summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: adjust ew-dorin platform for LAN+WAN setupFelix Fietkau2014-02-281-2/+3
| | | | | | Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de> SVN-Revision: 39763
* ar71xx: fix failsafe acces on several devicesGabor Juhos2014-02-251-1/+35
| | | | | | | | | | | | | | The ar71xx platform always uses the eth0 interface to provide access to the device in failsafe mode. Due to this, failsafe access is broken on devices where the LAN ports are connected to the 'eth1' interface. Update the relevant script to correctly set the ifname variable for these devices. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39752
* kernel: update 3.10 to 3.10.32Gabor Juhos2014-02-233-4/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39707
* ar71xx: define status LED for the RB91x boardsGabor Juhos2014-02-232-0/+18
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39705
* ar71xx: rb91x: register GPIO LEDsGabor Juhos2014-02-231-0/+51
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39704
* ar71xx: rb91x: add SPI device for the serial shift registerGabor Juhos2014-02-232-3/+63
| | | | | | | | | | | | | The RB91x boards are using a serial shift register connected to the SPI bus to drive some of the LEDs. Rework the board setup code to register a SPI device for that. This makes it possible to use the 'spi-74x164' driver to control the device. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39703
* ar71xx/mikrotik: enable the 74x164 GPIO driverGabor Juhos2014-02-231-0/+1
| | | | | | | | | That will be used to drive the 74HC595 serial-in/parallel-out 8-bits shift register which can be found on some RouterBOARDs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39702
* ar71xx: improve platform device support in the gpio-74x164 driverGabor Juhos2014-02-231-0/+74
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39701
* ar71xx: rb91x-nand: rewrite to use GPIO APIGabor Juhos2014-02-233-115/+174
| | | | | | | | | Rewrite tha rb91x-nand driver to use GPIO API to modify the NAND control lines. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39700
* ar71xx: rb91x: register a gpio-latch platform deviceGabor Juhos2014-02-221-0/+21
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39699
* ar71xx/mikrotik: enable the GPIO latch driverGabor Juhos2014-02-221-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39698
* ar71xx: add a generic GPIO latch driverGabor Juhos2014-02-224-0/+256
| | | | | | | | It will be used for the Mikrotik boards. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39697
* ar71xx/mikrotik: enable small sector erase in the m25p80 driverGabor Juhos2014-02-221-0/+1
| | | | | | | | | | | The serial flash devices used on the ROuterBOARDs are supporting 4KiB erase blocks. Enable the small sector erase option in the m25p80 driver to avoid superfluous erase/write of adjacent blocks. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39696
* ar71xx: spi-ath79: fix initial GPIO CS line setupGabor Juhos2014-02-222-2/+39
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39695
* ar71xx: refresh unaligned access hacks patchGabor Juhos2014-02-221-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39694
* ar71xx: rb91x: fix pll_1000 value for eth0 to avoid packet lossGabor Juhos2014-02-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | When the RB91x device uses a GbE link the connection suffers from packet loss: root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 20 -q PING 192.168.1.254 (192.168.1.254): 65507 data bytes --- 192.168.1.254 ping statistics --- 20 packets transmitted, 9 packets received, 55% packet loss round-trip min/avg/max = 4.570/4.815/4.999 ms Using a different PLL value fixes the issue. root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 100 -q PING 192.168.1.254 (192.168.1.254): 65507 data bytes --- 192.168.1.254 ping statistics --- 100 packets transmitted, 100 packets received, 0% packet loss round-trip min/avg/max = 4.449/5.413/13.870 ms Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39642
* ar71xx: Add support for MikroTik RB951Ui-2HnDGabor Juhos2014-02-202-4/+85
| | | | | | | | | | | | | | | | | | | | | | | | I noticed that the patch at http://patchwork.openwrt.org/patch/4017/ for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been abandoned because it wasn't generated and sent to the mailing list correctly and doesn't apply as a result. I have cleaned up this patch. When testing this on real hardware, I also noticed that wireless didn't work, so this patch fixes that as well. This patch applies cleanly to SVN 39392. Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com> Patchwork: http://patchwork.openwrt.org/patch/4773/ [juhosg: - drop the 'rb951ui_wlan_init' function and rework the code to use the recently introduced rb95x_wlan_init function instead, - fix GPIO number of the port5 LED, - rename LEDs according to the standard LED naming conventions, and use 'rb' prefix in the names] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39641
* ar71xx: add profile and build image for TP-Link TL-WDR4900 v2.0 boardGabor Juhos2014-02-192-0/+12
| | | | | | | | Patch-by: TenNinjas <tenninjas@tenninjas.ca> Patchwork: http://patchwork.openwrt.org/patch/4850/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39637
* ar71xx: add user-space support for TP-Link TL-WDR4900 v2.0 boardGabor Juhos2014-02-195-2/+12
| | | | | | | | | | | Patch-by: TenNinjas <tenninjas@tenninjas.ca> Patchwork: http://patchwork.openwrt.org/patch/4849/ [juhosg: - use the Archer C7 specific LED setup instead of adding identical code] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39636
* ar71xx: add kernel support for the TP-Link TL-WDR4900 v2.0 boardGabor Juhos2014-02-192-4/+50
| | | | | | | | | | | | Patch-by: TenNinjas <tenninjas@tenninjas.ca> Patchwork: http://patchwork.openwrt.org/patch/4848/ [juhosg: - rename and refresh kernel patch, - merge the board setup code into mach-archer-c7.c and drop mach-tl-wdr49000-v2.c] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39635
* ar71xx: fix unaligned access hacks for tcp timestampsGabor Juhos2014-02-181-1/+2
| | | | | | | | | | | | This missing bit of the hack saves hugely on instruction traps on tcp connections to ar71xx based routers. Patch-by: Dave Taht <dave.taht@bufferbloat.net> Patchwork: http://patchwork.openwrt.org/patch/4905/ [juhosg: adjust subject, refresh kernel patch] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39626
* ar71xx: WNR2200: fix mounting root fs problemGabor Juhos2014-02-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Solves ticket #14356 <https://dev.openwrt.org/ticket/14356> Without this patch, UART output will show only 4 partitions: [ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.750000] Creating 4 MTD partitions on "spi0.0": [ 0.750000] 0x000000000000-0x000000050000 : "u-boot" [ 0.760000] 0x000000050000-0x000000070000 : "u-boot-env" [ 0.770000] 0x000000070000-0x0000007f0000 : "firmware" [ 0.790000] 0x0000007f0000-0x000000800000 : "art" and then linux complains :VFS: Cannot open root device "(null)" With this patch, UART out will show 7 partitions: [ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.750000] Creating 4 MTD partitions on "spi0.0": [ 0.750000] 0x000000000000-0x000000040000 : "u-boot" [ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.770000] 0x000000050000-0x0000007f0000 : "firmware" [ 0.780000] 2 netgear-fw partitions found on MTD device firmware [ 0.780000] 0x000000050000-0x00000014b440 : "kernel" [ 0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.800000] 0x00000014b440-0x0000007f0000 : "rootfs" [ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.820000] mtd: device 4 (rootfs) set to be root filesystem [ 0.830000] 1 squashfs-split partitions found on MTD device rootfs [ 0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data" [ 0.840000] 0x0000007f0000-0x000000800000 : "art" This patch is tested against r39502 of trunk. Signed-off-by: Jonathan Chang <changcs@santos.ee.ntu.edu.tw> Patchwork: http://patchwork.openwrt.org/patch/4870/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39625
* ar71xx: fix mtdpartsize macro in image Makefile (#14961)Jo-Philipp Wich2014-02-131-1/+1
| | | | | | | | | | | | | The mtdpartsize macro triggers shell errors on various Linux distributions when the partname argument $(1) does not appear within the partmap $(2). Change the sed pattern to only emit anything if a successful substitution occured and only evaluate the arithmetic expression if something was printed by the sed program. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 39583
* ar71xx: dragino2: add missing sysupgrade support.Gabor Juhos2014-01-302-0/+4
| | | | | | | | | | | | | | The original dragino2 board support was missing some changes from the upstream svn repository (http://svn.dragino.com/dragino2) that supported sysupgrade. [juhosg: change subject] Signed-off-by: Karl Palsson <karlp@remake.is> Patchwork: http://patchwork.openwrt.org/patch/4801/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39429
* ar71xx: wpe72: set active_low flag for the reset buttonGabor Juhos2014-01-261-0/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39401
* ar71xx: wp543: set active_low flag for the buttonsGabor Juhos2014-01-261-0/+2
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39400
* kernel: update 3.10 to 3.10.28Gabor Juhos2014-01-263-6/+6
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39399
* ar71xx: image: reserve 4 erase blocks on the TP-Link devicesGabor Juhos2014-01-251-0/+6
| | | | | | | | | This ensures that the generated images will have enough erase blocks for JFFS2. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39397
* ar71xx: archer c7: define LEDs connected to the AR8327 switchGabor Juhos2014-01-251-0/+10
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39395
* ar71xx: image: move WNDAP360 macroGabor Juhos2014-01-251-3/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39394
* ar71xx: fix bad RX sensitivity on newer TL-WDR4300 boardsGabor Juhos2014-01-241-0/+6
| | | | | | | | | | | | | On recent TL-WDR4300 boards the external LNAs of the 2.4GHz interface are connected to GPIO lines. Because these GPIO lines are disabled by default, the RX sensitivity of the device is quite bad. Setup the GPIOs of the external LNAs to fix the issue. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39392
* ar71xx: image: generate sysupgrade images for the Compex boardsGabor Juhos2014-01-241-2/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39391
* ar71xx: add sysupgrade support for the Compex boardsGabor Juhos2014-01-241-1/+24
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39390
* ar71xx: image: use a single firmware partition on Compex devicesGabor Juhos2014-01-241-4/+10
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39389
* ar71xx: enable MTD_SPLIT_LZMA_FW optionGabor Juhos2014-01-241-0/+1
| | | | | | | | It will be used for Compex devices. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39388
* ar71xx: image: detect partition sizes in the Image/Build/Ath macroGabor Juhos2014-01-241-27/+30
| | | | | | | | | Get the size of the mtd partitions directly from the MTD layout and remove the superfluous macro parameters. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39384
* ar71xx: image: fix size verification in the CatFiles macroGabor Juhos2014-01-241-5/+13
| | | | | | | | | | | | | | | The macro checks the size of the rootfs image even if the second parameter of the macro contains the size of an eraseblock. It is wrong because the size of the kernel image will be adjusted to the next eraseblock and the resulting image might be too large. Fix the macro to check the size of the final image instead of the rootfs image. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39383
* ar71xx: ap83: define mtd layout via command lineGabor Juhos2014-01-232-1/+46
| | | | | | | | | Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39379
* ar71xx: ap81: define mtd layout via command lineGabor Juhos2014-01-232-1/+51
| | | | | | | | | Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39378
* ar71xx: image: show size limit in warning messagesGabor Juhos2014-01-231-2/+2
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39376
* ar71xx: add initramfs image support for Compex devicesGabor Juhos2014-01-231-0/+11
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39375
* ar71xx: wp543: use KEY_RESET code for the sw4 buttonGabor Juhos2014-01-231-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39374
* ar71xx: create wndr3700 network config from uci-defaultsLuka Perkov2014-01-233-97/+40
| | | | | | | | | Since that was the last configuration in defconfig directory we can drop the defconfig init script too. Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 39373
* ar71xx: mynet-n750: define LEDs connected to the AR8327 switchGabor Juhos2014-01-211-0/+15
| | | | | | | | Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4743/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39361
* ar71xx: tl-wr1043nd-v2: define LEDs connected to the AR8327 switchGabor Juhos2014-01-201-0/+10
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39346
* ar71xx: tl-wdr4300: define LEDs connected to the AR8327 switchGabor Juhos2014-01-201-0/+10
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39345
* ar71xx: set default LED config for the RB2011* boardsGabor Juhos2014-01-201-0/+10
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39344
* ar71xx: set status_led for the RB2011* boardsGabor Juhos2014-01-201-0/+5
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39343
* ar71xx: fix indentation in diag.shGabor Juhos2014-01-201-3/+3
| | | | | | | | Replace the leading spaces with tabs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39342
* ar71xx: rb2011: define LEDs connected to the AR8327 switchGabor Juhos2014-01-201-0/+16
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39341
generated by cgit v1.1 at 2024-08-15 13:26:23 +0000