From ddd809f9e56e3a30d459d6189a1582808d204821 Mon Sep 17 00:00:00 2001
From: Felix Fietkau <nbd@openwrt.org>
Date: Sun, 15 Jun 2008 11:11:28 +0000
Subject: (6/6) bcm57xx: package
This is the bcm57xx package. I have tested default vlan functions,
but I dont have the equipment to test more advanced setups. The default
vlan setup seems to be working fine. I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.
I'm not sure which method is best for autoload. For the wrt350n, I
need the activate_gpio parameter. But its probably not a good idea
to add that to the autoload file. On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on? I tried using 'request_module' from
there, but had no success. For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
SVN-Revision: 11471
---
package/broadcom-57xx/src/proto/bcmevent.h | 166 +++++++++++++++++++++++++++++
1 file changed, 166 insertions(+)
create mode 100644 package/broadcom-57xx/src/proto/bcmevent.h
(limited to 'package/broadcom-57xx/src/proto/bcmevent.h')
diff --git a/package/broadcom-57xx/src/proto/bcmevent.h b/package/broadcom-57xx/src/proto/bcmevent.h
new file mode 100644
index 0000000..e862763
--- /dev/null
+++ b/package/broadcom-57xx/src/proto/bcmevent.h
@@ -0,0 +1,166 @@
+/*
+ * Broadcom Event protocol definitions
+ *
+ * Copyright 2007, Broadcom Corporation
+ * All Rights Reserved.
+ *
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+ *
+ *
+ * Dependencies: proto/bcmeth.h
+ *
+ * $Id: bcmevent.h,v 1.1.1.11 2007/05/31 08:00:41 michael Exp $
+ *
+ */
+
+/*
+ * Broadcom Ethernet Events protocol defines
+ *
+ */
+
+#ifndef _BCMEVENT_H_
+#define _BCMEVENT_H_
+
+/* enable structure packing */
+#if defined(__GNUC__)
+#define PACKED __attribute__((packed))
+#else
+#pragma pack(1)
+#define PACKED
+#endif /* defined(__GNUC__) */
+
+#define BCM_EVENT_MSG_VERSION 1 /* wl_event_msg_t struct version */
+#define BCM_MSG_IFNAME_MAX 16 /* max length of interface name */
+
+/* flags */
+#define WLC_EVENT_MSG_LINK 0x01 /* link is up */
+#define WLC_EVENT_MSG_FLUSHTXQ 0x02 /* flush tx queue on MIC error */
+#define WLC_EVENT_MSG_GROUP 0x04 /* group MIC error */
+
+/* these fields are stored in network order */
+typedef struct
+{
+ uint16 version;
+ uint16 flags; /* see flags below */
+ uint32 event_type; /* Message (see below) */
+ uint32 status; /* Status code (see below) */
+ uint32 reason; /* Reason code (if applicable) */
+ uint32 auth_type; /* WLC_E_AUTH */
+ uint32 datalen; /* data buf */
+ struct ether_addr addr; /* Station address (if applicable) */
+ char ifname[BCM_MSG_IFNAME_MAX]; /* name of the packet incoming interface */
+} PACKED wl_event_msg_t;
+
+/* used by driver msgs */
+typedef struct bcm_event {
+ struct ether_header eth;
+ bcmeth_hdr_t bcm_hdr;
+ wl_event_msg_t event;
+ /* data portion follows */
+} PACKED bcm_event_t;
+
+#define BCM_MSG_LEN (sizeof(bcm_event_t) - sizeof(bcmeth_hdr_t) - sizeof(struct ether_header))
+
+/* Event messages */
+#define WLC_E_SET_SSID 0 /* indicates status of set SSID */
+#define WLC_E_JOIN 1 /* differentiates join IBSS from found (WLC_E_START) IBSS */
+#define WLC_E_START 2 /* STA founded an IBSS or AP started a BSS */
+#define WLC_E_AUTH 3 /* 802.11 AUTH request */
+#define WLC_E_AUTH_IND 4 /* 802.11 AUTH indication */
+#define WLC_E_DEAUTH 5 /* 802.11 DEAUTH request */
+#define WLC_E_DEAUTH_IND 6 /* 802.11 DEAUTH indication */
+#define WLC_E_ASSOC 7 /* 802.11 ASSOC request */
+#define WLC_E_ASSOC_IND 8 /* 802.11 ASSOC indication */
+#define WLC_E_REASSOC 9 /* 802.11 REASSOC request */
+#define WLC_E_REASSOC_IND 10 /* 802.11 REASSOC indication */
+#define WLC_E_DISASSOC 11 /* 802.11 DISASSOC request */
+#define WLC_E_DISASSOC_IND 12 /* 802.11 DISASSOC indication */
+#define WLC_E_QUIET_START 13 /* 802.11h Quiet period started */
+#define WLC_E_QUIET_END 14 /* 802.11h Quiet period ended */
+#define WLC_E_BEACON_RX 15 /* BEACONS received/lost indication */
+#define WLC_E_LINK 16 /* generic link indication */
+#define WLC_E_MIC_ERROR 17 /* TKIP MIC error occurred */
+#define WLC_E_NDIS_LINK 18 /* NDIS style link indication */
+#define WLC_E_ROAM 19 /* roam attempt occurred: indicate status & reason */
+#define WLC_E_TXFAIL 20 /* change in dot11FailedCount (txfail) */
+#define WLC_E_PMKID_CACHE 21 /* WPA2 pmkid cache indication */
+#define WLC_E_RETROGRADE_TSF 22 /* current AP's TSF value went backward */
+#define WLC_E_PRUNE 23 /* AP was pruned from join list for reason */
+#define WLC_E_AUTOAUTH 24 /* report AutoAuth table entry match for join attempt */
+#define WLC_E_EAPOL_MSG 25 /* Event encapsulating an EAPOL message */
+#define WLC_E_SCAN_COMPLETE 26 /* Scan results are ready or scan was aborted */
+#define WLC_E_ADDTS_IND 27 /* indicate to host addts fail/success */
+#define WLC_E_DELTS_IND 28 /* indicate to host delts fail/success */
+#define WLC_E_BCNSENT_IND 29 /* indicate to host of beacon transmit */
+#define WLC_E_BCNRX_MSG 30 /* Send the received beacon up to the host */
+#define WLC_E_BCNLOST_MSG 31 /* indicate to host loss of beacon */
+#define WLC_E_ROAM_PREP 32 /* before attempting to roam */
+#define WLC_E_PFN_NET_FOUND 33 /* PFN network found event */
+#define WLC_E_PFN_NET_LOST 34 /* PFN network lost event */
+
+#ifdef EXT_STA
+#define WLC_E_RESET_COMPLETE 35
+#define WLC_E_JOIN_START 36
+#define WLC_E_ROAM_START 37
+#define WLC_E_ASSOC_START 38
+#define WLC_E_IBSS_ASSOC 39
+#define WLC_E_RADIO 40
+#define WLC_E_LAST 41 /* highest val + 1 for range checking */
+#else /* EXT_STA */
+#define WLC_E_LAST 35 /* highest val + 1 for range checking */
+#endif /* EXT_STA */
+
+/* Event status codes */
+#define WLC_E_STATUS_SUCCESS 0 /* operation was successful */
+#define WLC_E_STATUS_FAIL 1 /* operation failed */
+#define WLC_E_STATUS_TIMEOUT 2 /* operation timed out */
+#define WLC_E_STATUS_NO_NETWORKS 3 /* failed due to no matching network found */
+#define WLC_E_STATUS_ABORT 4 /* operation was aborted */
+#define WLC_E_STATUS_NO_ACK 5 /* protocol failure: packet not ack'd */
+#define WLC_E_STATUS_UNSOLICITED 6 /* AUTH or ASSOC packet was unsolicited */
+#define WLC_E_STATUS_ATTEMPT 7 /* attempt to assoc to an auto auth configuration */
+#define WLC_E_STATUS_PARTIAL 8 /* scan results are incomplete */
+#define WLC_E_STATUS_NEWSCAN 9 /* scan aborted by another scan */
+#define WLC_E_STATUS_NEWASSOC 10 /* scan aborted due to assoc in progress */
+#define WLC_E_STATUS_11HQUIET 11 /* 802.11h quiet period started */
+#define WLC_E_STATUS_SUPPRESS 12 /* user disabled scanning (WLC_SET_SCANSUPPRESS) */
+#define WLC_E_STATUS_NOCHANS 13 /* no allowable channels to scan */
+#define WLC_E_STATUS_CCXFASTRM 14 /* scan aborted due to CCX fast roam */
+
+/* roam reason codes */
+#define WLC_E_REASON_INITIAL_ASSOC 0 /* initial assoc */
+#define WLC_E_REASON_LOW_RSSI 1 /* roamed due to low RSSI */
+#define WLC_E_REASON_DEAUTH 2 /* roamed due to DEAUTH indication */
+#define WLC_E_REASON_DISASSOC 3 /* roamed due to DISASSOC indication */
+#define WLC_E_REASON_BCNS_LOST 4 /* roamed due to lost beacons */
+#define WLC_E_REASON_FAST_ROAM_FAILED 5 /* roamed due to fast roam failure */
+#define WLC_E_REASON_DIRECTED_ROAM 6 /* roamed due to request by AP */
+#define WLC_E_REASON_TSPEC_REJECTED 7 /* roamed due to TSPEC rejection */
+#define WLC_E_REASON_BETTER_AP 8 /* roamed due to finding better AP */
+
+/* prune reason codes */
+#define WLC_E_PRUNE_ENCR_MISMATCH 1 /* encryption mismatch */
+#define WLC_E_PRUNE_BCAST_BSSID 2 /* AP uses a broadcast BSSID */
+#define WLC_E_PRUNE_MAC_DENY 3 /* STA's MAC addr is in AP's MAC deny list */
+#define WLC_E_PRUNE_MAC_NA 4 /* STA's MAC addr is not in AP's MAC allow list */
+#define WLC_E_PRUNE_REG_PASSV 5 /* AP not allowed due to regulatory restriction */
+#define WLC_E_PRUNE_SPCT_MGMT 6 /* AP does not support STA locale spectrum mgmt */
+#define WLC_E_PRUNE_RADAR 7 /* AP is on a radar channel of STA locale */
+#define WLC_E_RSN_MISMATCH 8 /* STA does not support AP's RSN */
+#define WLC_E_PRUNE_NO_COMMON_RATES 9 /* No rates in common with AP */
+#define WLC_E_PRUNE_BASIC_RATES 10 /* STA does not support all basic rates of BSS */
+#define WLC_E_PRUNE_CIPHER_NA 12 /* BSS's cipher not supported */
+#define WLC_E_PRUNE_KNOWN_STA 13 /* AP is already known to us as a STA */
+#define WLC_E_PRUNE_WDS_PEER 15 /* AP is already known to us as a WDS peer */
+#define WLC_E_PRUNE_QBSS_LOAD 16 /* QBSS LOAD - AAC is too low */
+#define WLC_E_PRUNE_HOME_AP 17 /* prune home AP */
+
+#undef PACKED
+#if !defined(__GNUC__)
+#pragma pack()
+#endif /* PACKED */
+
+#endif /* _BCMEVENT_H_ */
--
cgit v1.1