From 7b1e525b56743a96c52cb25a6a12cbe7f5d58995 Mon Sep 17 00:00:00 2001 From: Gabor Juhos Date: Fri, 23 Dec 2011 14:27:16 +0000 Subject: ramips: initial support for Sitecom WL-351 v1 002 This add support for the Sitecom WL-351 v1 002. In principle the Engenius ESR9850 should also work with this, but I don't have the hardware to test it. Since an external gigabit switch (RTL8366RB) is used, I had to modify the ramips_esw driver to add a 'bypass' mode, which just configures it to not filter the vlan tags. Also two initialization words (FCT2 and FPA2) are set to different values by u-boot than what the driver is using and it only seems to work correctly when they not overridden by the driver, so I added them to the platform specific data as reg_initval_fct2 and reg_initval_fpa2. With this wired lan works as expected, however I'm still having some trouble with the wireless lan: It only works after I rmmod & re-insmod rt2800pci and then reconfigure it in the webinterface, but not directly after rebooting. The symptom of this is wpad saying: Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA IEEE 802.11: associated (aid 1) Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA WPA: pairwise key handshake completed (RSN) Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA IEEE 802.11: authenticated But wpa_supplicant on the client saying: Authentication with timed out. Signed-off-by: Tobias Diedrich SVN-Revision: 29604 --- target/linux/ramips/base-files/etc/diag.sh | 3 +++ .../ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom | 1 + target/linux/ramips/base-files/etc/uci-defaults/network | 10 +++++++++- target/linux/ramips/base-files/lib/ramips.sh | 3 +++ 4 files changed, 16 insertions(+), 1 deletion(-) (limited to 'target/linux/ramips/base-files') diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index a150cc2..edb8376 100755 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -66,6 +66,9 @@ get_status_led() { whr-g300n) status_led="whr-g300n:green:router" ;; + wl-351) + status_led="wl-351:amber:power" + ;; esac } diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom index fa6607f..a1d4887 100644 --- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom +++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom @@ -59,6 +59,7 @@ case "$FIRMWARE" in v22rw-2x2 | \ wcr-150gn | \ whr-g300n | \ + wl-351 | \ wr512-3gn) rt2x00_eeprom_extract "factory" 0 272 ;; diff --git a/target/linux/ramips/base-files/etc/uci-defaults/network b/target/linux/ramips/base-files/etc/uci-defaults/network index bb1d90e..60dd716 100755 --- a/target/linux/ramips/base-files/etc/uci-defaults/network +++ b/target/linux/ramips/base-files/etc/uci-defaults/network @@ -23,6 +23,13 @@ ramips_setup_interfaces() ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" ;; + wl-351) + ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" + ucidef_add_switch "rtl8366rb" "1" "1" + ucidef_add_switch_vlan "rtl8366rb" "1" "0 1 2 3 5t" + ucidef_add_switch_vlan "rtl8366rb" "2" "4 5t" + ;; + rt-n15) ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" ucidef_add_switch "rtl8366s" "1" "1" @@ -56,7 +63,8 @@ ramips_setup_macs() argus-atp52b | \ b2c | \ nw718 | \ - rt-n15) + rt-n15 | \ + wl-351) lan_mac=$(ramips_get_mac_binary factory 4) wan_mac=$(/usr/sbin/maccalc add "$lan_mac" 1) ;; diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index faed421..4dc10ae 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -104,6 +104,9 @@ ramips_board_name() { *"WHR-G300N") name="whr-g300n" ;; + *"Sitecom WL-351 v1 002") + name="wl-351" + ;; *"WZR-AGL300NH") name="wzr-agl300nh" ;; -- cgit v1.1