summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx/config-3.10
Commit message (Collapse)AuthorAgeFilesLines
* brcm47xx: activate high mem for mips74k in the configHauke Mehrtens2014-08-071-0/+1
| | | | | | | | It is still not working. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 42054
* brcm47xx: add CONFIG_LEDS_GPIO_REGISTERHauke Mehrtens2014-07-021-0/+1
| | | | | | | | CONFIG_LEDS_GPIO_REGISTER is selected by the bcm47xx arch code. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41488
* brcm47xx: add new led and button supportHauke Mehrtens2014-01-121-0/+1
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39252
* brcm47xx: b44: This updates the phylib patches to the version send upstreamHauke Mehrtens2013-12-261-0/+1
| | | | | | | | This uses a fixed phy instead of a dummy one. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39166
* brcm47xx: deactivate early printk supportHauke Mehrtens2013-12-151-2/+1
| | | | | | | | | This breaks some devices where the serial console is not at port 0 but somewhere else. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39060
* brcm47xx: config: set CONFIG_HZ=100 and CONFIG_IP_ROUTE_VERBOSEHauke Mehrtens2013-12-011-4/+0
| | | | | | | | | This sets both values to the OpenWrt default values. There is no reason to use some brcm47xx specific values here. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38978
* brcm47xx: add vectored interruptsHauke Mehrtens2013-12-011-0/+1
| | | | | | | | | This adds support for vectored interrupts in this SoC. This is supported by the 74K cpus. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38975
* brcm47xx: register ADM6996L switchHauke Mehrtens2013-11-091-0/+1
| | | | | | | | | | | | This patch makes it possible to use adm6996.c on first generation BCM47XX devices with ADM switches. This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for the device. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38699
* brcm47xx: activate ARP daemon supportHauke Mehrtens2013-10-131-1/+0
| | | | | | | | This just add some bytes to the kernel and is activated on other targets. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38388
* brcm47xx: update early printk patchesHauke Mehrtens2013-10-061-1/+3
| | | | | | | | | | Early printk was disabled because it caused hangs on some devices, the old patches were using the CFE console now we use the normal serial console, it is at a constant address. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38309
* kernel: b53: add Register Access Bridge Registers (SRAB) interfaceHauke Mehrtens2013-09-251-0/+1
| | | | | | | | The SRAB interface is used on BCM4707 and BCM5301X SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38198
* brcm47xx: Add support for Huawei E970Hauke Mehrtens2013-09-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Huawei E970 wireless gateway devices. It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV. E960/B970 should work too, from what I know it's basically the same hardware. The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem. It uses a hardware watchdog which needs GPIO-7 to be toggled at least every 1-2 seconds. This patch uses gpio_wdt module (see my previous patch today) to take care of this. Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset button, image to be used for upgrade from OEM firmware's web interface Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970> Issue: * lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog reset during kernel decompress. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> SVN-Revision: 38011
* brcm47xx: add default config for new kernel config optionHauke Mehrtens2013-09-121-0/+1
| | | | SVN-Revision: 37958
* kernel: move CONFIG_NET_IP_TUNNEL to genericJonas Gorski2013-07-191-1/+0
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 37465
* brcm47xx: use b53 phy driver for the switch in kernel 3.10Hauke Mehrtens2013-07-141-0/+5
| | | | | | | | | | This makes it possible to use swconfig to controll the switch. This was tested with devices using b43 and bgmac. This was not tested on devices using tg3. This does not support the adm switch used in some very old devices. SVN-Revision: 37304
* brcm47xx: add initial support for kernel 3.10Hauke Mehrtens2013-07-141-0/+152
SVN-Revision: 37287