summaryrefslogtreecommitdiff
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* This had been set in r44508 as a workaround for switch problems.Imre Kaloz2015-08-211-2/+1
| | | | | | | | | | | | | Now that the switch driver can handle two devices with the same MAC address in separate VLANs we can go back to using the same address on both interfaces. This is the Linksys firmware's default behavior. Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 46700
* Previously, all VLANs (port-based or 802.1q) were sharing a single database ↵Imre Kaloz2015-08-212-4/+19
| | | | | | | | | | | | | | | | in the ATU. This created problems in the case of a system where two ports/devices share a MAC address (e.g. Linksys WRT1900AC eth0/eth1). This also clears any bootloader-set FDB defaults. This had caused issues creating port-based VLANs when mappings overlapped previous VLANs. Packets destined to a port not in the default port group flooded all ports. Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC) Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 46699
* mvebu: fix cobra chainmaskImre Kaloz2015-08-211-2/+2
| | | | | | | | Thanks Sebastian for spotting it. Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 46697
* kernel: add missing symbols for 4.1Zoltan Herpai2015-08-201-0/+3
| | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> SVN-Revision: 46696
* mvebu: add support for the Linksys boot counterImre Kaloz2015-08-192-14/+20
| | | | | | | | | | | | | The u-boot boot counter was never reset after a successful boot, which sometimes could make some variables become out of sync. This patch adds support for the boot counter and enables auto_recovery unconditionally. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 46690
* at91: fix usb rate backport patch tab mangleJohn Crispin2015-08-171-14/+14
| | | | | | | | | The patch submitted in [46649] was mangled in the use of gmails webmail interface, tabs replaced with spaces, resulting in a patch which dit not apply. This should fix the issue, sorry for the noise. Signed-off-by: Ben Whitten <benwhitten@gmail.com> SVN-Revision: 46676
* orion: remove IRQF_DISABLEDJohn Crispin2015-08-171-2/+2
| | | | | | | | | | no-op since 2.6.35 removed in Kernel 4.1 see https://lwn.net/Articles/380931/ Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> SVN-Revision: 46672
* generic: crypto: remove IRQF_DISABLEDJohn Crispin2015-08-173-3/+3
| | | | | | | | | | no-op since 2.6.35 removed in Kernel 4.1 see https://lwn.net/Articles/380931/ Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> SVN-Revision: 46671
* lantiq: Support newer versions of the PEF7071 ethernet PHYsJohn Crispin2015-08-172-2/+2
| | | | | | | | | | The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's PHY driver (for his u-boot sources) already supports that PHY because it uses a PHY ID mask of 0xfffffff8. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46670
* oxnas: remove support for kernel 3.18 and 4.0John Crispin2015-08-1728-1554/+0
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 46668
* ramips: move patches aroundJohn Crispin2015-08-171-0/+0
| | | | | | | | 0073 needs to applied afert 0102 Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 46667
* ramips: base-files: optimize etc/diag.sh and etc/board.d/01_leds scriptsJohn Crispin2015-08-172-424/+235
| | | | | | | | | | | | | | | | | | | | | | | | Instead of using board name provided explicitly as text in LED name, ex.: [...] mlwg2) status_led="mlwg2:blue:system" [...] use $board variable, which allows to combine together multiple boards with same color and LED names, ex: [...] mlw221|\ mlwg2) status_led="$board:blue:system" [...] The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically. One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name"). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46665
* ramips: use consistent naming scheme for LEDsJohn Crispin2015-08-1780-612/+694
| | | | | | | | | | | | | The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach. The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target: * fixes wrong indentation * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body) * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files) * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46664
* ar71xx: add support for TP-Link TL-WDR6500 v2John Crispin2015-08-1711-1/+258
| | | | | | | | | | | Signed-off-by: Weijie Gao <hackpascal@gmail.com> This patch adds support for TP-Link TL-WDR6500 v2. The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for the whole firmware, so I have to create a new firmware creation method. SVN-Revision: 46663
* ar71xx: add 64kb bootloader mtd parser for tplinkpartJohn Crispin2015-08-171-6/+29
| | | | | | | | | | | Signed-off-by: Weijie Gao <hackpascal@gmail.com> This patch adds flash layout parser for TP-Link firmwares which have a 64kb bootloader. This is used for TP-Link TL-WDR6500 v2. SVN-Revision: 46662
* ramips: reorder the sysupgrade scriptJohn Crispin2015-08-171-13/+13
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 46660
* ramips: reorder patchesJohn Crispin2015-08-1711-5/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 46659
* ipq806x: switch AP148 to using SMEM based MTD parserJohn Crispin2015-08-1713-63/+35
| | | | | | | | | | | | | | *Enable SMEM MTD parser and its dependencies (SMEM & HW spinlocks) in the kernel config *Replaces the MTD layout in DT by the dynamic layout provided by the SMEM parser for AP148 Using the OF based parser is still possible on platforms which have a fixed MTD partition layout. Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> SVN-Revision: 46658
* ipq806x: add QCOM SMEM based MTD parserJohn Crispin2015-08-172-0/+554
| | | | | | | | | This patch adds a new parser which uses the SMEM available on IPQ and some other QCOM platforms to map the MTD partitions. Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> SVN-Revision: 46657
* ipq806x: add SMEM supportJohn Crispin2015-08-176-0/+1918
| | | | | | | | | | | | 2 patches are cherry-picked from the following LKML thread: *https://lkml.org/lkml/2015/4/11/208 The last patch (036-soc-qcom-add-smem-to-IPQ806x-platforms.patch) is adding the corresponding DT nodes required for IPQ806x. Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> SVN-Revision: 46656
* ipq806x: add hwspinlock supportJohn Crispin2015-08-1719-28/+958
| | | | | | | | | | | | | | This change cherry-picks the following 3 changes from linux-next: *fb7737 hwspinlock/core: add device tree support *19a0f6 hwspinlock: qcom: Add support for Qualcomm HW Mutex block *bd5717 hwspinlock: qcom: Correct msb in regmap_field We're also adding a patch to add the hardware spinlock device nodes on IPQ806x platforms (033-soc-qcom-Add-sfbp-device-to-IPQ806x-dts.patch). Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> SVN-Revision: 46655
* kernel: move linux, part-probe dt parsing in generic codeJohn Crispin2015-08-1718-53/+229
| | | | | | | | | | | | | | The "linux,part-probe" dts parsing is a pretty neat generic feature. It has been posted to kernel.org and could easily be reused by all targets. This change moves the patch to the 3.18 and 4.1 generic folders, and makes the feature available to all platforms who may want to use it. Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 46654
* ar71xx: Add support for Black SwiftJohn Crispin2015-08-1710-0/+172
| | | | | | | | | | | | Add support for the Black Swift board: http://www.black-swift.com/ Took relevant parts and slightly adapted from: https://github.com/blackswift/openwrt/blob/master/bsb.patch Signed-off-by: Bruno Randolf <br1@einfach.org> SVN-Revision: 46651
* at91: Backport determine_rate prototype fixJohn Crispin2015-08-171-0/+20
| | | | | | | | | | | | | This patch is backport of a fix to a USB prototype mismatch bug found in 3.18 kernels, originally submitted by Boris Brezillon [1]. The symptom of this bug was that devices attached to the at91 using at91_ohci on a hub never appeared and failed to initialise. [1] http://www.spinics.net/lists/linux-usb/msg125969.html Signed-off-by: Ben Whitten <ben.whitten@gmail.com> SVN-Revision: 46649
* mcs814x: use firmware partition splitter on dLAN USB ExtenderJohn Crispin2015-08-173-9/+5
| | | | | | | | | to avoid editing the dts every time the kernel size changes. uImage is now bigger than 1MB. Pad uImage to 64k erase block size. Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 46648
* mcs814x: fix interrupt handlingJohn Crispin2015-08-172-22/+27
| | | | | | | | | | Switch to generich chip irqs/irq domains. Interrupts were broken since kernel 3.14. dLAN USB extender is now booting again. Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 46647
* mcs814x: fix debug UARTJohn Crispin2015-08-172-3/+48
| | | | | | | | | | Switch to new 8250 debug uart code because the old mach-mcs814x/include/mach/debug-macro.S tries to include asm/hardware/debug-8250.S which no longer exists since kernel 3.14 Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 46646
* ramips: Fix MT7621 pinmux bits for uart3, uart2, mdioJohn Crispin2015-08-171-9/+26
| | | | | | | | | | | The MT7621 uses a 2 bit wide configuration of the sdhci, spi, mdio, pcie, wdt, uart2 and uart3 in the GPIO_MODE register. It was correctly done for sdhci, spi, pcie and wdt, The same has to be done for uart3, uart2 and mdio. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46645
* ramips: Fix amount of MT7621 pins controlled by spi groupJohn Crispin2015-08-171-1/+1
| | | | | | | | | The PINS conntrolled by the SPI bits in the GPIO_MODE register is always 7 and not 8 for nand mode. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46644
* ramips: Fix uart2/uart3 pinmux order on MT7621John Crispin2015-08-171-4/+4
| | | | | | | | | The uart3 setting in GPIO_MODE register is before the uart2 setting. Also don't mix uart2 and uart3 function/groups. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46643
* brcm2708: override disabled device tree module status from config.txtJohn Crispin2015-08-171-0/+6
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 46642
* brcm2708: fix kmod-sound-soc-iqaudio-dac and add missing symbolJohn Crispin2015-08-171-2/+6
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 46641
* brcm2708: update 4.1 patchesJohn Crispin2015-08-17147-244/+3456
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 46640
* brcm2708: use BuildDTB in image/MakefileJohn Crispin2015-08-171-1/+1
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 46639
* oxnas: switch to kernel 4.1John Crispin2015-08-171-1/+1
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 46637
* oxnas: prepare for kernel 4.1John Crispin2015-08-1715-1/+788
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 46636
* ramips: remove unnecessary LED declaration for WT1520 in diag.shJohn Crispin2015-08-171-3/+0
| | | | | | | | This device doesn't have defined LEDs in its dts file. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46635
* ramips: fix indentation, case statements structure and optimize ↵John Crispin2015-08-171-220/+170
| | | | | | | | | | | | | | | | | | | base-files/etc/board.d/02_network The following patch: * fixes wrong indentation * combines together boards with same configuration * removes unnecessary spaces * removes empty lines after ";;" and uses only "|\" (for consistency) * orders boards alphabetically in base-files/etc/board.d/02_network script. One bug was left untouched: freestation5 board is listed twice in case statement, in ramips_setup_macs(). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46634
* ramips: be consistent with case statement in base-files/lib/upgrade/platform.shJohn Crispin2015-08-171-117/+117
| | | | | | | | Always use "|\" (without spaces) and keep boards in alphabetical order. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46633
* ramips: remove leading spaces, sort boards and optimize base-files/lib/ramips.shJohn Crispin2015-08-171-217/+217
| | | | | | | | | | | | | | | | | | This patch: * fixes various mistakes (leading spaces, wrong or missing model names) * shortens model strings (we don't need to use whole model string from dts file, make it for consistency and as optimization) * sorts boards alphabetically in base-files/lib/ramips.sh script. Case statement was tested after above changes with simple script, which: * takes model string from dts{,i} file (model = "...") * provides this value as case input ($machine) * returns output ($name) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46632
* ramips: fix various mistakes in subtargets *.mk profilesJohn Crispin2015-08-1738-166/+141
| | | | | | | | | | | | | | | | This patch: * fixes wrong indentation * fixes wrong names and descriptions (ex. Dlink -> D-Link) * changes filenames to manufacturer names * moves oem/unknown manufacturers boards to misc.mk profiles * combines profiles for boards from the same manufacturers in one file (ex. Olimex) * fix profile files structure (keep the same convention as in other targets, ex. ar71xx) in various .mk profiles, in ramips target. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46631
* ramips: remove old code for Edimax BR-6524NJohn Crispin2015-08-174-25/+0
| | | | | | | | | It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing). This patch removes remaining code. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46630
* ramips: fix 7Links PX-4885 dts{, i}, board, image and profile namesJohn Crispin2015-08-179-19/+17
| | | | | | | | The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46629
* ramips: fix Buffalo WMR-300 dts, board, image and profile namesJohn Crispin2015-08-176-10/+10
| | | | | | | | The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46628
* ramips: fix Omnima models, images and profiles namesJohn Crispin2015-08-1710-47/+49
| | | | | | | | | | | | | | | | | | | | Official names for supported Omnima products are (as on website): * Omnima HPM * Omnima MiniEMBWiFi * Omnima MiniEMBPlug This patch changes: * board names * dts filenames * profile names * image filenames * LED names for Omnima devices, for consistency. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46627
* ramips: fix Edimax BR-6425 board nameJohn Crispin2015-08-173-3/+3
| | | | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46626
* ramips: fix Tenda W150M model nameJohn Crispin2015-08-171-2/+2
| | | | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46625
* ramips: fix Aigale Ai-BR100 dts and profile namesJohn Crispin2015-08-173-6/+6
| | | | | | | | The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46624
* ramips: fix Olimex models, images and profiles namesJohn Crispin2015-08-177-25/+25
| | | | | | | | | | | | | | Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website. The following patch: * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}" * changes filenames of dts and profile files * changes image filenames for Olimex RT5350F-OLinuXino{,-EVB} devices. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46623
* ramips: fix Sitecom WL-341v3 board and image namesJohn Crispin2015-08-174-15/+15
| | | | | | | | | | | | | The following patch changes: * board name from "wl341v3" to "wl-341v3" * dts filename * LED names in dts file for Sitecom WL-341v3 device. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46622
generated by cgit v1.1 at 2024-12-28 19:01:28 +0000