summaryrefslogtreecommitdiff
path: root/tools/firmware-utils/src
Commit message (Collapse)AuthorAgeFilesLines
* firmware-utils: tplink-safeloader: add more country codes for Archer C7 v4Dmitry Tunin2017-11-141-0/+7
| | | | | | | If codes do not match, it is impossible to flash from the stock firmware. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ar71xx: increase kernel partition size for TP-Link RE450 v1Piotr Dymacz2017-11-141-2/+2
| | | | | | | | | | | This increases kernel partition size and fixes rootfs (file-system) partition size on TP-Link RE450 v1. Also, while we are at it, switch from statically defined kernel and rootfs partitions in kernel cmdline to "tplink-fw" mtd splitter. Fixes: FS#1072. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: increase kernel partition size for some TP-Link boardsHenryk Heisig2017-11-141-8/+8
| | | | | | | | | | | | | | This patch increases kernel partition size and re-enables image generation for below TP-Link boards: - archer-c58-v1 - archer-c60-v1 - tl-wr902ac-v1 - tl-wr942n-v1 Signed-off-by: Henryk Heisig <hyniu@o2.pl> [commit message and title reworded] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for TP-Link TL-WR840N v5Robert Marko2017-11-081-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 4 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 1x LED (GPIO-controlled), 1x button * LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Orange LED is registered so you can later use it for your own purposes. Flash instruction: Unlike TL-WR840N v4 flashing through WEB UI works in v5. 1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image. 2. Go to 192.168.0.1 3. Flash the sysupgrade image through Firmware upgrade section of WEB UI. 4. Wait until green LED stops flashing and use the router. Notes: TFTP recovery is broken since TP-Link reused bootloader code for v4 and that does not take into account only 4 MB of flash and bricks the device. So do not use TFTP Recovery or you will have to rewrite SPI flash. They fixed it in later GPL code,but it is unknown which version of bootloader you have. After manually compiling and flashing bootloader from GPL sources TFTP recovery works properly. Signed-off-by: Robert Marko <robimarko@gmail.com>
* tools/firmware-utils: mktplinkfw* fix rootfs offsetThibaut VARÈNE2017-11-083-12/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With '-a' specified on the command line, the current code: - computes an aligned _kernel length_ instead of an aligned _rootfs offset_. - does not update the rootfs offset after computing the new kernel length, and instead retains the layout default. When the kernel length exceeds the available space left with this fixed offset, the resulting image header contains invalid data, with the recorded rootfs offset overlapping the kernel area. This patch ensures that rootfs offset is correctly computed and reflected in the final image. Furthermore, the build_fw() function special cases the rootfs_align option because of the above invalid logic. This is also fixed and the computed (or command-line provided, or layout-provided) rootfs_ofs value is used in all cases. There seems to be no valid reason to extend the kernel length beyond the actual length of the kernel itself (OFW images don't do it) so this part of the existing behavior is dropped. Example image before the patch: Kernel data offset : 0x00000200 / 512 bytes Kernel data length : 0x00158438 / 1410104 bytes Kernel load address : 0x00000080 Kernel entry point : 0x00000080 Rootfs data offset : 0x00140000 / 1310720 bytes Rootfs data length : 0x001e4f7e / 1986430 bytes Example image after the patch: Kernel data offset : 0x00000200 / 512 bytes Kernel data length : 0x001583fe / 1410046 bytes Kernel load address : 0x00000080 Kernel entry point : 0x00000080 Rootfs data offset : 0x00158600 / 1410560 bytes Rootfs data length : 0x001e4e22 / 1986082 bytes Tested-by: Mathias Kresin <dev@kresin.me> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Henryk Heisig <hyniu@o2.pl> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: add support for TP-LINK Archer C7 v4Felix Fietkau2017-10-191-0/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9561+QCA9888. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin and rename it to ArcherC7v4_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f040000 +$filesize 3. cp.b $fileaddr 0x9f040000 $filesize 4. reset Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/firmware-utils: mktplinkfw move build_fw() to libThibaut VARÈNE2017-10-064-148/+102
| | | | | | | | | | | | | | This patch moves build_fw() to mktplinkfw-lib.c The versions of mktplinkfw.c and mktplinkfw2.c had slight differences in code flow, the version from mktplinkfw.c has been preferred. While it's expected that this change will not affect mktplinkfw2, all use cases could not be tested and so this particular change is committed separately. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* tools/firmware-utils: mktplinkfw regroup duplicate codeThibaut VARÈNE2017-10-064-452/+274
| | | | | | | | | | | | | This patch carves out the duplicated code of mktplinfw.c and mktplinkfw2.c and moves it to mktplinkfw-lib.c This change is a semantic NOP (the code is unchanged). To ensure compatibility with gcc-5.x and newer without changing the code, -fgnu89-inline is added to the build flags for these two binaries. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* tools/firmware-utils: remove hardcoded values from mktplinkfw2.cThibaut VARÈNE2017-10-061-161/+24
| | | | | | | | | | | | This patch removes all the hardcoded board-specific values from mktplinkfw2.c, and as well as the corresponding support code. By design, this change also deletes all of the broken matching logic that was embedded in mktplinkfw2 and aligns the "inspect" behavior with that of mktplinkfw (i.e. print the parsed header content as they are without further processing). Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: add support for TP-Link Archer C20 v1Maxim Anisimov2017-09-131-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v1 is a router with 5-port FE switch and non-detachable antennas. It's very similiar to TP-Link Archer C50. Also it's based on MediaTek MT7620A+MT7610EN. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 8x LED (GPIO-controlled*), 2x button, power input switch - 1 x USB 2.0 port * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the blue part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Factory image notes: These devices use version 3 of TP-Link header, fortunately without RSA signature (at least in case of devices sold in Europe). The difference lays in the requirement for a non-zero value in "Additional Hardware Version" field. Ideally, it should match the value stored in vendor firmware header on device. We are able to prepare factory firwmare file which is accepted and (almost) correctly flashed from the vendor GUI. As it turned out, it accepts files without U-Boot image with second header at the beginning but due to some kind of bug in upgrade routine, flashed image gets corrupted before it's written to flash. So, to flash this device we must to prepare image using original firmware from tp-link site with uboot. Flash instruction: Until (if at all) TP-Link fixes described problem, the only way to flash LEDE image in these devices is to use tftp recovery mode in U-Boot. There are two ways to flash the device to LEDE: 1) Using tftp mode with UART connection and original LEDE image - Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp server directory - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, power up the router and press key "4" to access U-Boot CLI. - Use the following commands to update the device to LEDE: setenv serverip 192.168.0.66 tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin erase tplink 0x20000 0x7a0000 cp.b 0x80060000 0x20000 0x7a0000 reset - After that the device will reboot and boot to LEDE 2) Using tftp mode without UART connection but require some manipulations with target image - Download and unpack TP-Link Archer C20 v1 firmware from original web site - Split uboot.bin from original firmware by this command (example): dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1 - Create ArcherC20V1_tp_recovery.bin using this command: cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin - Place ArcherC20V1_tp_recovery.bin in tftp server directory. - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. - Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* tools/firmware-utils: mktplinkfw2: allow parameter overrideThibaut VARENE2017-09-091-9/+7
| | | | | | This patch enables commandline override of board hw_ver and hw_ver_add Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* tools/firmware-utils: document reserved fields in mkchkimgThibaut VARENE2017-08-031-4/+18
| | | | Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* firmware-utils: mktplinkfw2: respect -e option when reading fw infoRafał Miłecki2017-07-311-3/+5
| | | | | | | | When -e option it specified a corresponding flag is set in the custom_board. By using custom_board as fallback -e option gets respected for unknown boards. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mktplinkfw2: fix info for images with LE kernel LA/EPRafał Miłecki2017-07-311-1/+7
| | | | | | | With this change endianness is also respected when reading firmware info. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mktplinkfw2: replace "endian_swap" field with "flags"Rafał Miłecki2017-07-311-8/+10
| | | | | | This will allow adding more similar tricks needed by other hardware. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: tplink-safeloader: add support for TP-Link RE350Alex Maclean2017-07-251-0/+41
| | | | Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* firmware-utils: drop mktplinkfw-kernel toolPiotr Dymacz2017-07-221-352/+0
| | | | | | | As we can now use combined mode in "mktplinkfw" tool to generate the same header/image, this tool is no longer needed. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: mktplinkfw: rework combined image optionPiotr Dymacz2017-07-221-58/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | We use combined option in "mktplinkfw" tool for generating initramfs kernel images and header for kernel inside "safeloader" image type (in fact, only for TL-WR1043ND v4 at this moment). There is also "mktplinkfw-kernel" tool, a stripped-down version, used only for generating "simple" header, for safeloader image types. This changes how "mktplinkfw" handles combined images (which then will allow us to drop the stripped-down version of the tool): - drop "ignore size" command line option (it was used only for combined images anyway) - don't require "flash layout id" for combined images (we don't need and shouldn't limit size of the initramfs kernel and for kernels inside safeloader images, the "tplink-safeloader" tool does the size check) - require kernel address and entry point in command line parameters for combined images (consequence of previous point) - don't include md5 sum and firmware length values in header (they are needed only for update from vendor GUI and are ingored in case of initramfs and "tplink-safeloader" images) - drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to match introduced changes in "mktplinkfw" tool. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: tplink-safeloader: add support for TL-WR902AC v1 USPiotr Dymacz2017-07-221-1/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: tplink-safeloader: fix Archer C60 factory imageHenryk Heisig2017-07-091-2/+0
| | | | | | | | This commit fixes build factory image for TP-Link Archer C60v1. Size of partition "SupportList" is only 256 bytes, and can contain only 3 entries. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* firmware-utils: mktplinkfw2: use static board struct for custom valuesRafał Miłecki2017-07-081-18/+15
| | | | | | | | | It seems simpler to store all custom (command line set) option values in a struct identical to the predefined ones. It doesn't require: 1) Having so many global variables 2) Copying data from the predefined boards Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mktplinkfw2: update firmware headerRafał Miłecki2017-07-081-26/+26
| | | | | | | 1) Be consistent and use tabs 2) Drop FIXME from boot comments - some images use these fields normally Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mktplinkfw: add option for endianness swapPiotr Dymacz2017-07-041-1/+13
| | | | | | | | This adds command line option in "mktplinkfw" tool for endianness swap in kernel load address and entry point fields. As in "mktplinkfw2" tool, we will need this for little-endian targets, like "ramips". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: mktplinkfw2: add missing options descriptionsPiotr Dymacz2017-07-041-0/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR902AC v1Piotr Dymacz2017-07-041-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: mktplinkfw2: fix MD5 saltRafał Miłecki2017-07-031-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LEDE supports few devices using TP-Link firmware format (V2 or V3): ArcherC20i, ArcherC50, ArcherMR200, TDW8970, TDW8980, TL-WR840N v4, TL-WR841N v13 and VR200v Testing mktplinkfw2 tool with official (vendor generated) firmware files for above devices has shown an error when comparing calculated and included MD5 sum, e.g.: > mktplinkfw2 -i Archer_C20iv1_0.9.1_3.2_up_boot\(170221\)_2017-02-21_17.14.03.bin | grep -A 1 MD5Sum1 Header MD5Sum1 : 22 5a cb 92 10 d2 95 7b df 62 9a f8 62 17 37 10 (*ERROR*) --> expected : ad 19 11 d1 78 98 a7 42 5f 2e 64 da 8a 34 ec cb This problem has been verified to occur with: Archer_C20iv1_0.9.1_3.2_up_boot(170221)_2017-02-21_17.14.03.bin Archer MR200v1_0.9.1_1.1_up_boot_v004a.0 Build 160905 Rel.60037n.bin TD-W8970v3_0.9.1_2.0_up_boot(160816)_2016-08-16_10.40.57.bin TD-W8980v1_0.6.0_1.8_up_boot(150514)_2015-05-14_11.16.43.bin Archer_VR200vv2_0.2.0_0.8.0_up_boot(161202)_2016-12-05_14.39.06.bin For some images, e.g.: Archer_C50v3_EU_0.9.1_0.3_up_boot[170417-rel52298].bin TL-WR840Nv4_EU_0.9.1_4.16_up_boot[170421-rel70692].bin TL-WR841Nv13_0.9.1_3.16_up_boot(161012).bin mktplinkfw2 calculates zero MD5 so these has to be fixed separately: > mktplinkfw2 -i TL-WR841Nv13_0.9.1_3.16_up_boot\(161012\).bin | grep -A 1 MD5Sum1 Header MD5Sum1 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 (*ERROR*) --> expected : 6f 1d 9b 57 5d 42 14 6d bf a2 03 9d 46 7d 55 55 It's most likely that MD5 salt used in mktplinkfw2 has been always wrong (and it's not a matter of e.g. a vendor change). Update it to fix MD5 calculation. This has been also verified to calculate MD5 correctly for other (not yet supported) devices, e.g.: Archer_C3150v2_0.1.0_0.9.1_up_boot(160812)_2016-08-12_10.52.54.bin Archer_C3200v1_0.9.1_0.1_up_boot(160704)_2016-07-04_15.48.28.bin Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: mktplinkfw2: fix support for -w optionRafał Miłecki2017-07-021-1/+1
| | | | | | | This fixes copy & paste typo when reading -w argument. Fixes: 4b35e174caa5b ("firmware-utils: mktplinkfw2: support additional hardware version") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13Piotr Dymacz2017-06-291-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with 5-port FE switch and non-detachable antennas. Both are very similar and are based on MediaTek MT7628NN (aka MT7628N) WiSoC. The difference between these two models is in number of available LEDs, buttons and power input switch. This work is partially based on GitHub PR#974. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - TL-WR840N v4: 5x LED (GPIO-controlled), 1x button - TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Factory image notes: These devices use version 3 of TP-Link header, fortunately without RSA signature (at least in case of devices sold in Europe). The difference lays in the requirement for a non-zero value in "Additional Hardware Version" field. Ideally, it should match the value stored in vendor firmware header on device ("0x4"/"0x13" for these devices) but it seems that anything other than "0" is correct. We are able to prepare factory firwmare file which is accepted and (almost) correctly flashed from the vendor GUI. As it turned out, it accepts files without U-Boot image with second header at the beginning but due to some kind of bug in upgrade routine, flashed image gets corrupted before it's written to flash. Tests showed that the GUI upgrade routine copies value of "Additional Hardware Version" from existing firmware into offset "0x2023c" in provided file, _before_ storing it in flash. In case of vendor firmware upgrade files (which all include U-Boot image and two headers), this offset points to the matching field in kernel+rootfs firmware part header. Unfortunately, in case of LEDE factory image file which contains only one header, it points to the offset "0x2023c" in kernel image. This leads to a corrupted kernel and ends up with a "soft-bricked" device. The good news is that U-Boot in these devices contains well known tftp recovery mode, which can be triggered with "reset" button. What's more, in comparison to some of older MediaTek based TP-Link devices, this recovery mode doesn't write whole file at offset "0x0" in flash, without verifying provided file in advance. In case of recovery mode in these devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes from rest of the file are stored in flash at offset "0x20000". Flash instruction: Until (if at all) TP-Link fixes described problem, the only way to flash LEDE image in these devices is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. To access U-Boot CLI, keep pressed "4" key during boot. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: mktplinkfw2: support additional hardware versionPiotr Dymacz2017-06-291-6/+20
| | | | | | | | | | | | | | | | | | As it turned out, some of new MediaTek based TP-Link devices use value from field at 0x3c offset in version 3 of TP-Link header to specify "Additional Hardware Version". Value from this field is validated during regular (GUI) firmware upgrade on devices like TL-WR840N v4 or TL-WR841N v13. If it's zero (based on some tests, it seems that firmware will accept anything != 0), errors like below are printed on console and upgrade fails: [ rsl_sys_updateFirmware ] 2137: Firmware Additional HardwareVersion check failed [ rdp_updateFirmware ] 345: perror:4506 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C58 v1Henryk Heisig2017-06-291-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 3x button - UART header on PCB, RX, TX at TP4+5 (backside) QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to patch macaddress. Flash instruction: Use "factory" image directly in vendor GUI. Recovery method: 1. Set PC to fixed ip address 192.168.0.66/24. 2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and rename it to "tp_recovery.bin". 3. Start a tftp server with the file "tp_recovery.bin" in its root directory. 4. Turn off the router. 5. Press and hold Reset button. 6. Turn on router with the reset button pressed and wait ~15 seconds. 7. Release the reset button and after a short time the firmware should be transferred from the tftp server. 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f020000 +$filesize cp.b $fileaddr 0x9f020000 $filesize reset This commit is based on GitHub PR#1112 Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* firmware-utils: tplink-safeloader: add support for Archer C5 v2 JP/USJean-Pierre St-Yves2017-06-291-3/+3
| | | | | | Add support for Japan and US versions of TP-Link Archer C5 v2 Signed-off-by: Jean-Pierre St-Yves <jpstyves@gmail.com>
* firmware-utils: tplink-safeloader: add support for Archer C59/C60 RUHenryk Heisig2017-06-291-0/+3
| | | | | | Add support for Russian version of TP-Link Archer C59/C60 v1 Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for TP-Link TL-WA855RE v1Federico Cappon2017-06-291-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/397/198 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x external antennas - 2x LED (green and orange in the same package), 2x button - UART: TP5(TX) and TP4(RX) test points on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in EU version of the device, but should work also with the same device version sold in other countries. Signed-off-by: Federico Cappon <dududede371@gmail.com>
* firmware-utils: fix dgn3500sum compiler warningsMathias Kresin2017-06-261-3/+2
| | | | | | | | | | | The sum variable need to be initialised, otherwise it will points to random stack memory and a bogus image checksum might be calculated. While at it, fix the segfault in case the product region code isn't specified and enable compiler warnings which had revealed all the code issues. Signed-off-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: honor env SOURCE_DATE_EPOCHAlexander Couzens2017-06-199-12/+86
| | | | | | | | Use the timestamp from the enviroment SOURCE_DATE_EPOCH if set instead of the build time. Fixes reproducible builds for certain firmware images. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* firmware-utils: tplink-safeloader: add TP-Link Archer C25 v1Ludwig Thomeczek2017-06-111-1/+58
| | | | | | | | | This adds the necessary firmware layout definitions for the Archer C25. It has an addtional partition containing some static data ("extra-para") without which no factory flash is possible, therefore put_data() has been added. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: add support for TP-Link TL-WR942N v1Serg Studzinskii2017-06-111-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: tplink-safeloader: support strings as soft_versionJan Niehusmann2017-06-111-1/+36
| | | | | | | | | | | | | | | | | | | | | Some TP-Link routers (C25, C59, C60) contain a version string instead of a binary structure in the soft_version partition. Flashing LEDE from the original firmware's GUI, this version string taken from the soft_ver partition of the firmware image is written to the router's config partition. When using tftp recovery to go back to the original Archer C25 firmware, a version check compares that version to the version of the firmware to be flashed. Without proper contents in the config partition, reverting to the original firmware fails. Therefore, write the string "soft_ver:1.0.0\n" to that soft_ver partition. Signed-off-by: Jan Niehusmann <jan@gondor.com>
* firmware-utils: tplink-safeloader: add support for Archer C5 V2Rafał Miłecki2017-03-111-0/+34
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: add support for TP-Link TL-WA850RE v2Piotr Dymacz2017-02-141-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in US version of the device, but should work also with the same device version sold in other countries. Available FLASH space, with LEDE trunk, is only 240 KB. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: improve tools for Buffalo DHP seriesFUKAUMI Naoki2017-01-315-9/+181
| | | | | | | | | some of Buffalo DHP series use slightly different trx magic, buffalo-enc, buffalo-tag, and factory image begin with 'bgn'. this patch adds support for building those images. Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
* ar71xx: add support to TP-Link Archer C59v1 and C60v1Henryk Heisig2017-01-261-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* Revert "tools: wrt400n: fix making factory images with kernel bigger than 1MB"John Crispin2017-01-201-197/+266
| | | | | | | | This reverts commit 5f9b20bc7d0bde6c100a3dec5f02b56f7ef7a61d. The builders were failing with a segfault when generating the image Signed-off-by: John Crispin <john@phrozen.org>
* tools: wrt400n: fix making factory images with kernel bigger than 1MBYousong Zhou2017-01-201-266/+197
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* firmware-utils: tplink-safeloader: add support for TP-Link WBS210/510 1.2Matthias Schiffer2017-01-051-0/+62
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: Add support to TP-Link Archer MR200Henryk Heisig2016-12-221-0/+13
| | | | | | | | | | CPU: MT7620N 580MHz Flash: 8MB RAM: 64MB build-in modem 3G/4G four ethernet port 10/100Mbps Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* firmware-utils/tplink-safeloader: add support for TP-Link RE450Radek Dostál2016-12-221-0/+42
| | | | | | Signed-off-by: Radek Dostál <rd@radekdostal.com> [Jo-Philipp Wich: use .support_trail member] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firmware-utils: kernel image generator for TP-Link RE450Tal Keren2016-12-221-0/+352
| | | | | | | | | | | | | | | | | The firmware image that is used in TP-Link RE450 (and some more devices from the RE series) is tplink-safeloader. In the kernel partition, the kernel is compressed in a regular tp-link firmware that is just used for booting. Since it is only used for compressing and booting, only four fields are filled in the header: Vendor, version, kernel load address and kernel entry point. mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such images. It also specifies the hardware id (as it is in the product info section), so when doing a sysupgrade - the existing code will check for hardware compatibility. Signed-off-by: Tal Keren <kooolk@gmail.com> [rd@radekdostal.com: add build target to .../image/tp-link.mk] Signed-off-by: Radek Dostál <rd@radekdostal.com>
* firmware-utils: add support for TL-WR1043ND v4 to mktplinkfw and ↵Matthias Schiffer2016-12-202-0/+50
| | | | | | | | | tplink-safeloader The TL-WR1043ND v4 uses a kernel image with a mktplinkfw header inside the os-image partition of a tplink-safeloader image. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* firmware-utils/tplink-safeloader: refactor code for further board supportJo-Philipp Wich2016-12-201-301/+265
| | | | | | | | | In order to make it easier to add new boards in the future, refactor the code to describe the image layouts of supported boards in a struct array and alter the image generation routines to figure out the sysupgrade partitions automatically. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.1 at 2024-11-25 21:48:18 +0000