From 14951e8f8e09ba6e2cff140769189a66155a5345 Mon Sep 17 00:00:00 2001 From: Henryk Heisig Date: Sun, 28 Jan 2018 19:49:38 +0100 Subject: ramips: add support for TP-Link Archer C50 v3 TP-Link Archer C50 v3 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7612E. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Flash instruction: The only way to flash LEDE image in ArcherC50v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Henryk Heisig --- target/linux/ramips/base-files/etc/board.d/01_leds | 6 ++++++ target/linux/ramips/base-files/etc/board.d/02_network | 1 + target/linux/ramips/base-files/etc/diag.sh | 1 + target/linux/ramips/base-files/lib/upgrade/platform.sh | 1 + 4 files changed, 9 insertions(+) (limited to 'target/linux/ramips/base-files') diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 110b588..677bf95 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -393,6 +393,12 @@ tplink,c20-v4) ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:green:wlan2g" "wlan0" ;; +tplink,c50-v3) + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1e" + ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" + ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:green:wlan2g" "wlan1" + set_wifi_led "$boardname:green:wlan5g" + ;; tplink,tl-mr3420-v5) set_usb_led "$boardname:green:usb" set_wifi_led "$boardname:green:wlan" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index d385594..d064bfe 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -175,6 +175,7 @@ ramips_setup_interfaces() rb750gr3|\ rt-n14u|\ tplink,c20-v4|\ + tplink,c50-v3|\ tplink,tl-mr3420-v5|\ tl-wr840n-v4|\ tl-wr840n-v5|\ diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index 068df1d..6b11fb2 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -39,6 +39,7 @@ get_status_led() { pwh2004|\ r6220|\ tplink,c20-v4|\ + tplink,c50-v3|\ tplink,tl-mr3420-v5|\ tl-wr840n-v4|\ tl-wr840n-v5|\ diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 892dfe3..45e141d 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -244,6 +244,7 @@ platform_check_image() { mr200|\ tplink,c20-v1|\ tplink,c20-v4|\ + tplink,c50-v3|\ tplink,tl-mr3420-v5|\ tl-wr840n-v4|\ tl-wr840n-v5|\ -- cgit v1.1