summaryrefslogtreecommitdiff
path: root/target/linux/ipq806x/config-4.14
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: Limit NR_CPUS to 2Rosen Penev2018-06-181-1/+1
| | | | | | | | | | | ipq806x is all dual core processors. ipq807x is quad core. Removes this from dmesg: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit fff65dbe2436351ea1feee6c79110971ec4d5881)
* ipq806x: cleanup kernel configRam Chandra Jangir2018-05-241-14/+8
| | | | | | | | | | | Disable MSM8960, MSM8974 and APQ8084 - since these are different SoC's than IPQ806x Removed unrequired serial configs - since ipq806x uses SERIAL_MSM only Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> (cherry picked from commit 7ac6697fe269e7915e2dd55ba872cffcc102338b)
* ipq806x: add kernel 4.14 supportRam Chandra Jangir2018-05-241-0/+502
- Rebased the patches for 4.14 - Dropped spi-qup and 0027, 0028, 0029 clk patches since it's already included in upstream. Tested on IPQ AP148 Board: 1) NOR boot and NAND boot 2) Tested USB and PCIe interfaces 3) WDOG test 4) cpu frequency scaling 5) ethernet, 2G and 5G WiFi 6) ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> (cherry picked from commit 93dd2f7211db6607184adadb488582e01fd5c29b)