From 88ddb3746188037afd38d631f7a893587fa8bdf0 Mon Sep 17 00:00:00 2001 From: John Crispin Date: Wed, 11 Feb 2015 10:09:23 +0000 Subject: ipq806x: update target to v3.18 Patches in the ipq806x/patches folder were out of tree in v3.14. The newest patch at the time was from June, so we can safely assume that either the patches have been merged, or they have been rejected for a good reason. If patches are seen missing, we'll cherry-pick them on a per-needed basis. This new kernel have been tested on AP148, which seems to works fine. Signed-off-by: Mathieu Olivari SVN-Revision: 44386 --- ...maengine-qcom_adm-Add-device-tree-binding.patch | 76 ---------------------- 1 file changed, 76 deletions(-) delete mode 100644 target/linux/ipq806x/patches/0178-dmaengine-qcom_adm-Add-device-tree-binding.patch (limited to 'target/linux/ipq806x/patches/0178-dmaengine-qcom_adm-Add-device-tree-binding.patch') diff --git a/target/linux/ipq806x/patches/0178-dmaengine-qcom_adm-Add-device-tree-binding.patch b/target/linux/ipq806x/patches/0178-dmaengine-qcom_adm-Add-device-tree-binding.patch deleted file mode 100644 index 1c72a2f..0000000 --- a/target/linux/ipq806x/patches/0178-dmaengine-qcom_adm-Add-device-tree-binding.patch +++ /dev/null @@ -1,76 +0,0 @@ -From 331294fa5c703536e27b79e9c112d162393f725a Mon Sep 17 00:00:00 2001 -From: Andy Gross -Date: Thu, 26 Jun 2014 13:55:10 -0500 -Subject: [PATCH 178/182] dmaengine: qcom_adm: Add device tree binding - -Add device tree binding support for the QCOM ADM DMA driver. - -Signed-off-by: Andy Gross ---- - Documentation/devicetree/bindings/dma/qcom_adm.txt | 60 ++++++++++++++++++++ - 1 file changed, 60 insertions(+) - create mode 100644 Documentation/devicetree/bindings/dma/qcom_adm.txt - ---- /dev/null -+++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt -@@ -0,0 +1,60 @@ -+QCOM ADM DMA Controller -+ -+Required properties: -+- compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960 -+- reg: Address range for DMA registers -+- interrupts: Should contain one interrupt shared by all channels -+- #dma-cells: must be <2>. First cell denotes the channel number. Second cell -+ denotes CRCI (client rate control interface) flow control assignment. -+- clocks: Should contain the core clock and interface clock. -+- clock-names: Must contain "core" for the core clock and "iface" for the -+ interface clock. -+- resets: Must contain an entry for each entry in reset names. -+- reset-names: Must include the following entries: -+ - clk -+ - c0 -+ - c1 -+ - c2 -+- qcom,ee: indicates the security domain identifier used in the secure world. -+ -+Example: -+ adm_dma: dma@18300000 { -+ compatible = "qcom,adm"; -+ reg = <0x18300000 0x100000>; -+ interrupts = <0 170 0>; -+ #dma-cells = <2>; -+ -+ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; -+ clock-names = "core", "iface"; -+ -+ resets = <&gcc ADM0_RESET>, -+ <&gcc ADM0_C0_RESET>, -+ <&gcc ADM0_C1_RESET>, -+ <&gcc ADM0_C2_RESET>; -+ reset-names = "clk", "c0", "c1", "c2"; -+ qcom,ee = <0>; -+ }; -+ -+DMA clients must use the format descripted in the dma.txt file, using a three -+cell specifier for each channel. -+ -+Each dmas request consists of 3 cells: -+ 1. phandle pointing to the DMA controller -+ 2. channel number -+ 3. CRCI assignment, if applicable. If no CRCI flow control is required, use 0. -+ -+Example: -+ -+ spi4: spi@1a280000 { -+ status = "ok"; -+ spi-max-frequency = <50000000>; -+ -+ pinctrl-0 = <&spi_pins>; -+ pinctrl-names = "default"; -+ -+ cs-gpios = <&qcom_pinmux 20 0>; -+ -+ dmas = <&adm_dma 6 9>, -+ <&adm_dma 5 10>; -+ dma-names = "rx", "tx"; -+ }; -- cgit v1.1