summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx/image
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: enable nand-utils in the mikrotik subtarget to ensure it makes it to ↵Felix Fietkau2017-05-121-2/+2
| | | | | | | | initramfs Without it, sysupgrade from initramfs to nand fails Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add TP-LINK TL-WR841N/ND v12 imageVittorio Gambaletta2017-04-201-1/+7
| | | | | | | | | | | | | This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC ID, same TFTP image name...). If the stock firmware web interface doesn't accept LEDE factory image, it can be flashed via the U-Boot TFTP recovery mode, by long-pressing the reset button after power on. The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12). Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
* ar71xx: add ath10k driver and firmware for Netgear R6100 to firmware imageStijn Segers2017-03-111-1/+1
| | | | | | | | A Netgear R6100 owner reported the LEDE images lack the ath10k driver and firmware [1]. This patch adds both to the R6100 image. [1] https://forum.lede-project.org/t/netgear-r6100-5ghz-wifi-not-working-after-initial-install/2222 Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx: Remove images for rb-941-2ndThibaut VARENE2017-02-191-2/+0
| | | | | | | | | | The code that generates this image is broken in many ways. The new code currently in master generates images that will not be compatible with the ones in 17.01. To avoid a migration nightmare, this patch removes image generation for this device in 17.01 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: fix DEFAULT_PACKAGES for mikrotik devicesFelix Fietkau2017-02-151-1/+2
| | | | | | Include packages from the default profile for NAND devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: Add missing device package om-watchdog for MR1750Sven Eckelmann2017-02-151-1/+1
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add OpenMesh A40 to OpenMesh A60 profileSven Eckelmann2017-02-151-1/+1
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: create profile and build image for the OpenMesh A60 boardSven Eckelmann2017-02-152-0/+8
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: Remove the v2/v3 from the OpenMesh profile namesSven Eckelmann2017-02-151-4/+4
| | | | | | | The list of v2/v3 devices is getting longer and makes reading the names of the profiles unnecessary hard. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add missing DEVICE_TITLE for mikrotik devicesFelix Fietkau2017-02-011-0/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: improve Mikrotik hAP Lite device supportAlex Samorukov2017-02-011-2/+3
| | | | | | | | - remove CONFIG_MTD_SPI_NOR_USE_4K_SECTORS - enable jffs2 support - fix sysupgrade Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
* ar71xx: add support for RB-941-2nDThibaut VARENE2017-02-011-0/+19
| | | | | | | | | | | | | | | | Add full support for Mikrotik RB-941-2nD (hAP lite) Original patch by Sergey Sergeev <adron@yapic.net> and more information is available here: https://wiki.openwrt.org/toh/mikrotik/rb941_2nd I updated and adapted the patch to apply cleanly to LEDE trunk and added proper numbering for the switch ports (matching case labels). Tested working on actual hardware with the information provided in the above webpage. Sysupgrade works. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: convert mikrotik routerboard support to UBIFelix Fietkau2017-02-012-0/+25
| | | | | | | | | | Remove the wget2nand script, drop the need for manual installation, use sysupgrade instead. There are now two different NAND images, one for 64 MiB flashes, the other for >= 128 MiB Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: prepare jffs2 partition properly in factory.bin for BHR-4GRV2FUKAUMI Naoki2017-01-281-1/+1
| | | | | | "pad-rootfs" is required just after "append-rootfs". Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
* ar71xx: fix legacy image build errorFelix Fietkau2017-01-111-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: drop references to madwifiStijn Tintel2017-01-101-3/+3
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-Link WBS210/510Matthias Schiffer2017-01-051-1/+17
| | | | | | | The devices are mostly identical to the CPE210/510, but use external antennas. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: RE450: enable building of TP-Link RE450Radek Dostál2016-12-221-0/+16
| | | | Signed-off-by: Radek Dostál <rd@radekdostal.com>
* firmware-utils: kernel image generator for TP-Link RE450Tal Keren2016-12-221-0/+10
| | | | | | | | | | | | | | | | | The firmware image that is used in TP-Link RE450 (and some more devices from the RE series) is tplink-safeloader. In the kernel partition, the kernel is compressed in a regular tp-link firmware that is just used for booting. Since it is only used for compressing and booting, only four fields are filled in the header: Vendor, version, kernel load address and kernel entry point. mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such images. It also specifies the hardware id (as it is in the product info section), so when doing a sysupgrade - the existing code will check for hardware compatibility. Signed-off-by: Tal Keren <kooolk@gmail.com> [rd@radekdostal.com: add build target to .../image/tp-link.mk] Signed-off-by: Radek Dostál <rd@radekdostal.com>
* ar71xx: remove redundant -j from TL-WR1043ND v4 kernel build commandMatthias Schiffer2016-12-211-1/+1
| | | | | | | mktplinkfw ignores -j in combined mode, the EOF marker is added by tplink-safeloader. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add support for TP-LINK WR1043ND v4Ludwig Thomeczek2016-12-201-1/+18
| | | | Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: rename mktplinkfw-initramfs to more generic mktplinkfw-combinedMatthias Schiffer2016-12-201-5/+5
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add support for TP-LINK TL-WR940N v4David Lutz2016-12-161-1/+12
| | | | Signed-off-by: David Lutz <kpanic@hirnduenger.de>
* ar71xx: Added missing support for Linksys E2100LGad Krumholz2016-12-141-0/+1
| | | | | | | | | | | | | It's based on the WRT160NL according to https://wiki.openwrt.org/toh/linksys/e2100l Based on research done here: https://forum.openwrt.org/viewtopic.php?id=24244 and here: https://forum.openwrt.org/viewtopic.php?pid=120791#p120791 this patch was conceived. Signed-off-by: Gad Krumholz <gad.krumholz@gmail.com> [Jo-Philipp Wich: fix ordering, move addpattern change into separate commit] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: Add support for Netgear WNR2000v1Huan Truong2016-12-142-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the WNR2000v1 board with 4MB flash, and produces device-specific factory, rootfs, and sysupgrade files for the WNR2000v1. This board is errorneously claimed as supported on the OpenWRT wiki as AP81, but AP81 image would not work because of APT81 image requiring having 8MB of flash, while WNR2000v1 has only 4MB. The image requires the u-boot bootloader to be modified to fuhry's bootloader first. Short specification: - CPU: Atheros AR9132 - 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps - 4 MB of Flash - 32 MB of RAM - UART header (J1) on board - 1x button Factory/Initial flash instructions: - Set up a TFTP server on your local machine. - Download the uImage for ar71xx-generic and the rootfs image for ar71xx-generic-wnr2000 and save in the tftp server root. - Gain serial access to the router via the UART port (telnetenable over the network only won't work!). - Upgrade the u-boot bootloader to fuhry's version by running the script: http://fuhry.com/b/wnr2000/install-repart.sh - When the router restarts, interrupt u-boot and gain access to u-boot command line. - Repartititon the board and flash initial uImage and rootfs as follow. Commands to type in u-boot: # tells u-boot that we have a tftp server on 192.168.1.10 setenv serverip 192.168.1.10 # tells u-boot that the router should take the address 192.168.1.1 setenv ipaddr 192.168.1.1 # erase the region from 0x050000-0x3f0000 erase 0xbf050000 +0x3A0000 # loads sqfs.bin on TFTP server, and put it to memory address 0x81000000 tftpboot 0x81000000 sqfs.bin # it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ # copy bit by bit 0xZZZZZZ bytes from offset 0x050000 cp.b 0x81000000 0xbf050000 0xZZZZZZ # same to the uImage.bin, write it right next to sqfs.bin # again, 0xYYYYYY is the length that tftpboot reports tftpboot 0x81000000 uImage.bin cp.b 0x81000000 0xbf2a0000 0xYYYYYY # We need to tell the kernel what board it is booting into, and where to find the partitions setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd" # Tell u-boot where to find the uImage setenv bootcmd "bootm 0xbf2a0000" # Tell u-boot to save parameters to the u-boot-env partitions saveenv # Reset the board reset Tested on: - WNR2000v1 board. - Initial flash works. Known bugs: - I don't know why factory image doesn't work on initial flash on stock firmware in u-boot recovery mode while it should. - Sysupgrade does not yet work, if you do -f it will mess up your installation (requiring a reinstall of sqfs and uImage). Signed-off-by: Huan Truong <htruong@tnhh.net>
* ar71xx: Add ath10k-firmware-qca988x for DomyWifi DW33DJing Lin2016-12-141-1/+1
| | | | | | | The default package selection was missing the correct FW for ath10k to work. Signed-off-by: Jing Lin <mumuqz@163.com>
* ar71xx: remove AP81 reference design board supportFelix Fietkau2016-12-122-8/+0
| | | | | | This board is very old and unlikely to still be relevant today. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP83 reference design board supportFelix Fietkau2016-12-122-9/+0
| | | | | | | | This board is very old and unlikely to still be relevant today. Support for it contains a significant amount of device specific baggage which is worth getting rid of. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for YunCore SR3200 and XD3200Piotr Dymacz2016-12-121-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: remove squashfs-64k rootfs image from bin directory, the generic one ↵Felix Fietkau2016-11-291-1/+0
| | | | | | is enough Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove split kernel/rootfs images where the sysupgrade image can be ↵Felix Fietkau2016-11-291-17/+1
| | | | | | written to flash directly Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove 2MB flash variant of WP543Felix Fietkau2016-11-292-7/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove legacy devices that cannot be supported due to kernel ↵Felix Fietkau2016-11-292-38/+0
| | | | | | partition size limits Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove legacy gzip imagesFelix Fietkau2016-11-291-6/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove obsolete jffs2 image building codeFelix Fietkau2016-11-292-27/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: move DomyWifi DW33D to nand subtargetPiotr Dymacz2016-11-242-11/+11
| | | | | | | | | This device uses NAND FLASH, so it should be kept in nand subtarget. Also, inlcude in packages kmod-usb-ledtrig-usbport instead of obsolete kmod-ledtrig-usbdev. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE830Piotr Dymacz2016-11-211-0/+8
| | | | | | | | | CPE830 is a clone of AP90Q, with different type of antenna (panel) and additional 4 LEDs for WiFi signal level indication. Use the same flash approach as for YunCore AP90Q. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE870Piotr Dymacz2016-11-211-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341. Short specification: - 535/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm - internal 14 dBi panel antenna - 8x LED, 1x button - UART (JP1) header on PCB Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. setenv bootcmd "bootm 0x9f020000" 5. saveenv && reset Vendor firmware access (login/password): Admin/5up Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore AP90QPiotr Dymacz2016-11-211-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2. Short specification: - 650/600/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz with external PA, up to 29 dBm - 2x internal 5 dBi omni antennas - 4x LED, 1x button - UART (JP1) header on PCB Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Flash instruction under vendor fimrware, using telnet/SSH: 1. Connect PC with 192.168.1.x address to WAN port 2. Power up device, enter failsafe mode with button (no LED indicator!) 3. Change root password and reboot (mount_root, passwd ..., reboot -f) 4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP 5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 6. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9f050000" - mtd erase firmware - mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E380AC v1 and v2Piotr Dymacz2016-11-211-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035. There are two versions of this model, with different RAM and U-Boot mtd partition sizes: - v1: 128 MB of RAM, 128 KB U-Boot image size - v2: 256 MB of RAM, 256 KB U-Boot image size Version number is available only inside vendor GUI, hardware and markings are the same. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 1x 10/100/1000 Mbps Ethernet, with PoE support - 128 or 256 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm - 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm - 6x internal antennas - 1x RGB LED, 1x button - UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB - external watchdog (Pericon Technology PT7A7514) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530NPiotr Dymacz2016-11-211-1/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As we already have support for CF-E316N v2 and many devices from this vendor look similar, the support was included in existing mach-*.c file, with few cleanups and fixes. All 3 devices are based on Qualcomm/Atheros QCA9531 v2. COMFAST CF-E320N v2 is a ceiling mount AP with PoE support. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x RGB LED, 1x button - UART (J1), GPIO (J9) and USB (J2) headers on PCB - external watchdog (Pericon Technology PT7A7514) COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support. They seem to have different only the front panel. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, WAN with PoE support - 1x USB 2.0 (in CF-E520N covered by panel, available on PCB) - 32 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x LED, 1x button - UART (J1) headers on PCB Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partitionHenryk Heisig2016-11-161-2/+0
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for Buffalo BHR-4GRV2FUKAUMI Naoki2016-11-161-0/+21
| | | | Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
* ar71xx: fix DEVICE_TITLE for Ubiquiti UAP Outdoor+Matthias Schiffer2016-11-151-1/+1
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: generate region-coded factory images for TP-Link TL-WR841ND v11Matthias Schiffer2016-11-111-0/+3
| | | | | | | | The latest stock firmwares for US and EU regions have started checking the region code. Tested-by: Andreas Ziegler <ml@andreas-ziegler.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: fix kernel relocate stub parallel build issueFelix Fietkau2016-11-081-4/+5
| | | | | | Use per-kernel directory Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: tl-wpa8630: Fix kernel lenghtHenryk Heisig2016-11-081-1/+1
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: wpa8630: change board name to tl-wpa8630Henryk Heisig2016-11-081-12/+12
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: Add support to Powerline ac TP-Link WPA8630Henryk Heisig2016-10-311-0/+12
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for D-Link DAP-2695 rev. A1Stijn Tintel2016-10-271-0/+29
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
generated by cgit v1.1 at 2024-12-18 05:39:26 +0000