summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx/files
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: ZyXEL NBG6716 led/buttons cleanupJohn Crispin2015-02-121-12/+12
| | | | | | | | | | ZyXEL NBG6716 led/buttons cleanup - improper numbered leds - improper named buttons Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com> SVN-Revision: 44417
* ar71xx: dir-505: fix reset button gpio active_low valueJohn Crispin2015-02-091-1/+1
| | | | | | | | Fix 'active_low' default value for the reset button on DIR-505. Signed-off-by: Rocco Folino <rocco@devzen.net> SVN-Revision: 44360
* ar71xx: Add support for MERCURY MAC1200RJohn Crispin2015-02-091-0/+155
| | | | | | | | | This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> SVN-Revision: 44359
* ar71xx: fix nbg6716 power and usb ledJohn Crispin2015-02-091-2/+2
| | | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Marcin Mikolajczak <gr4ffy@gmail.com> SVN-Revision: 44358
* ar71xx: rb2011: apply patch to fileLuka Perkov2015-02-071-0/+7
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44314
* ar71xx: qihoo: define flash variable as staticLuka Perkov2015-02-071-1/+1
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44306
* ar71xx: add support for the TP-LINK TL-WR941ND v5John Crispin2015-02-041-0/+61
| | | | | | | | | This device is very similar to the TL-WR841N v8, only two LED GPIOs are different. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 44255
* ar71xx: Revert "added board support for compex wpj558"John Crispin2015-02-021-187/+0
| | | | | | | | This reverts commit f7873071561d82e75ba2dc46433a2982fef8ac6f. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44245
* added board support for compex wpj558John Crispin2015-02-021-0/+187
| | | | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 44237
* ar71xx: add Netgear WNR1000v2/WNR1000v2-VC support (#18633)John Crispin2015-01-301-1/+26
| | | | | | | | | | | The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are pretty much the same as WNR2000v3/WNR612v2, therefore the same initialization code and flash layout is used. Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com> Tested-by: Douglas Fraser <1dsfraser@gmail.com> SVN-Revision: 44221
* ar71xx: fix D-Link DIR-615 rev. C1 WLAN MAC addressJohn Crispin2015-01-281-3/+5
| | | | | | | | | Fix the WLAN MAC address to match the one printed on the label by using the correct address from the ART instead of the address of the LAN interface. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 44183
* ar71xx: add support for TL-WA701ND v2John Crispin2015-01-201-0/+116
| | | | | | Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com> SVN-Revision: 44063
* Belkin AC 1750 DB (F9K1115v2) supportImre Kaloz2014-12-171-0/+189
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 43734
* ar71xx: improve ethernet driver cache footprint by removing an unnecessary ↵Felix Fietkau2014-12-093-27/+36
| | | | | | | | pointer Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43588
* ar71xx: dev-eth: replace mdelay callsJohn Crispin2014-12-071-2/+2
| | | | | | | | Similar to patch 2. Replace further mdelay calls. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 43540
* ag71xx: replace delay with sleep callsJohn Crispin2014-12-072-6/+6
| | | | | | | | | | | | I don't see that we're in an atomic context so there's no need to busy-wait. Therefore replace the delay with sleep calls. See also Documentation/timers/timers-howto.txt. It states: "In general, use of mdelay is discouraged and code should be refactored to allow for the use of msleep." Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 43539
* ag71xx: replace fixed PHY reset wait time in ar7240sw_setupJohn Crispin2014-12-071-1/+28
| | | | | | | | | Replace the fixed wait time of 1s with polling for BMCR_RESET to be cleared on all PHYs. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 43538
* add D-link DGL-5500 A1 supportImre Kaloz2014-11-271-0/+150
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 43401
* ar71xx: add support for TP-LINK CPE210/220/510/520John Crispin2014-11-261-0/+107
| | | | | | | | | | This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These devices are very similar to the Ubiquiti NanoStations, but with better specs: faster CPU, more RAM, 2x2 MIMO. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 43385
* Netgear R6100 supportImre Kaloz2014-11-261-0/+146
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 43382
* ar71xx: Added support for D-link DHP-1565 rev. A1John Crispin2014-11-191-0/+170
| | | | | | Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl> SVN-Revision: 43307
* ar71xx: Fix the sys LEDs on the EasyLink M150 and miniJohn Crispin2014-11-142-2/+2
| | | | | | | | Sets the system LED on the EasyLink M150 and mini to lower-case "easylink" Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 43271
* ar71xx: add kernel support for the OpenMesh MR900v2John Crispin2014-11-141-0/+1
| | | | | | Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 43265
* ar71xx: add kernel support for the OpenMesh MR900 boardJohn Crispin2014-11-141-0/+158
| | | | | | Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 43258
* ar71xx: add support for Netgear WNR2000v4John Crispin2014-11-031-0/+175
| | | | | | Signed-off-by: Michaël Burtin <mburtin@gmail.com> SVN-Revision: 43173
* ar71xx: add support for buffalo WZR-450HP2Felix Fietkau2014-10-221-0/+221
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43026
* wr1043nd-v2: Change .code of the wi-fi button to KEY_RFKILLJohn Crispin2014-10-141-4/+4
| | | | | | | | | | | | This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2 from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason for this change is, that the KEY_WIFI button code is not recognized by the hotplug subsystem. This means that the userspace is not notified about the button being pressed which effectively renders it useless. Signed-off-by: Josef Gajdusek <atx@atx.name> SVN-Revision: 42922
* ar71xx: Fix LED definitions for the DRAGINO2 boardJohn Crispin2014-10-141-17/+26
| | | | | | | | | | | | | | This patch fixes LED definitions for the DRAGINO2 board. 1. It renames the Router/USB led to System, as it is now marked "SYS" on the board. 2. It gives control of the LAN and WAN leds and some other GPIOs to Linux. 3. It fixes the active_low property for the LAN and WAN leds. 4. It sets up WLAN, LAN and WAN leds in the UCI defaults. 5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status. Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> SVN-Revision: 42897
* ar71xx: fix reset button gpio for OM2P/OM2P-HSJohn Crispin2014-10-061-1/+1
| | | | | | | | | | | A typo in the definition for the OM2P reset button disabled its functionality in OpenWrt. The actual button for these two devices is "1" and not "11". Signed-off-by: Oren Poleg <oren@poleg.org> [sven@open-mesh.org: added a commit subject+message] Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 42782
* ar71xx: add qihoo 360 c301 router supportJohn Crispin2014-09-151-0/+166
| | | | | | | | | | | | | | | Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac. Its chipset is AR9344 + AR9882 with two 16MB flashes. This patch adds its initial support. v2: * use mtd_get_mac_ascii to fetch MAC address for ath10k. * use ath79_register_pci to initialize AR9882. Signed-off-by: Weijie Gao <hackpascal@gmail.com> SVN-Revision: 42552
* ar71xx: ack completed tx descriptors only after the full frame has been ↵Felix Fietkau2014-09-101-10/+16
| | | | | | | | completed Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42457
* ath79: dev-eth: Don't advertise 1gbit in link code word on ar9331Felix Fietkau2014-09-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | While the AR9331 has a gigabit MAC towards the internal switch, the integrated PHYs however are only 100-base-tx capable. The existing code however advertieses gigabit capability in the link status word. If you attach such a PHY to a gigabit capable switch on the remote end, with some probability it attempts to negotiate gigabit and fails, falling baco to the AR9331 assuming a 10mbit half-duplex link. This has been observed quite frequently with the Carambola2 and gigabit capable switches. In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally for both AR9331 ethernet ports. This is most likely wrong. Despite the two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a 100base-T PHY via MII. The has_gbit attribute is used in the ethernet driver to determine the supported link modes. So either pdata->has_gbit is not set to 1 anymore, or the ethernet driver needs to be modified to determine the advertised link code word on another criteria than pdata->has_gbit. This patch implements the former solution. Signed-off-by: Harald Welte <laforge@gnumonks.org> SVN-Revision: 42432
* ar71xx: re-enable descriptor splitting on ar716x after the previous bugfixes ↵Felix Fietkau2014-09-061-2/+0
| | | | | | | | (#13072) Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42429
* ar71xx: fix off-by-one error in packet descriptor splitting (patch from #13072)Felix Fietkau2014-09-061-1/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42428
* ar71xx: on ar716x, split ethernet packets in 512 byte chunks instead of 256 ↵Felix Fietkau2014-09-061-1/+1
| | | | | | | | (improves performance) (patch from #13072) Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42427
* ar71xx: disable ethernet descriptor splitting for now, as it seems to cause ↵Felix Fietkau2014-08-301-0/+2
| | | | | | | | tx hangs in some setups Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42333
* ar71xx: split packets into multiple descriptors on ar716xFelix Fietkau2014-08-293-28/+105
| | | | | | | | | | | This improves performance when doing concurrent rx/tx on a single ethernet MAC, e.g. when routing between VLANs. Fixes #13072 Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42328
* ar71xx: use ETH_ALEN for consistencyJohn Crispin2014-08-251-3/+3
| | | | | | Signed-off-by: Forest Crossman <cyrozap@gmail.com> SVN-Revision: 42280
* ar71xx: TL-WR1043N/ND v2: Fix MAC address of WMACJohn Crispin2014-08-181-3/+1
| | | | | | | | | | | | This sets the MAC address of the WLAN interface to the "official" primary MAC address (the one on the label under the devices, and the one used with the stock firmware). The MAC address used so far (primary-1) isn't even used at all with the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the WAN interface (like OpenWrt does with this patch). Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 42193
* ar71xx: Fix 2.4G WiFi LED of the OpenMesh MR600 boardJohn Crispin2014-08-181-0/+1
| | | | | | | | | | The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the mini-PCIe device. Not configuring the LED pin inside the platform data makes it impossible to configure it through any standard OpenWrt tool. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 42184
* add support for the NC-LINK SMART-300Imre Kaloz2014-08-111-0/+135
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 42130
* ar71xx: add linux 3.14 supportFelix Fietkau2014-08-071-6/+3
| | | | | | | Signed-off-by: Zhao, Gang <gang.zhao.42@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42038
* ar71xx: update Carambola2 platform dataFelix Fietkau2014-08-041-9/+0
| | | | | | | | | | | | Change list: * Remove button info on GPIO12, there is no button there. * Remove nvram mtd partition, as it's not used for anything, saves 64k for user data. Tested building for carambola2 target. Signed-off-by: Mantas Pucka <mantas@8devices.com> SVN-Revision: 41993
* ar71xx: oolite: the buttons are not active_lowJohn Crispin2014-08-011-3/+3
| | | | | | | | | this caused factory resets when reboot was pressed Signed-off-by: Brent Thomson <brentthomson@gmail.com> Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41932
* add support for the archer c5Imre Kaloz2014-07-231-1/+10
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41814
* ar71xx: Fix GL.iNet WLAN LEDJohn Crispin2014-07-211-1/+1
| | | | | | | | LED script expects WLAN LED to be "gl-connect:red:wlan". Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 41793
* ar71xx: split wndr4300 and wndr3700v4 into 2 seperate mips machinesJohn Crispin2014-07-211-1/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41788
* ar71xx: add kernel support for the OpenMesh OM5P boardJohn Crispin2014-07-201-0/+122
| | | | | | | | Signed-off-by: Marek Lindner <marek@open-mesh.com> [sven@open-mesh.com: Rebased] Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 41769
* ar71xx: add kernel support for the EnGenius EAP300 v2 boardGabor Juhos2014-07-141-0/+101
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 41658
* ar71xx: add kernel support for the Tube2H boardGabor Juhos2014-07-141-0/+113
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 41649
generated by cgit v1.1 at 2024-11-15 04:49:17 +0000