summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx
Commit message (Collapse)AuthorAgeFilesLines
* brcm47xx: add detection for Linksys WRT54GS V1Hauke Mehrtens2013-11-091-1/+12
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38700
* brcm47xx: register ADM6996L switchHauke Mehrtens2013-11-093-3/+127
| | | | | | | | | | | | This patch makes it possible to use adm6996.c on first generation BCM47XX devices with ADM switches. This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for the device. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38699
* brcm47xx: fix detection of Asus RT-N12B1 and Netgear WNR3500LHauke Mehrtens2013-11-051-1/+10
| | | | | | | | This closes #14367 and #14328. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38656
* kernel: update 3.10 to 3.10.18Gabor Juhos2013-11-051-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38652
* brcm47xx: b44: fix error handling for dummy phy creationHauke Mehrtens2013-10-251-24/+3
| | | | | | | | | When the mdio bus is unregistered the newly created phy will also be unregistered and freed. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38539
* brcm47xx: b44: add dummy phy device if we do not find anyHauke Mehrtens2013-10-251-0/+64
| | | | | | | | | | | On some devices with e.g. a BCM2535F switch the second MAC is used, but we can not find a phy under all addresses between 0 and 31, 0xffffffff is returned as phy id. If we can not find a phy at the expected address create a dummy one. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38538
* kernel: update 3.10 to 3.10.17Gabor Juhos2013-10-231-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38506
* brcm47xx: b44: detect external phy by bit set in DevControl registerHauke Mehrtens2013-10-228-73/+147
| | | | | | | | | | Without this patch we treated only phy addr 30 as an external phy, but there is a register to check that. Now we do not have to try to reset the switch to check for an external switch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38502
* brcm47xx: activate ARP daemon supportHauke Mehrtens2013-10-131-1/+0
| | | | | | | | This just add some bytes to the kernel and is activated on other targets. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38388
* kernel: update kernel to 3.10.15Hauke Mehrtens2013-10-131-1/+1
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38384
* brcm47xx: fix detection of some boardsHauke Mehrtens2013-10-131-0/+20
| | | | | | | | | | This adds some more boards. This fixes parts of #14316 and #14133. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38383
* brcm47xx: Cocci spatch "noderef"Hauke Mehrtens2013-10-071-0/+23
| | | | | | | | | | sizeof when applied to a pointer typed expression gives the size of the pointer. Found by coccinelle spatch "misc/noderef.cocci" Signed-off-by: Thomas Meyer <thomas@m3y3r.de> SVN-Revision: 38312
* brcm47xx: move clock detection patchesHauke Mehrtens2013-10-072-0/+31
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38311
* brcm47xx: move and rename nvram gpio patchHauke Mehrtens2013-10-061-0/+19
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38310
* brcm47xx: update early printk patchesHauke Mehrtens2013-10-067-116/+234
| | | | | | | | | | Early printk was disabled because it caused hangs on some devices, the old patches were using the CFE console now we use the normal serial console, it is at a constant address. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38309
* brcm47xx: update board detection patchesHauke Mehrtens2013-10-069-241/+227
| | | | | | | | | | | Add patches like they are currently in the mainline mips tree and add some more pending patches for board detection. * Now the board name is shown under machine in /proc/cpuinfo. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38308
* brcm47xx: b44: fix some problems with the phyHauke Mehrtens2013-10-069-354/+526
| | | | | | | | | | * do not try initialize a unused phy * some improvements to the phylib patch * do not turn the phy off when mac is off Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38306
* brcm47xx: add support for ipv6 in default network configHauke Mehrtens2013-10-021-58/+40
| | | | | | | | | Modify /etc/init.d/netconfig to use UCI defaults for building the default network config, which includes appropriate defaults for IPV6. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> SVN-Revision: 38294
* kernel: bgmac: move other bgmac patches to genericHauke Mehrtens2013-10-021-189/+0
| | | | | | | | The bgmac driver will be used on the brcm47xx and the bcm53xx target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38289
* kernel: bgmac: move bgmac patches already applied in mainline kernel to genericHauke Mehrtens2013-10-025-247/+0
| | | | | | | | | | The bgmac driver will be used on the brcm47xx and the bcm53xx target. These are only the patches already applied in current net-next/master branch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38288
* kernel: update 3.10 to 3.10.13Gabor Juhos2013-09-271-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38228
* kernel: b53: add Register Access Bridge Registers (SRAB) interfaceHauke Mehrtens2013-09-251-0/+1
| | | | | | | | The SRAB interface is used on BCM4707 and BCM5301X SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38198
* brcm47xx: b44: bgmac: some small changes to the phylib patchesHauke Mehrtens2013-09-182-38/+24
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38044
* brcm47xx: bgmac: b44: add support for Byte Queue LimitsHauke Mehrtens2013-09-184-10/+106
| | | | | | | | | This adds support for Byte Queue Limits in bgmac and b44, now it is possible to use more advanced network queue control algorithms. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38038
* brcm47xx: update the clock fixes for BCM5354Hauke Mehrtens2013-09-182-5/+36
| | | | | | | | | This updates the patches for BCM5354 to the version send for upstream Linux inclusion. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38037
* brcm47xx: update board detection patchesHauke Mehrtens2013-09-184-26/+221
| | | | | | | | | | This is now the version which was send for mainline Linux kernel inclusion. The data needed to detection a board is now stored in init data. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38036
* brcm47xx: add detection for Linksys E900 V1Hauke Mehrtens2013-09-181-2/+4
| | | | | | | | Thank you Rafał for the data. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38035
* brcm47xx: Add support for Huawei E970Hauke Mehrtens2013-09-164-1/+121
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Huawei E970 wireless gateway devices. It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV. E960/B970 should work too, from what I know it's basically the same hardware. The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem. It uses a hardware watchdog which needs GPIO-7 to be toggled at least every 1-2 seconds. This patch uses gpio_wdt module (see my previous patch today) to take care of this. Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset button, image to be used for upgrade from OEM firmware's web interface Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970> Issue: * lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog reset during kernel decompress. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> SVN-Revision: 38011
* brcm47xx: add detection for Phicomm M1Hauke Mehrtens2013-09-161-2/+5
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38009
* brcm47xx: detect Linksys E1200 V2Hauke Mehrtens2013-09-161-2/+4
| | | | | | | | | | This adds detection for Linksys E1200 V2 Thank you Lightsword and Rafał. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38006
* brcm47xx: mtd: bcm47xxpart: detect "factory" partitionHauke Mehrtens2013-09-161-0/+31
| | | | | | | | | A new type of partition with magic FCTY was found on Huawei E970: 46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290| Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 38005
* brcm47xx: bgmac: implement unaligned addressing for DMA rings that support itHauke Mehrtens2013-09-162-6/+146
| | | | | | | | | | | | | This is important patch for new devices that support unaligned addressing. That devices suffer from the backward-compatibility bug in DMA engine. In theory we should be able to use old mechanism, but in practice DMA address seems to be randomly copied into status register when hardware reaches end of a ring. This breaks reading slot number from status register and we can't use DMA anymore. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 38004
* brcm47xx: add detection code for Huawei E970Hauke Mehrtens2013-09-151-2/+5
| | | | | | | | | This is based on a patch by Mathias Adam. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38001
* kernel: update 3.10 to 3.10.12Gabor Juhos2013-09-152-9/+9
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38000
* brcm47xx: bgmac: allow bigger et_swtype nvram variableHauke Mehrtens2013-09-151-0/+14
| | | | | | | | | | Without this patch it is impossible to read et_swtype, because the 1 byte space is needed for the terminating null byte. Now it should be possible to read decimal and hex vars of max 8 bit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37999
* brcm47xx: mtd: bcm47xxpart: detect block aligned Squashfs partitionHauke Mehrtens2013-09-151-0/+40
| | | | | | | | | | | | | | | | | | Most of the bcm47xx devices use TRX format for storing kernel and some partition like Squashfs or JFFS2. This is pretty flexible solution, CFE (the bootloader) just writes (and later boots) TRX at some hardcoded place and paritions can vary in the size. However some devices don't use TRX format. Very recently we have discovered ZTE H218N that has kernel and rootfs partitions at some "random" places. This patch allows Linux find a rootfs partition after installing custom image with a CFE bootloader. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 37998
* brcm47xx: update board detection patchHauke Mehrtens2013-09-151-98/+142
| | | | | | | | | * Use different structs depending on the number of nvram variables to check. * Add detection of ZTE H218N, this closes #14151. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37996
* brcm47xx: bgmac: fix internal switch initializationHauke Mehrtens2013-09-151-0/+33
| | | | | | | | | | | | | Some devices (BCM4749, BCM5357, BCM53572) have internal switch that requires initialization. We already have code for this, but because of the typo in code it was never working. This resulted in network not working for some routers and possibility of soft-bricking them. Use correct bit for switch initialization and fix typo in the define. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 37993
* brcm47xx: detect Asus RT-N10Hauke Mehrtens2013-09-141-2/+4
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37989
* brcm47xx: tg3: use the phy address from et0phyaddr and not the default phy ↵Hauke Mehrtens2013-09-142-14/+227
| | | | | | | | | | address. Thank you Devastator for testing. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37986
* brcm47xx: board detection, GPIO for Linksys E1000 V2.1Hauke Mehrtens2013-09-131-2/+4
| | | | | | | | | | | | | | This patch adds board detection for the Linksys E1000 V2.1 router, as well as GPIO support for same. This fixes bug #14135. Currently, wired networking isn't working on the router, and I haven't tried the wireless, but with this patch, OpenWRT successfully boots, and all the LEDs and buttons work properly. Signed-off-by: Zachary Catlin <zcatlin@indiana.edu> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37977
* brcm47xx: detect WRT310NV1Hauke Mehrtens2013-09-131-2/+4
| | | | | | Thanks Devastator for testing SVN-Revision: 37969
* brcm47xx: remove support for kernel 3.8Hauke Mehrtens2013-09-1258-7852/+2
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37959
* brcm47xx: add default config for new kernel config optionHauke Mehrtens2013-09-121-0/+1
| | | | SVN-Revision: 37958
* kernel: update bcma and ssb to wireless-testing master-2013-09-09Hauke Mehrtens2013-09-121-5/+5
| | | | SVN-Revision: 37957
* brcm47xx: add me as maintainerHauke Mehrtens2013-09-071-0/+1
| | | | SVN-Revision: 37916
* kernel: update 3.10 to 3.10.10Gabor Juhos2013-09-021-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 37890
* kernel: update 3.10 to 3.10.9Gabor Juhos2013-08-232-2/+2
| | | | | | | | Also refresh 3.10 patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 37832
* brcm47xx: fix typo in Broadcom-bgmac-b43 profile nameHauke Mehrtens2013-08-171-1/+1
| | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37803
* brcm47xx: change board detection for some Asus devicesHauke Mehrtens2013-08-042-4/+24
| | | | | | | | This closes #13316 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37680
generated by cgit v1.1 at 2024-12-28 16:26:15 +0000