summaryrefslogtreecommitdiff
path: root/target/linux/lantiq/base-files
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: rework VG3503J imageMathias Kresin2016-10-191-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the new image build code and remove the lzma loader. The lzma loader was used to cheat the signature validation of the bootloader and I found another way to do this. To migrate boards already using LEDE/OpenWrt to the new image the following steps need to be done once: VR9 # run reset_uboot_config VR9 # reset VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000 VR9 # saveenv VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin VR9 # erase 0xb0020000 $(filesize) VR9 # cp.b 0x81000000 0xb0020000 $(filesize) The mac address is printed on the label at the bottom of the case. The following steps are need to be done during first install: VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000 VR9 # saveenv VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin VR9 # erase 0xb0020000 $(filesize) VR9 # cp.b 0x81000000 0xb0020000 $(filesize) The image uses the uImage firmware splitter now instead of hardcoded kernel and rootfs partitions. The firmware partition size was extended to use flash space that was reserved for partitions required only by the ECI firmware. Due to the changes an upgrade to a later LEDE revision from a running LEDE is supported now. A default switch config was added and the device uses the same MAC addresses as the ECI firmware now instead of the same for all VG3503J. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use wpad-mini for WBMR boardsMathias Kresin2016-10-151-16/+0
| | | | | | | | | | The WBMR boards are the only ones in the whole tree selecting the wpad and hostapd-utils package by default. Remove the wps uci-default script as well, there is no obvious reason why the wps config need to be set only for this board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix lantiq-dsl output spamMathias Kresin2016-10-111-1/+1
| | | | | | | | | | | | | | | | | In case the adsl/vdsl service is disabled intentional, the output is cluttered with the following message multiple times if the status of the dsl line is queried: killall: vdsl_cpe_control: no process killed If the dsl line status is queried by LuCI, the logfile is spammed with the message. Fix the issue by using killall in quite mode. In quite mode killall still returns a non-zero value if the to be killed process can not be found so that existing logic based on the return value still works. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use aliases device tree node for ledsMathias Kresin2016-10-051-1/+1
| | | | | | The chosen node is clearly the wrong place for aliases. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: cleanup led handling functionsMathias Kresin2016-10-053-19/+22
| | | | | | | | | Use a more generic name for the lantiq_get_dt_led_chosen function. Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led function can be used to achieve the same. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: board.d: apply alphabetical order to led fileMathias Kresin2016-10-051-12/+12
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: remove bad local shell variable declarationsJo-Philipp Wich2016-09-241-6/+1
| | | | | | | Local variable declarations outside of functions are illegal since the Busybox update to v1.25.0, therfore remove them from the appropriate places. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* lantiq: do not "local" variables outside of a functionMartin Blumenstingl2016-09-242-5/+5
| | | | | | | | | Older busybox versions allowed using the local keyword outside of functions, whereas 1.25.0 (which was introduced in 06fa1c46fc32) do not allow this anymore (leading to the following error when executing the script: "file: local: line nn: not in a function"). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* cleanup ucidef_set_interface* usageMathias Kresin2016-09-101-2/+2
| | | | | | | | - quote the interface name - remove call of not existing function - remove the proto if it's the default proto Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: board.d: apply alphabetical orderMathias Kresin2016-09-101-43/+43
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: board.d: cleanup default switch configMathias Kresin2016-09-101-32/+19
| | | | | | | | | | | | | | | | Add or fix the physical port number of switch ports to allow LuCI to display the ports in physical order. Remove the physical port number in case bridge port and physical port order are the same. Reorder the ucidef_add_switch parameter to be aligned with the switch port number. Remove board settings which are covered by the default case and remove comments. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: generate switch configuration for BTHOMEHUBV2B.Sigurd Hogsbro2016-08-201-1/+8
| | | | | | | Split from HH3A as it appears to have a different switch. https://en.wikipedia.org/wiki/BT_Home_Hub#Models_and_technical_specifications Signed-off-by: Sigurd Hogsbro <sigurd@hogsbro.org>
* lantiq: board.d: set lan mac address only where necessaryMathias Kresin2016-08-101-16/+8
| | | | | | | Do not set the lan mac address for boards which having the lan mac address already set in device tree source file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix switch configuration for EASY80920Hauke Mehrtens2016-07-281-0/+7
| | | | | | | | The device tree description misses some Ethernet ports and there was no model specified for this board. In addition there was no switch specific default configuration created. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: fix WBMR-300HPD switch port assignmentFelix Fietkau2016-07-281-4/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: fix network in failsafeMathias Kresin2016-06-221-9/+1
| | | | | | | | | | So far the network in failsafe is setup only for one board. Use the eth0 interface as lan interface for all boards for now. If a board has its lan interface(s) on another eth, a special handling based on the board name can be added. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add support for ARV7506PW11 (Alice/O2 IAD 4421)Oswald Buddenhagen2016-06-223-1/+12
| | | | | | | | | | | | | | | | | | Ethernet, ADSL2+ and LEDs are fully functional. Supporting the two TAE ports and SIP gateway was not attempted. The WiFi is unreliable, due to experimental support for rt35xx family devices by the rt2800pci driver. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de> [rebase to LEDE HEAD] [switch to normal image instead of brnboot image] [remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out] [remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT] [enable usage of the wireless LED] [fixup mac address configuration] Sgned-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: remove gr7000 supportJohn Crispin2016-06-221-4/+0
| | | | | | this seems to have never worked as the wrong SoC is selected Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: diag - switch off the power led on failsafeMathias Kresin2016-06-201-0/+4
| | | | | | | | | | | | | | This patch is a follow up to commit 4cf3fd4 "add support for indicating the boot state using three leds". At the time of writing the patch, I wasn't aware that it's possible to switch info failsafe after boot (factory reset). Enabling the failsafe led without disabling the running led causes an unexpected led colour on devices using a single multicolour led to indicate the boot state. Signed-off-by: Mathias Kresin <dev@kresin.me>
* Revert "lantiq: Use correct macaddr generating logic for the DGN3500"Felix Fietkau2016-06-151-5/+0
| | | | | | | This reverts commit 492964e741f1e0254b6ed7c0a095551a31d25dc9, which makes no sense. /etc/board.d cannot be used for system init stuff. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: add ARV4525PW wifi ledJohn Crispin2016-06-141-0/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: fix fritz7320 wifi supportJohn Crispin2016-06-141-0/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: add AVM image mageic to sysupgrade scriptJohn Crispin2016-06-131-0/+2
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: Add Support for Fritz!Box 7360 SLJohn Crispin2016-06-131-0/+5
| | | | | Signed-off-by: Sebastian Ortwein <krone@animeland.de> Tested-by: Guido Lipke <lipkegu@gmail.com>
* lantiq: add default lan setup to board.d scriptJohn Crispin2016-06-131-0/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: add Buffalo WBMR-300HPD supportFelix Fietkau2016-06-112-0/+14
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: Use correct macaddr generating logic for the DGN3500Daniel Gimpelevich2016-05-271-0/+5
| | | | Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* lantiq: VGV7519 - add vlan supportMathias Kresin2016-05-271-1/+2
| | | | | | Add the lantiq,switch property to enable vlans and setup them up. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix ARV4518PWR01 networkMohammed Berdai2016-05-271-0/+4
| | | | | | | | This patch fixes the missing Lan interface config in the file /etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan being down and therefore no way to access the router unless via UART-TTL. Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
* image / basefiles: make console password configurableJohn Crispin2016-04-181-1/+1
| | | | | Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: Fix typo in LED diag script.John Crispin2016-04-261-1/+1
| | | | | | | Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> Acked-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 49242
* lantiq-dsl: add missing blank in dsl outputJohn Crispin2016-04-091-1/+1
| | | | | | | | blank inserted before ACTATP Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com> SVN-Revision: 49137
* lantiq-dsl: bugfix latency values swapped for lucistatJohn Crispin2016-04-091-2/+2
| | | | | | | | swapped wrong latency output Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com> SVN-Revision: 49136
* lantiq-dsl: bugfix db negative sign after commaJohn Crispin2016-04-091-1/+1
| | | | | | | | If db is negative minus sign was shown after comma Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com> SVN-Revision: 49135
* lantiq: print profile name in dsl lucistatFelix Fietkau2016-03-071-0/+1
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48949
* lantiq: do not set default firmware fileFelix Fietkau2016-03-071-1/+1
| | | | | | | | | We are now shipping a DSL firmware, do not set it by default to some file name. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48941
* use "-gt" instead of ">" with [ in /lib/functions/lantiq_dsl.shJohn Crispin2016-02-121-2/+2
| | | | | | | | | Avoids inadvertent file creation when executing `/etc/init.d/dsl_control status`. Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net> SVN-Revision: 48700
* lantiq: add support for TP-Link VR200vHauke Mehrtens2016-01-181-0/+7
| | | | | | | | | This adds basic support for TP-Link VR200v. Currently the following parts are not working: FXO, Voice, DECT, WIFI (both) Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48328
* lantiq: fix VDSL device detection with Linux 4.4Felix Fietkau2016-01-181-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48319
* lantiq: match default xdsl mode and default wan interfaceJohn Crispin2016-01-011-1/+5
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48047
* lantiq: convert vendorid into human readable formJohn Crispin2016-01-011-0/+67
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48046
* lantiq: add the current profile to the stats outputJohn Crispin2016-01-011-0/+30
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48045
* lantiq: use devicename:colour:function led naming schemeJohn Crispin2016-01-011-4/+4
| | | | | | | | | | | | | | | | The leds of the following boards are not renamed due to lack of manuals/informations: - ARV7519PW - ARV7510PW22 - ARV4510PW The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't match the leds from the manual or pictures (e.g. there shouldn't be a wps led). Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48042
* lantiq: add support for indicating the boot state using three ledsJohn Crispin2016-01-012-54/+16
| | | | | | | | | | | | | | The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to indicate the current boot state. This patch adds support for such cases. The existing led sequences should be the same as before. Boards which are using a led different from power (like TDW89x0) are changed to switch of the led after boot Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48041
* lantiq: use dsl led defined in DTSJohn Crispin2016-01-012-15/+18
| | | | | | | | | | | | | | | | | dsl_control (dsl_notify.sh) is the only process which is aware of the state of the atm/ptm interface. Use the dsl led exclusive for the dsl line state. On boards which don't have a distinct internet and a dsl led, let the netdev status of the atm interface trigger the shared led. Triggering the shared led according to the status of the ppp interface isn't suitable, since the led would be switched of if the ppp connection goes down, but the line is still in sync. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48040
* lantiq: use power leds defined in DTSJohn Crispin2016-01-011-15/+19
| | | | | | | | Use the power leds defined in the dts file instead of hardcoded led names. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48039
* lantiq: use default leds defined in DTSJohn Crispin2016-01-012-20/+23
| | | | | | | | | | | | | Remove all now double defined leds from the led board file. Use pppoe as default for all broadband connections, since it's the default in OpenWrt now. Rename the the wifi leds to make sure, the not applicable default values get overwritten. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48038
* lantiq: BTHOMEHUBV2B - remove missing usb led workaroundJohn Crispin2016-01-011-1/+0
| | | | | | | | The workaround shouldn't be in the default configuration. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48032
* lantiq: Fix LED handling.John Crispin2015-12-171-24/+32
| | | | | | | | | | - Use common OpenWrt blink patterns instead of custom ones - Add preinit_regular hook - Handle the TDW89X0 that does not have a configurable power LED Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> SVN-Revision: 47914
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-112-2/+2
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
generated by cgit v1.1 at 2024-11-01 14:46:51 +0000