summaryrefslogtreecommitdiff
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Added Onion Omega2 and Omega2+Lazar Demin2017-01-153-0/+214
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io) Specifications: - SoC: MediaTek MT7688AN (580MHz, ramips) - Omega2 - RAM: 64MB DDR - Storage: 16MB NOR SPI flash onboard - Omega2+ - RAM: 128MB DDR - Storage: 32MB NOR SPI flash onboard + microSD slot - Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter - Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port - Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock) - All Docks Provide: - Micro-USB port to provide power to the Omega - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial - USB 2.0 socket connected to Omega - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide: - Omega GPIO breakout - Allows for connection of Omega Expansions: - Ethernet Expansion - Relay Expansion - PWM Expansion - OLED Expansion - Ethernet Expansion - Proto Expansion - Cellular Expansion Signed-off-by: Lazar Demin <lazar@onion.io>
* ramips: fix WLI-TX4-AG300N boot and networkYo Abe2017-01-131-2/+11
| | | | | | | | | | | | | | | | Partition label "linux" prevents the root file system to be mounted at boot time leading to a kernel panic. After changing it to "firmware", the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data" are correctly recognized. The attached IP175C 10/100 MBit switch cannot connect to a link with fixed 1000Mbit speed. The correct link speed is 100MBit. The switch is detected and can be configured via mdio bus and should allow two separable VLANs to be configured for the 4 available ports. Signed-off-by: Yo Abe <abe.geel@gmail.com> [picked from openwrt/PR#330] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for VoCore2Andrew Yong2017-01-131-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: MiWiFi Nano fixesL. D. Pinney2017-01-021-11/+29
| | | | | | | | | | | | | | | | Use the the dt-bindings macros and add the reset button. Set the correct polarity for the LEDs and drop the default state. Remove all trigger for the LEDs. According to the manual the LEDs are only used to show the operation state, where blue means normal operation. Use the MAC-Addresses stored in EEPROM for the ethernet and the wireless interface. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use leds only for boot status indication, add proper commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use new image build code for more devicesMathias Kresin2016-12-2414-10/+24
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use different board names for variantsMathias Kresin2016-12-2410-6/+20
| | | | | | | | | | | | Use different names for flash size related board variants, to make sure that only images for the actual flash size are considered as valid by the image validation code. Remove the flash size suffix from the string returned by ramips_board_detect() to ensure that existing scripts relying on the former used boardname are still working. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use D-Link DIR-600 B1 image for B2 versionMathias Kresin2016-12-241-107/+0
| | | | | | | Everything set for the B1 is identical to the values uses for the B2 version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use destinct 11AC NAS board nameMathias Kresin2016-12-243-14/+28
| | | | | | | | | | Use a distinct board name even if the board is near to identical to the WeVO W2914NS v2. To make sure that a 11AC NAS image can not be installed on a WeVO W2914NS v2, both board need to use different names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support to TP-Link Archer MR200Henryk Heisig2016-12-221-0/+195
| | | | | | | | | | CPU: MT7620N 580MHz Flash: 8MB RAM: 64MB build-in modem 3G/4G four ethernet port 10/100Mbps Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for ZyXEL Keenetic Omni / Omni IIVitaly Chekryzhev2016-12-222-0/+240
| | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: adding registration for si3210Giuseppe Lippolis2016-12-201-0/+13
| | | | | | | | | | | | | | | The si3210 is a SLIC device providing a complete analog telephone interface and therefore frequently used in soho router. The si3210 have a native spi interface to be controlled by the CPU but currently there is no dedicated driver in lede. Adding a registration for this device in spidev allow to control the device in user space. This way of patching is also in line with the rationale of the spidev driver, see: http://marc.info/?t=148145791900001&r=1&w=2 The si3210 has been also added in the DWR-512 DT to properly describe the HW. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: WNDR3700v5 fix mtd partitions and radiosL. D. Pinney2016-12-201-6/+7
| | | | | | | Fix the mtd partition layout and enable both radios in the dts Tested-by Andrius Štikonas <andrius@stikonas.eu> Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* ramips: fix PBR-D1 button definitionBangLang Huang2016-12-041-2/+2
| | | | | | | Due to the product specification, the button on PBR-D1 should be reset, not wps. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: introduce CONFIG_PCI and CONFIG_OF_*PCI for rt288xTobias Wolf2016-12-043-4/+12
| | | | | | This is a prerequisite for F5D8235 V1 to use PCI based OHCI/EHCI. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: improve F5D8235 V1 supportTobias Wolf2016-12-041-16/+69
| | | | | | | | | | | | | | | | | | | This fixes the partition name for the firmware splitter, the cfi address and adds the mtd-eeprom address for wmac. It adds additional LEDs and make use of them in diag.sh and 01_leds. Please note that the ":blue:wired" LED is used because the ":blue:router" behaviour is unpredictable for failsafe indication. The issue with the router LED is that you have two states only. "off" is steady on and "on" blinks. Therefore the wired LED is more suitable. Furthermore it reuses the correct switch configuration definition to reflect the device ports and numbering. Additionally fixes the issue that the default configuration is not applied as no port 6 exists on this device. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: RB750Gr3: Add pwr LED and buzzer to DTSAndrew Yong2016-12-011-1/+12
| | | | | | | | | use pwr LED in diag.sh Expose unused pinmux pins as GPIOs export power LED and buzzer pins Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr Signed-off-by: Andrew Yong <me@ndoo.sg>
* treewide: fix button keys codes used in dtsMathias Kresin2016-11-277-7/+7
| | | | | | Use keycodes that matches the intended use case based on the label. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add missing chunked-io directive to W2914NSV2.dtsiYong-hyu, Ban2016-11-261-0/+1
| | | | | | | | | Fix bug that LEDE failed to boot with this message: WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214 mt7621_spi_transfer_one_message+0x28c/0x620() Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
* ramips: SamKnows SK-WB8 DTS cleanupAndrew Yong2016-11-261-11/+6
| | | | | | Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000). Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: Add device DLINK DWR-512-BGiuseppe Lippolis2016-11-231-0/+128
| | | | | | | | | | | | | | | | | | | | | | The Dlink DWR-512-B modem is a ralink 5350 processor based embedding a 3G mini-pcie router. The oem JBOOT bootloader has to be replaced by a RT5350 SDK U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot configured for the RT5350 256MiB SDR. Main reason to change the bootloader is the encrypted header used to store the kernel image. In this way an image can only be generated using the propietary binboy tool (included in the GPL distribution from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs partition scheme. This is considered a big constraint (limited kernel size and inefficient usage of flash space). For interested people I pubblished the details of my investigation about the encrypted firmware header here: http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: cleanup dts files of mt7621 based boardsMathias Kresin2016-11-2320-184/+130
| | | | | | | | | | | | | | | | | | | | Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci in mt7621.dtsi and enable the nodes in the indiviual board dts files. The nodes require further device specific configuration anyway. Remove the m25p80@0 spi child node from mt7621.dtsi and add the chunked-io parameter to the individual board dts files. Fix the spi flash compatible string for the WNDR3700V5. Drop the mt7621-eval-board compatible string for all boards which are not the eval board. Drop the linux,modalias parameter from spi flash node. Remove the xhci node from board files, it is already enabled in dtsi. Disable xhci for boards not having usb ports populated. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for WeVO W2914NS v2perillamint2016-11-213-0/+141
| | | | Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
* ramips: add support for ZyXEL Keenetic VivaVitaly Chekryzhev2016-11-181-0/+154
| | | | | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [removed linux,modalias parameter from flash node in dts] [removed sdhci node from dts; no sd card slot here] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Sitecom WLR-6000Jasper Scholte2016-11-171-0/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the file is way to big for only including a kernel. The factory image need to have the dlf file extension. Otherwise the Sitecom firmware rejects the file. The stock firmware uses the following mac addresses: LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr) 2,4: 00:0C:F6:AA:BB:D8 (EEPROM) 5: 00:0C:F6:AA:BB:DC (EEPROM) WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr) Assuming the mac address range :D8 to :DC is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: 2.4GHz: 00:0C:F6:AA:BB:D8 LAN: 00:0C:F6:AA:BB:D9 WAN: 00:0C:F6:AA:BB:DA 5 GHz: 00:0C:F6:AA:BB:DC The first MAC is assigned to the 2.4GHz WiFi interface to keep compatibility with the SSIDs printed on the case, which have the last three sextets of the MAC address appended. There are still issues with the rt2x00 driver. It is not possible to use both wireless interfaces at the same time. The 2.4 GHz wireless (PCIe) only works if the internal 5GHz wireless is/has been enabled or used for scanning. The internal 5GHz wireless only works if the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz after it was enabled will result in stations seeing the 5Ghz AP but are unable to connect. Due to the not optimal working wifi the manufacture, backup and storage partitions of the OEM firmware are kept for now to allow an easy switch back to the Sitecom firmware. Signed-off-by: Jasper Scholte <NightNL@outlook.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Digineo AC1200 ProDominik Menke2016-11-171-0/+15
| | | | | | This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash. Signed-off-by: Dominik Menke <dom@digineo.de>
* ramips: cleanup ZBT-WG3526.dtsiDominik Menke2016-11-171-6/+6
| | | | | | | | - replace magic numbers with GPIO_* constants - replace generic PCI definitions with correct vendor and device identification Signed-off-by: Dominik Menke <dom@digineo.de>
* ramips: split ZBT-WG3526.dts into dtsi and dts filesDominik Menke2016-11-172-112/+120
| | | | Signed-off-by: Dominik Menke <dom@digineo.de>
* treewide: dts: use keycode defines from input dt-bindingMathias Kresin2016-11-13168-337/+673
| | | | | | | | | | | | | | | | | | | | | All compiled device tree files not mentioned are binary identical to the former ones. Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts. Due to the include of the input binding header, the BTN_* node names in: - ramips/GL-MT300A.dts - ramips/GL-MT300N.dts - ramips/GL-MT750.dts - ramips/Timecloud.dts will be changed by the compiler to the numerical equivalent. Move the binding include of lantiq boards to the file where they are used the first time to hint the user where the values do come from. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: dts: use C style includesMathias Kresin2016-11-123-3/+3
| | | | | | | No functional change but allows me to use one script to compile all device tree source files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: dts: fix dtc compiler warningsMathias Kresin2016-11-122-0/+6
| | | | | | | | | | | Fixes invalid device tree parameters. Drop the mvsw61xx node used in mvebu device tree source files. It looks like some kind of ethernet switch cargo cult. Neither the marvell,88e6352 nor the marvell,88e6172 compatible strings can be found in any LEDE file or in the kernel sources. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add TEW-691GR/TEW-692GR 2.4 GHz interface mac addressesMathias Kresin2016-11-092-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Assign an unused MAC addresses to the 2.4GHz wifi interface as it was originally planed but not possible. The MAC address numbering of the TEW-691GR changes to the following pattern: LAN: AA:BB:CC:DD:EE:0C WIFI: AA:BB:CC:DD:EE:0D WAN: AA:BB:CC:DD:EE:0F The MAC address numbering of the TEW-692GR changes to the following pattern: LAN: AA:BB:CC:DD:EE:e4 WAN: AA:BB:CC:DD:EE:e5 2.4GHz: AA:BB:CC:DD:EE:e7 5 GHz: AA:BB:CC:DD:EE:e8 Set the label and compatible string for the TEW-692GR PCIe wireless according to the the PCI binding documentation. Use the wifi@0,0 label and the pci0,0 compatible string since the PCI vendor and device id is unknown. It should work anyway since the compatible string isn't evaluated (yet). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use the ralink,mtd-eeprom device tree propertyMathias Kresin2016-11-096-19/+23
| | | | | | | | | | | | | | | | | | | | | Use the ralink,mtd-eeprom instead of invoking the userspace firmware loader. Set the label and compatible string according to the the PCI binding documentation. Use the wifi@0,0 label and the pci0,0 compatible string in case the PCI vendor and device id is unknown. It should work anyway since the compatible string isn't evaluated (yet). This commit might fixes the PCIe wireless for the Buffalo WHR-600D. This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug script but never had the correct eeprom name set to trigger the firmware from flash extraction. Use the usual eeprom for the soc wmac of the Dovado Tiny AC. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support for Wavlink WL-WN575A3Roger Pueyo Centelles2016-11-081-0/+130
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug wireless router with the following specifications: - CPU: MediaTek MT7628AN 580MHz - Flash: 8MB - RAM: 64MB - Ethernet: 2x 10/100 Mbps (switched) - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm - Antennas: 4x external (2 per radio), non-detachable - LEDs: 4 programmable + LAN, WAN, POWER - Buttons: reset, WPS Flashing instructions: Factory U-boot launches a TFTP client if WPS button is pressed during power-on. Rename the sysupgrade file and configure a TFTP as follows: - Client (WL-WN575A3) IP: 192.168.10.101 - Server IP: 192.168.10.100 - Filename: firmware.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for MikroTik hEX v3 (RB750Gr3)Andrew Yong2016-11-021-0/+121
| | | | | | | | | | | | | | The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz). RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot. Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware. The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices. A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware. Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: Archer C50 cleanupHenryk Heisig2016-10-311-16/+47
| | | | | | | | | | | - setting read-only flag to important partitions - enabling PA to improve 2.4 GHz signal strength - add missing leds - rename colour led - add mac adress to 5GHz wlan interface - included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h> Signed-off-by: Henryk Heisig hyniu@o2.pl
* ramips: fix PSG1218 LEDsXuefu Lin2016-10-261-3/+3
| | | | Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips: add support for Planex VR500.YuheiOKAWA2016-10-151-0/+92
| | | | | | | | | | | | SOC: MT7621A RAM: 256MiB NOR: MX25L51245G Non Wireless Router. Issue: soft reboot problem. SPI Flash do not exit 4byte address mode. Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
* ramips: use rfkill for wps button on wlan only boardsMathias Kresin2016-10-156-8/+8
| | | | | | | | | | | | | All of the touched boards don't have an ethernet port. Allow to use the wps button on these boards to enable the wireless radio after boot. The force enabled wireless for the DCH-M225 is removed. It is reckless to bring up an unencrypted wireless network by default these days. Using the wps button to bring up the radio seam to me the better approach. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use rootfs splitter and new image build code for BR-6475NDMathias Kresin2016-10-151-5/+0
| | | | | | | Use the edimax uImage splitter instead of the fixed size rootfs partition. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: improve edimax 6200n/nl supportMathias Kresin2016-10-152-9/+14
| | | | | | | | | | Assign the reset functionality to the wps/reset buttons. Use the wlan switch of the 6200n to enable/disable wlan. Add the internet led of the 6200nl and use the led for boot status indication Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix edimax 6200nl switch configMathias Kresin2016-10-151-1/+1
| | | | | | | | | | | | | With 3a9752bbd2bc00e407b5dcad21789720f40abf0e and later changes to ramips_set_preinit_iface() the default vlan config applied during preinit was changed. These changes were made without updating the default network config to ensure that vlan interfaces used for lan/wan are still configured. Fix the issue by using the default all LAN portmap and disabling not connected switch ports using portdisable device tree parameter. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Zyxel NBG-419N2 (WAP3205v2)Klaus2016-10-041-0/+117
| | | | | | | | | | | applied bb-final-ramips-add-zyxel-nbg-419n2.patch from 123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65; see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905, modified slightly to fit to CC release and to new lede build system: image/rt305x.mk include file is used now changed NBG-419N2.dts format to fit style of other dts files Signed-off-by: Klaus <k-laus@quantentunnel.de>
* ramips: Add support for Phicomm K2 PSG1218Xuefu Lin2016-10-041-0/+118
| | | | | | | | | - CPU: MT7620A 580MHz - Flash: 8MB - RAM: 64MB - External PA+LNA on both WLAN2.4 and WLAN5 - 4x LAN ethernet and 1x WAN ethernet Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips : add support for Newifi D1BangLang Huang2016-09-271-0/+149
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips : add support for PandoraBox D1BangLang Huang2016-09-271-0/+159
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: Add support for ZBT-CPE102Cezary Jackiewicz2016-09-271-0/+118
| | | | | | | | | | - CPU: MT7620N 580MHz - Flash: 8MB - RAM: 64MB - build-in minipcie slot for modem 3G/4G - one ethernet port 10/100Mbps Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: add support for Mercury MAC1200R v2Daniel Golle2016-09-091-0/+94
| | | | | | | | MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM reset button GPIO is still missing (anyone?) bootloader password is 'slp' Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: TEW-691GR: fix switch and wirelessMathias Kresin2016-08-201-1/+4
| | | | | | | | | Due to the missing phy-mode setting, the switch wasn't initialised. The wireless requires an eeprom to work. Use the same mac addresses as the stock firmware. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: TEW-692GR: fix switch and wirelessMathias Kresin2016-08-201-1/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AR8327 initvals were not copied to the DTS during the switch from mach file to device tree and broke the switch on the device. The former used PORT6 related initvals were wrong and have been corrected. The phy mode setting for the switch was missing in the DTS as well. The wireless requires an eeprom to work. The dual band wireless chips have both bands enabled by default but only one band per chip is working. The stock firmware uses the following mac addresses: LAN: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 5 GHz: AA:BB:CC:DD:EE:E8 Assuming the mac address range :E4 to :E8 is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: LAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E5 5 GHz: AA:BB:CC:DD:EE:E8 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: rt3883: fix dtc compiler warningMathias Kresin2016-08-201-0/+2
| | | | | | | | | | Fixes the following compiler warning: Warning (reg_format): "reg" property in /ethernet@10100000/port@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) Warning (avoid_default_addr_size): Relying on default #address-cells value for /ethernet@10100000/port@0 Warning (avoid_default_addr_size): Relying on default #size-cells value for /ethernet@10100000/port@0 Signed-off-by: Mathias Kresin <dev@kresin.me>