summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx/image/generic.mk
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: add support for Fritz!WLAN Repeater 450EDavid Bauer2018-06-211-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!WLAN Repeater 450E SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4GHz WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - Most LEDs Not working: - 2 RSSI LEDs AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they control over MDIO. Our driver doesn't expose these LEDs as GPIOs. While it is possible to implement this feature, it would require an additional kernel patch for a minor functionality. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the Device afterwards to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit b4bf43c66767648f98494dd5f44e1301024b577c)
* ar71xx: fix AVM package selectionDavid Bauer2018-06-091-2/+2
| | | | | | | The AVM package selection partially broke with the addition of the FRITZ!Box 4020. This commit restores the intended behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: Add support for PISEN TS-D084Chuanhong Guo2018-05-241-0/+11
| | | | | | | | | | | | | | | | | | | PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz (AR9331) - 1x USB 2.0 Flash instruction: The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit a789c0f49159c618d990541c23e00630f7296ebc)
* ar71xx: Fix build for dap-1330-a1 boardHauke Mehrtens2018-05-241-1/+1
| | | | | | | | | | | | | | | | | Using a version number of 16 character causes a buffer overflow in the version number overwriting the first bit of the signature in the mkdapimg2 tool. I am not sure if the version number should be null terminated or not. This patch reduces the size of the version number by removing the number of private commits from it. This was the original version number which caused problems: OpenWrt-r6727+10 Now it uses this version number: OpenWrt-r6727 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit ae8ff1c65c4ea4e0b2e1e8ef94fad87587d979bc)
* ar71xx: add support for Fritz!Box 4020David Bauer2018-05-071-6/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs Not working: - USB port Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: change brand name WHQX to QxwlanPeng Zhang2018-04-061-6/+6
| | | | Signed-off-by: Peng Zhang <sd20@qxwlan.com>
* ar71xx: Add support for D-Link DAP-1330 a1Nicolò Veronese2018-04-051-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of RAM (DDR1) - 8 MB of FLASH - 2T2R 2.4 GHz - 2x external antennas - 6x LED (2 are bi-color), 2x button - 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc) Flash instruction: use "factory" image directly in vendor GUI. This device has a recovery system that assign the ip addr of env variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself. The recovery it's triggered by a not bootable firmware, or pressing the reset button during the bootloader startup (first 30 seconds). The recovery uses a http page to restore the firmware, and it's checking the firmware image header, so use the "factory" image to restore or the original firmware. You can access vendor firmware over serial using: - login: root - password: linuxrocks Image was tested only in EU version of the device, but should work also with the same device version sold in other countries. Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* ar71xx: fix Fritz 300e initramfs imageMathias Kresin2018-03-181-0/+1
| | | | | | Create an initramfs that can be used with the EVA bootloader. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add support for GainStrong Oolite V5.2Piotr Dymacz2018-02-221-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are available on castellated pins. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 5x 10/100 Mbps Ethernet (all ports available on castellated pins) - 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA - 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11) - 3x U.FL - 1x USB 2.0 The dedicated development board includes 5 FE ports, USB 2.0 port, two buttons (one directly connected to SOC reset input), header with all GPIOs and several LEDs. Flash instruction: Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to flash OpenWrt firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: rework GainStrong devices supportPiotr Dymacz2018-02-221-13/+12
| | | | | | | | | - combine support for Oolite/MiniBox V1.0 in single mach-*.c file - fix model/board names - include correct/full vendor name - drop redundant package and factory image Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for AR9331 based Hak5 devicesSebastian Kinne2018-02-221-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for AR9331 based Hak5 penetration testing tools: - WiFi Pineapple NANO - LAN Turtle - Packet Squirrel WiFi Pineapple NANO specifications: - SoC: Atheros AR9331 (400 MHz) - RAM: 64 MB (DDR2) - FLASH: 16 MB - WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus) - Ethernet: 1x FE over USB (ASIX AX88772A) - Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD - Power: USB 5 V, 1.5 A - Other: status LED, reset button LAN Turtle specifications: - SoC: Atheros AR9331 (400 MHz) - RAM: 64 MB (DDR2) - FLASH: 16 MB - WiFi: none - Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B) - Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot - Power: USB 5 V, 0.5 A - Other: status LED, reset button (inside, on PCB) Packet Squirrel specifications: - SoC: Atheros AR9331 (400 MHz) - RAM: 64 MB (DDR2) - FLASH: 16 MB - WiFi: none - Ethernet: 2x FE (AR9331) - Ports: 2x RJ45, 1x USB 2.0 - Power: USB 5 V, 0.12 A - Other: status LED, reset button, 4-way switch Flash instructions for all 3 devices: Original firmware is based on OpenWrt. Use sysupgrade via SSH to flash. Signed-off-by: Sebastian Kinne <contact@sebkinne.com> [squashed commits, combined and reworked mach files, aligned board naming with general convention, fixed minor issues, tested on real hardware, reworded commit subject and description] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: YunCore AP90Q image supports also AP80QPiotr Dymacz2018-02-221-1/+1
| | | | | | | Vendor released new model (AP80Q) which is identical from hardware point of view with already supported AP90Q. Include AP80Q in machine name. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore T830Piotr Dymacz2018-02-221-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore T830 is a simple N300 router with 5-port FE switch, detachable antennas and USB 2.0 port. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 5x 10/100 Mbps Ethernet - 2T2R 2.4 GHz (QCA9531), with ext. PA (SKY65174-21) and LNA - two external, detachable antennas (RP-SMA) - 1x USB 2.0 - 8x LED (7 driven by GPIO) - 1x button (reset) - DC jack for main power input (12 V) - UART and JTAG headers on PCB Flash instruction: 1. First, gain root access to the device, following below steps: - Login into web gui (default password/IP: admin/192.168.188.253). - Go to "Advanced" -> "Management" -> "System" and download backup of configuration (bakfile.bin). - Open the file as tar.gz archive, edit/update "shadow" file and change hash of root password to something known. - Repack the archive, rename it back to "bakfile.bin" and use to restore configuration of the device. - After that, device will reboot and can be accessed over SSH. 2. Then, install OpenWrt: - Login over SSH and issue command: fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" - Upload "sysupgrade" image and install it (only if previous command succeeded) with command: "sysupgrade -n -F openwrt-...". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Samsung WAM250Piotr Dymacz2018-02-221-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless hub, dedicated for Samsung Shape Wireless Audio System. The device is based on Atheros AR9344. FCC ID: A3LWAM250. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet - 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA - 1x USB 2.0 - 4x LED (all are driven by GPIO) - 2x button (reset, wps/speaker add) - DC jack for main power input (14 V) - UART header on PCB (J4, RX: 3, TX: 5) Flash instruction: This device uses dual-image (switched between upgrades) with a common jffs2 config partition. Fortunately, there is a way to disable this mode so that more flash space can be used by OpenWrt image. You can easily access this device over telnet, using root/root credentials (the same also work for serial console access). 1. Make sure that your device uses second (bootpart=2) image using command: "fw_printenv bootpart". 2. If your device uses first image (bootpart=1), perform upgrade to the latest vendor firmware (after the update, device should boot from second partition) using web gui (default login: admin/1234567890). 3. Rename "sysupgrade" image to "firmware.bin", download it (you can use wget, tftp or ftpget) to "/tmp" and issue below commands: mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}') mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin) fw_setenv bootpart fw_setenv bootcmd "bootm 0x9f070000" reboot Revert to vendor firmware instruction: 1. Download vendor firmware to "/tmp" device and issue below commands: fw_setenv bootpart 1 sysupgrade -n -F SS_BHUB_v2.2.05.bin Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix COMFAST CF-E375AC supportPiotr Dymacz2018-02-221-1/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E385ACPiotr Dymacz2018-02-221-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E385AC is an AC2200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558 + QCA9984 + QCA8337N. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 256 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100/1000 Mbps Ethernet, with PoE support - 3T3R 2.4 GHz (QCA9558), with external LNA and PA (SE2576L) - 4T4R 5 GHz (QCA9984), with external FEM (SKY85728-11) - 7x internal antennas - 1x RGB LED (driven by GPIO) - 1x button (reset) - UART, LEDs/GPIO and USB headers on PCB - external watchdog (Pericon Technology PT7A7514) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: remove unnecessary packages from COMFAST devicesPiotr Dymacz2018-02-221-5/+9
| | | | | | | swconfig and uboot-envtools packages are not required by any of the supported COMFAST devices. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: rename COMFAST CF-E355AC to CF-E355AC v1Piotr Dymacz2018-02-221-5/+5
| | | | | | | | There are now supported two versions of the CF-E355AC board which differ in 802.11ac radio chip. Include version number in board, model, image filename, etc., also for the v1. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: simplify Embedded Wireless definitionsPiotr Dymacz2018-02-221-7/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: generic: use simply expanded variablesPiotr Dymacz2018-02-221-16/+16
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: generic: clean up trailing whitespacePiotr Dymacz2018-02-221-1/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E355AC v2Ding Tengfei2018-02-221-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9886. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 128MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a, WAVE 2 - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [updated kernel config for both boards] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2Peng Zhang2018-02-221-0/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334. Specification: - 750/400/250 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11) - 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 1x USB 2.0 - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 2-pos switch - 1x DC jack for main power input (9-48 V) - UART (J5) and LEDs (J13) headers on PCB WHQX E600G is based on Qualcomm QCA9531. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11) - 2x 10/100 Mbps Ethernet - 6x LED (1x RGB, 5 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-12 V) - UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB Important notice: First version of these boards are using different mtd layout, with ART data at the end. You should not use v2 images on v1 board because it will result in lost of ART data! Flash instruction (using U-Boot CLI and tftp server): 1. Configure PC with static IP 192.168.1.10 and tftp server. 2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. 3. Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. 4. Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): 1. Configure PC with static IP 192.168.1.xxx(2-254)/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. 3. Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: Peng Zhang <sd20@qxwlan.com> [reworked: image generation code, mach-* files, commit description, fixed minor code style issues, rebased on master] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Add eTactica EG-200 supportKarl Palsson2018-02-131-0/+13
| | | | | | | | | | | | | | EG-200 is a DIN rail mountable device with one ethernet port, wifi, an RS-485 port, and an internal USB attached uSD card reader. Two leds, "modbus" and "etactica" are managed by userspace applications in factory firmware. Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ar71xx:add support for COMFAST CF-E375ACDing Tengfei2018-02-111-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337. Short specification: 2x 10/100/1000 Mbps Ethernet, with PoE support 128MB of RAM (DDR2) 16 MB of FLASH 3T3R 2.4 GHz, 802.11b/g/n 2T2R 5 GHz, 802.11ac/n/a, wave 2 built-in 5x 3 dBi antennas output power (max): 500 mW (27 dBm) 1x RGB LED, 1x button built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn>
* build: replace uses of OpenWrt with $(VERSION_DIST)Felix Fietkau2018-02-051-3/+3
| | | | | | This makes the distribution name more configurable. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add ew-balin platform from Embedded WirelessCatrinel Catrinescu2018-01-251-0/+9
| | | | | | | | | | | | | | | | | | | Add the Embedded Wireless "Balin" platform SoC: QCA AR9344 or AR9350 RAM: DDR2-RAM 64MBytes Flash: SPI-NOR 16MBytes WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n Ethernet: 3 x 10/100 Mb/s USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up PCI-Express: 1 x lane PCIe 1.2 UART: 1 x Normal, 1 x High-Speed JTAG: 1 x EJTAG GPIO: 10 x Input/Output multiplexed The module comes already with the current vanilla OpenWrt firmware. To update, use "sysupgrade" image directly in vendor firmware. Signed-off-by: Catrinel Catrinescu <cc@80211.de>
* ar71xx: add support for GL.iNet GL-AR750Piotr Dymacz2018-01-151-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3x 10/100 Mbps Ethernet - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 1x USB 2.0 (power controlled by GPIO) - 1x microSD (GL857L) - 3x LED (all driven by GPIO) - 1x button (reset) - 1x 2-pos switch - header for optional PoE module - 1x micro USB for main power input - UART + I2C header on PCB Flash instruction: Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used to flash OpenWrt/LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: move Sitecom WLR-8100 from legacy to genericPiotr Dymacz2018-01-151-0/+10
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network R36APiotr Dymacz2018-01-151-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36A is a successor of the previous model, the R36 (Ralink RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB - 1x USB 2.0 (power controlled by GPIO) - 6x LED (5 of them are driven by GPIO) - 2x button (reset, wifi/wps) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Teltonika RUT900Piotr Dymacz2018-01-151-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is an industrial 3G router based on Atheros AR9344. There are available 3 other models in RUT9xx series: RUT905, RUT950 and RUT955, which differ in availability of additional I/O ports, built-in GSM modem type, GPS antenna and other features. FCC ID of the RUT950 model (LTE module built-in): 2AET4-RUT950. This patch adds support for the RUT900 model only but can be easily extended to cover whole series. Also, as there are several different 3/4G modules (Huawei, Quectel, Telit) used in whole series, packages required for WWAN support are not included by default. It is up to the user to install required software for built-in modem. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA - built-in 3G module (example: Telit HE910-D) - 2x miniSIM slot - 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G) - PCA9539 16-bit GPIO I2C expander - 12x LED (4 are driven by AR9344, 7 by PCA9539) - 1x button (reset) - DC jack for main power input (9-30 V) - UART available on PCB edge connector Serial console pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network N5QPiotr Dymacz2018-01-141-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network N5Q is a successor of previous model, the N5 (outdoor CPE/AP, based on Atheros AR7240 + AR9280). New version is based on Atheros AR9344. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm - 8x LED (7 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmare which is based on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP91-5GPiotr Dymacz2018-01-141-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros AR7240 + AR9280. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 32 MB of RAM (DDR1) - 8 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm - 6x LED (5 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART and LEDs headers on PCB Flash instruction: Use "factory" image in vendor GUI (in case of problems, make sure your board has up to date firmware). Alternatively, TFTP in U-Boot can be used: select option "2. Load system code then write to Flash via TFTP" during early boot and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: create new ar71xx/tiny subtarget for 4MB flash devicesMatthias Schiffer2018-01-131-12/+2
| | | | | | | | | | | This new subtarget sets the small_flash flag and removes unused kernel configuration. small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default configuration; removing unneeded hardware support from ar71xx/tiny saves another ~18KB (both after LZMA). Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-7/+26
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* merge: targets: update image generation and targetsZoltan HERPAI2017-12-081-2/+2
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ar71xx: add support for Wallys DR342Piotr Dymacz2017-11-141-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342. Short specification: - 560/450/225 MHz (CPU/DDR/AHB) - 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V) - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm - 2x MMCX connectors - miniPCIe connector with PCIe and USB 2.0 buses - optional miniSIM slot - 7x LED, 1x button - UART, (E)JTAG and LED headers - 1x DC jack for main power (12-56 V) Flash instruction (do it under U-Boot, using UART): 1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: deactivate some boards with too small kernel partitionsHauke Mehrtens2017-10-221-1/+0
| | | | | | | | | | | | | | | | | | | This affects the following boards: * dr344 * archer-c58-v1 * archer-c60-v1 * tl-wr902ac-v1 * tl-wr942n-v1 * ubnt-uap-pro * ubnt-unifi-outdoor-plus The build fails for any of these boards because the resulting kernel image will not fit into the kernel partition. When CONFIG_KERNEL_KALLSYMS is not set it could be that the kernel will fit onto the board again, this is the case for release images. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: ew-dorin target moved from legacy to genericCatrinel Catrinescu2017-10-071-0/+20
| | | | | | Embedded Wireless Dorin platform moved from legacy to generic Signed-off-by: Catrinel Catrinescu <cc@80211.de>
* ar71xx: add metadata to wpj344 and wpj558 imagesEnrique Giraldo2017-09-101-0/+6
| | | | | | | | This adds metadata to wpj344 and wpj558 images to prevent loading firmware of wpj344 into wpj558 and vice versa. This until now was possible and break the units and had to be recovered from the uboot. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
* ar71xx: add support for COMFAST CF-E355ACEnrique Giraldo2017-09-101-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9882. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 64MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net> [whitespace fixes, ac radio caldata offset fix] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-USB150Piotr Dymacz2017-09-101-0/+13
| | | | | | | | | | | | | | | | | | | | | GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4) - 1T1R 2.4 GHz - 2x LED, 1x button - UART header on PCB Flash instruction: Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used to flash LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP121FPiotr Dymacz2017-07-221-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users. Device is based on Atheros AR9331 WiSoC and is running a custom version (updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR1) - 16 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz - 1x microSD (optional, on separate PCB) - 3x LED, 1x button, 1x switch - UART header on PCB Flash instruction (under U-Boot web recovery mode): 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: simplify Meraki MR16 device definitionPiotr Dymacz2017-07-091-10/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: move Arduino Yun to generic building codeCamille Bilodeau2017-06-291-0/+10
| | | | | | | | | | | | | | | | | | Migrate Arduino Yun from legacy to generic building code. Note: the mtd partitioning is changed to adopt the LEDE default partitioning. It allows to have a kernel bigger than 1280k. It is necessary as kernel > 4.4 with default LEDE configuration grows bigger. To use the new partitioning, you need to update your U-Boot env in advance: setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro" setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000" saveenv Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
* ar71xx: add AVM FRITZ!WLAN Repeater 300E supportMathias Kresin2017-06-241-0/+13
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: AR7242 (Virian 400MHz) * RAM: 64 MB DDR (W9751G6JB-25) * Flash: 16MB SPI flash (S25FL129PIF) * WiFi: AR9382 (2.4/5GHz) + 2x SE2595L * LAN: 1x1000M (PEF7071V) To install LEDE via EVA bootloader, a FTP connection need to be established to 192.168.178.1 within the first seconds after power on: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: move WRTnode2Q to generic build targetPiotr Dymacz2017-06-111-0/+9
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: use simply expanded variablesPiotr Dymacz2017-06-111-161/+161
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: update GL.iNet boards DEVICE_TITLEPiotr Dymacz2017-06-111-5/+5
| | | | | | | | Use "GL.iNet" as vendor name (based on information from the vendor, this is registered name of the company) and align model names with official website. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: fix 8devices boards DEVICE_TITLEPiotr Dymacz2017-06-111-2/+2
| | | | | | Be consistent with DEVICE_TITLE syntax and use vendor + board names. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
generated by cgit v1.1 at 2024-06-29 13:55:06 +0000