| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26876
|
|
|
|
|
|
| |
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26875
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
I wrote a patch to add 96348SV board (aka MAGIC) support to trunk.
In my case I've found it in a Telsey "Alice W-Gate" router, fairly common
(in the past) in Italy.
I used the board definition (GPIOs, leds, ...) from the Broadcom GPL-2
relased code (here is a mirror: http://beghiero.myftp.org/sorgenti/boardparms.c )
Thanks to KanjiMonster for the support on the IRC channel.
Signed-off-by: Laurento Frittella <laurento.frittella@gmail.com>
SVN-Revision: 25584
|
|
|
|
|
|
|
|
| |
The device is called SPW500V, not SP500W.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 25431
|
|
|
|
|
|
|
|
| |
devices that need it.
Signed-off-by: Daniel Dickinson <daniel@cshore.neomailbox.net>
SVN-Revision: 24836
|
|
|
|
|
|
| |
96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network.
SVN-Revision: 24442
|
|
|
|
|
|
| |
the reference design 96348GW so we use fixup to allow us to define the correct ones, also the GW6000 has no GPIO-controlled leds.
SVN-Revision: 24305
|
|
|
|
|
|
| |
not the generic 96348GW. Another commit will add the GW6200 specific boardid and leds. This removal reverts the 96348GW leds to the reference design GPIOs.
SVN-Revision: 24302
|
|
|
|
|
|
| |
indication led, and preinit interface
SVN-Revision: 24276
|
|
|
|
|
|
| |
(4-port switch)
SVN-Revision: 24273
|
|
|
|
|
|
|
|
|
|
| |
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24190
|
|
|
|
|
|
|
|
|
|
|
|
| |
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24188
|
|
|
|
|
|
|
|
|
|
|
| |
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24187
|
|
|
|
|
|
|
|
|
|
| |
Currently eth1 is hardcoded as the expected interface switches in diagmode.
This patch replaces the eth1 with the ifname, and also directly tests if
the interface specified by ifname has a switch attached.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24186
|
|
|
|
|
|
|
|
|
|
|
| |
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24185
|
|
|
|
|
|
| |
left on, not off
SVN-Revision: 22466
|
|
|
|
|
|
| |
and leds on preinit
SVN-Revision: 22465
|
|
|
|
|
|
| |
switch on eth1 (currently only 96348GW - Tecom 6x00)
SVN-Revision: 21629
|
|
|
|
|
|
| |
support it and for which /lib/brcm63xx.sh has the definitions (currently only 96348GW - Tecom 6x00)
SVN-Revision: 21628
|
|
|
|
| |
SVN-Revision: 21627
|
|
|
|
|
|
| |
6x00)
SVN-Revision: 21626
|
|
|
|
|
|
| |
state from userspace
SVN-Revision: 16892
|
|
|
|
| |
SVN-Revision: 16887
|
|
|
|
| |
SVN-Revision: 15900
|
|
SVN-Revision: 13362
|