summaryrefslogtreecommitdiff
path: root/target/linux/ramips/mt7621
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Add I2C driver to the default kernel configRosen Penev2017-01-151-0/+2
| | | | | | | | | | I made a commit that added the RTC driver to the kernel config with the intent that it would fix hctosys. Unfortunately while the RTC driver is in there, it's connected through I2C, the driver for which comes in module form and is thus loaded late. After this commit, it works fine. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: remove ubifs xz decompression supportFelix Fietkau2017-01-091-1/+0
| | | | | | | It has been unused, and less useful than squashfs for cases where flash space usage matters. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: Add RTC driver to kernel for working hctosysRosen Penev2016-10-311-0/+1
| | | | | | | Build the RTC driver into the kernel, (and remove the optional module), in order to make hctosys working. (Currently the module is loaded after hctosys has failed previously) Signed-off-by: Rosen Penev <rosenp@gmail.com>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-1/+1
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: fix wrong blocksizesMathias Kresin2016-09-151-1/+0
| | | | | | | | | | | | | | | | | | The D-Link DIR-860L B1 has a flash chip which doesn't support 4K sectors. Since the DIR-860L B1 was the only mt7621 board which had the 4k blocksize set, the 4K sector support is removed from the kernel config. I've checked the flash chips of all boards having set a 4K blocksize again. This time I searched harder to finding bootlogs instead of relying on wikis articles and/or the device tree source file. The Planex MZK-DP150N has an en25q32b instead of the mentioned one in the dts. Albeit the en25q32b supports 4K sectors, 4K support is not enabled in the driver. Change the blocksize for this board back to 64K. Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: enable 4K sector support in kernel configMathias Kresin2016-09-131-0/+1
| | | | | | | | | | | | This is a follow up to 28110727f1d513a6c4c13aa87ecb606aa5d306eb "ramips: set blocksize for 4MB devices". I've missed to include the required changes of the kernel configs to enable 4K sector size support. The option is only enabled for targets having boards with 4k sector size flash chips. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7621: switch to 24kcJonas Gorski2016-08-231-1/+1
| | | | | | | | 1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly the same and will generate identical code, so there is no need to tune to 1004kc instead of 24kc. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ramips: enable nand support for mt7621John Crispin2016-08-031-1/+1
| | | | | | this makes sysupgrade work on the ERX Signed-off-by: John Crispin <john@phrozen.org>
* build: remove MIPS dsp/dsp2 CPU_SUBTYPEFelix Fietkau2016-08-031-1/+0
| | | | | | | There does not seem to be any meaningful difference in generated code. This will save some time and space on snapshot builds Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: mt7621: add missing kernel symbolJo-Philipp Wich2016-07-161-0/+1
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: fix the number of uarts for each SoCÁlvaro Fernández Rojas2016-06-031-1/+2
| | | | | | | | - Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620. - Allow up to 3 uarts on MT7621 and MT7628. - Remove unneeded SERIAL_8250_RT288X for MT7628. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: set default profile to priority 1John Crispin2016-05-141-0/+1
| | | | | | doing so will sort all profiles alphabetically Signed-off-by: John Crispin <john@phrozen.org>
* ramips/mt7621: remove cflags overrideFelix Fietkau2016-05-141-1/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: convert mt7621 to new image building codeJohn Crispin2016-05-1211-199/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add initial support for SamKnows SK-WB8Andrew Yong2016-05-121-0/+18
| | | | Signed-off-by: Andrew Yong <me@ndoo.sg>
* target: globally remove ARCH_PACKAGES overridesJo-Philipp Wich2016-04-171-1/+0
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: Add support for the Netgear WNDR3700v5John Crispin2016-04-261-0/+17
| | | | | | | | | | https://wiki.openwrt.org/toh/netgear/wndr3700 wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49247
* ramips: Add support for ZBT WG3526John Crispin2016-04-211-0/+13
| | | | | | | | | | | | | | | | | | The WG3526 is the follow-up to the 2626 and is mostly the same, with the excaption that the mt7602 has been replaced with the mt7603. The internal wifi setup has also changed slightly. Based on my tests, everything that worked on the 2626 works on the 3526 and with roughly the same performance. v1->v2: * Remove some references to 2626 that I had missed in the dts. v2->v3: * Update patch to match new file structure. * Removed SD driver to be consistent with other MT7621 targets. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> SVN-Revision: 49213
* ramips: Disable the SD driver by default on MT7621John Crispin2016-04-094-4/+4
| | | | | | | | | | | | | | | | The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for months resulting in unbootable devices. Until it's fixed, disable it in the default profiles. Reports / Discussed here: https://dev.openwrt.org/ticket/21392 https://dev.openwrt.org/ticket/21834 https://dev.openwrt.org/ticket/21995 https://forum.openwrt.org/viewtopic.php?id=59092 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> SVN-Revision: 49131
* ramips: mt7621: fix Ubiquiti EdgeRouter X profileJohn Crispin2016-04-091-1/+2
| | | | | | | | Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware). Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49127
* ramips: mt7621: sync MQmaker WiTi profile name to dts nameJohn Crispin2016-04-091-3/+3
| | | | | | Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49126
* ramips: fix subtarget kernel version assignment (only mt7621 is ready for now)Felix Fietkau2016-03-071-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48953
* ramips: add linux 4.4 support, update mt7621 subtarget to 4.4Felix Fietkau2016-03-071-10/+13
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48951
* ramips: re-enable highmem support for MT7621 now that it's fixedFelix Fietkau2016-01-241-0/+3
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48469
* ralink: update config files to build the cleaned up ethernet driverJohn Crispin2015-12-171-4/+6
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47902
* ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)John Crispin2015-12-121-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-121-0/+4
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47875
* Revert "ramips: use gic timer as clocksource for mt7621"Felix Fietkau2015-12-111-4/+0
| | | | | | This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7. SVN-Revision: 47872
* ramips: add additional support for MQmaker WiTi boardJohn Crispin2015-12-111-0/+20
| | | | | | | | | | | | | | The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5 ghz antenna. This is the 6th submission that adds support for XHCI in the device tree file, along with switching the location of the 2 radio's and addition of the kmod-i2c-mt7621 in the default packages of the profile. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 47845
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-111-0/+4
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47843
* ramips: enable CPS for mt7621John Crispin2015-12-111-2/+6
| | | | | | | | | | | | | Enables CPS multiprocessing instead ob obsoleted CMP for mt7621. This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx: * iperf shows only 50Mbits on direct gigabit connection to desktop, * ping times jump to 5-6ms to dorectly connected desktop * /proc/interrupts shows spurious interrups (ERR) Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47842
* ralink: bump to the target to v4.3John Crispin2015-12-101-16/+25
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47831
* ralink: renable nand supportJohn Crispin2015-11-241-0/+1
| | | | | | | | CONFIG_MTK_MTD_NAND was incorrectly disabled by r47619. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47640
* ralink: add support for netis WF-2881John Crispin2015-11-242-1/+46
| | | | | | | | | | | | | | | | | | | | | | | | | netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN. It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. this device only works on top of UBI. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons (reset button) * ethernet switch and USB diag LEDs * UART * GPIOs * sysupgrade Tested and not working * failsafe Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 47619
* ramips: minor fixes for mt7621 profilesFelix Fietkau2015-11-072-4/+2
| | | | | | | | | * remove references to non-existing kmod-usb3-mt7621 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!) Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47407
* ramips: add support for ZBT WG2626John Crispin2015-11-021-0/+20
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47351
* ramips: Enable RTC support for PBR-M1Felix Fietkau2015-09-111-0/+1
| | | | | | | | | | | | | | The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself will not be build because CONFIG_RTC_CLASS is currently not enabled for its kernel. Enabling this option should fix the problem of the missing rtc device on these boards. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46857
* ramips: disable the openwrt commandline hackJonas Gorski2015-08-301-1/+0
| | | | | | | | We don't make use of it, so no need to have it enabled. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46759
* ramips: fix various mistakes in subtargets *.mk profilesJohn Crispin2015-08-173-10/+8
| | | | | | | | | | | | | | | | This patch: * fixes wrong indentation * fixes wrong names and descriptions (ex. Dlink -> D-Link) * changes filenames to manufacturer names * moves oem/unknown manufacturers boards to misc.mk profiles * combines profiles for boards from the same manufacturers in one file (ex. Olimex) * fix profile files structure (keep the same convention as in other targets, ex. ar71xx) in various .mk profiles, in ramips target. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46631
* ramips: add support for STORYLiNK SAP-G3200U3John Crispin2015-07-241-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN. It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons * ethernet switch and USB diag LEDs * UART * GPIOs Tested and not working: * LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?) * failsafe mode (known problem, needs workaround like other MTK based devices) More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46454
* ramips: enable mt76 by default for mt7621Felix Fietkau2015-07-184-3/+4
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 46410
* ramips: Add Support for the Linksys RE6500John Crispin2015-06-181-0/+16
| | | | | | | | | | This patch adds support for the Linksys RE6500 Range Extender http://wiki.openwrt.org/toh/linksys/re6500 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 46043
* ramips: add support for PandoraBox PBR-M1John Crispin2015-06-181-0/+22
| | | | | | | | | This patch is for PandoraBox PBR-M1 which is based on mt7621, all the features work fine, including rtc, leds, button, usb3.0, etc. Signed-off-by: tymon <banglang.huang@foxmail.com> SVN-Revision: 46041
* ralink: add missing symbolJohn Crispin2015-06-071-0/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 45918
* ramips: enable highmem support for mt7621Felix Fietkau2015-06-041-8/+4
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 45889
* ramips: diable ill_acc driver by defaultJohn Crispin2015-05-271-0/+1
| | | | | | | | this treacled down via the stable tree and wandered into 3.18.14 Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 45793
* ralink: mt7621 add ECHI OCHI XCHI supportJohn Crispin2015-03-261-0/+6
| | | | | | | | The usb stroage not working since updated 3.18. Porting from MTK's source code. Signed-off-by: wengbj <fl.service@t-firefly.com> SVN-Revision: 45021
* ralink: drop 3.14 supportJohn Crispin2015-03-161-206/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44811
* ralink: add missing symbol that broke full buildsJohn Crispin2015-03-101-0/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44642
* kernel: move KERNFS to generic configJohn Crispin2015-03-061-1/+0
| | | | | | | | KERNFS symbol is selected by SYSFS, so place it in generic config. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> SVN-Revision: 44615
generated by cgit v1.1 at 2024-12-12 10:58:17 +0000