth0 support for Ubiquiti UniFi AP ACblogic2016-05-101-0/+1
| | | | | | | Fix eth0 support for the Ubiquiti UniFi AP AC Signed-off-by: Paul Wassi <p.wassi at gmx.at> SVN-Revision: 49277
* ar71xx: Add support for the OMYlink OMY-G1rebootJohn Crispin2016-04-264-0/+135
| | | | | | | | | | https://wiki.openwrt.org/toh/omylink/omy-g1 http://www.omylink.com/ Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49258
* ar71xx: fix build errorHauke Mehrtens2016-04-172-0/+2
| | | | | | | | | | This fixes a build error introduced in r49193. This closes #22230 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 49194
* ar71xx: fix build with kernel 4.4Hauke Mehrtens2016-04-172-0/+8
| | | | | | | | | | The file linux/mdio-gpio.h was moved to linux/platform_data/mdio-gpio.h in kernel 4.4 Reported-by: Arjen de Korte <arjen+openwrt@de-korte.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 49193
* ar71xx: add TP-Link TL-WA901ND-v4 supportJohn Crispin2016-04-094-0/+123
| | | | | | Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com> SVN-Revision: 49158
* ar71xx: add support for Compex WPJ342John Crispin2016-04-094-0/+190
| | | | | | | | | | | | OpenWrt can be flashed with following uboot commands: tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 49157
* ar71xx: add kernel support for the OpenMesh OM5P-ACv2 boardJohn Crispin2016-04-094-0/+228
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49149
* ar71xx: add kernel support for the OpenMesh OM5P-AC boardJohn Crispin2016-04-094-0/+204
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49141
* ar71xx: WPN824N: enable buttonsJohn Crispin2016-04-011-5/+33
| | | | | | | | Enable buttons connected to the GPIOs of the AR9285. Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> SVN-Revision: 49109
* ar71xx: WPN824N: set WLAN LED nameJohn Crispin2016-04-011-5/+2
| | | | | | | | | Make use of ap9x_pci_setup_wmac_led_name() to set the name of the WLAN LED. Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> SVN-Revision: 49108
* ar71xx: WNR2200: enable control of all LEDs and buttonsJohn Crispin2016-04-011-36/+109
| | | | | | | | | This patch provides full GPIO support for WNR2200 (LEDs and buttons). It exposes all LEDs to operating system, including Ethernet ones. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 49101
* ar71xx: WNR2200: fix for random WLAN MACJohn Crispin2016-04-011-2/+37
| | | | | | | | | | Fix for invalid/random/duplicate WLAN MAC address in WNR2200. Permanent platform MAC is calculated and assigned during system startup. WLAN MAC follows wired Ethernet interface addresses. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 49100
* ar71xx: cosmetic fix of alfa ap120c/ap96 orderingLuka Perkov2016-03-244-14/+14
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 49086
* ar71xx: add support for ap120cLuka Perkov2016-03-234-0/+157
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 49082
* ar71xx: WNR1000v2: enable control of all LEDs and buttonsJohn Crispin2016-03-231-5/+127
| | | | | | | | | This patch provides full GPIO support for WNR1000v2 (LEDs and buttons). It exposes all LEDs to operating system, including Ethernet ones. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 49076
* Revert "ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg"John Crispin2016-03-231-13/+3
| | | | | | | | | | | | | Not all mach-* files set all boards correctly in ETH_CFG. They depend on some preset values by u-boot which were not previously modified by ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps it backward compatible for these boards. This reverts commit 119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49072
* Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x"John Crispin2016-03-2315-27/+17
| | | | | | | | | | | | The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some boards. These boards depend on the preset values of u-boot which may differ. This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49071
* ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR1750John Crispin2016-03-231-1/+23
| | | | | | | | | | | | The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work correctly under OpenWrt. But the global function ath79_setup_qca955x_eth_cfg will not unset all of them to increase the backward compatiblity with older mach-* files. A private (simplified) version for MR1750 can be used instead. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49070
* ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR900John Crispin2016-03-231-1/+23
| | | | | | | | | | | | The MR900 must unset some bits in ETH_CFG which were set by u-boot to work correctly under OpenWrt. But the global function ath79_setup_qca955x_eth_cfg will not unset all of them to increase the backward compatiblity with older mach-* files. A private (simplified) version for MR900 can be used instead. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49069
* ar71xx: WNR1000v2: fix for random WLAN MACJohn Crispin2016-03-201-2/+7
| | | | | | | | | | | Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform MAC is calculated and assigned during system startup. WLAN MAC follows wired Ethernet interface addresses. This is the same fix as for WNR2000v3 and WNR612v2. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 49051
* ar71xx: Use PHY fixups for Open Mesh MR1750John Crispin2016-03-161-3/+22
| | | | | | | | | | | | | | | | | | The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in different ways. u-boot only modifies the ETH_CFG of the QCA955x based on the link speed. But OpenWrt can only modify the PHY delays based on the link speed. This can lead to communication problems when u-boot initializes the ETH_CFG for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY delays to an incompatible value. Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and only rely on the AT803x PHY settings. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49031
* ar71xx: Use PHY fixups for Open Mesh MR900John Crispin2016-03-161-3/+22
| | | | | | | | | | | | | | | | | | The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in different ways. u-boot only modifies the ETH_CFG of the QCA955x based on the link speed. But OpenWrt can only modify the PHY delays based on the link speed. This can lead to communication problems when u-boot initializes the ETH_CFG for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY delays to an incompatible value. Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and only rely on the AT803x PHY settings. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49030
* ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955xJohn Crispin2016-03-1617-19/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some u-boot versions for QCA955x change the delays based on the link speed during boot. This usually breaks the support of other linkspeeds when OpenWrt is booted. It also conflicts with the at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own values in QCA955X_GMAC_REG_ETH_CFG. The default RGMII values from the Atheros u-boot are currently used to preset the existing mach files. These may have to be adjusted for boards using different values but which are not currently set them explicitely in OpenWrt. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Christian Beier <cb@shoutrlabs.com> Cc: Chris R Blake <chrisrblake93@gmail.com> Cc: Benjamin Berg <benjamin@sipsolutions.net> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Cc: Matthias Schiffer <mschiffer@universe-factory.net> Cc: Dirk Neukirchen <dirkneukirchen@web.de> Cc: Christian Mehlis <christian@m3hlis.de> Cc: Luka Perkov <luka@openwrt.org> Cc: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 49029
* ar71xx: Clear bits in ath79_setup_qca955x_eth_cfgJohn Crispin2016-03-161-3/+13
| | | | | | | | | | | Some u-boot versions for QCA955x set currently not cleared bits depending on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c file is responsible to select the correct configuration bits and thus the ath79_setup_qca955x_eth_cfg has to clear the unset. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49028
* ar71xx: Add support for the OMYlink OMY-X1John Crispin2016-03-164-0/+117
| | | | | | | | | | | | This patch adds support for the OMYlink OMY-X1 https://wiki.openwrt.org/toh/omylink/omy-x1 http://www.omylink.com/ Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49026
* ar71xx: Arduino Yun board 'WLAN RST' button supportJohn Crispin2016-03-101-0/+21
| | | | | | | | This patch adds support for Arduino Yun board "WLAN RST" button. Signed-off-by: Hirokazu MORIKAWA <morikw2@gmail.com> SVN-Revision: 48983
* ar71xx: add support for the Telldus TellStick ZNet LiteJohn Crispin2016-03-104-0/+141
| | | | | | Signed-off-by: Micke Prag <micke.prag@telldus.se> SVN-Revision: 48977
generated by cgit v1.1 at 2024-10-31 09:32:46 +0000