--- /dev/null
+++ b/arch/arm/configs/bcmrpi_cutdown_defconfig
@@ -0,0 +1,504 @@
+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+# CONFIG_UID16 is not set
+# CONFIG_KALLSYMS is not set
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_BCM2708=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_AEABI=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext3 rootwait"
+CONFIG_CPU_IDLE=y
+CONFIG_VFP=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_NET_PKTGEN=m
+CONFIG_IRDA=m
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+CONFIG_IRDA_ULTRA=y
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+CONFIG_IRDA_FAST_RR=y
+CONFIG_IRTTY_SIR=m
+CONFIG_KINGSUN_DONGLE=m
+CONFIG_KSDAZZLE_DONGLE=m
+CONFIG_KS959_DONGLE=m
+CONFIG_USB_IRDA=m
+CONFIG_SIGMATEL_FIR=m
+CONFIG_MCS_FIR=m
+CONFIG_BT=m
+CONFIG_BT_L2CAP=y
+CONFIG_BT_SCO=y
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
+CONFIG_BT_ATH3K=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_RC_PID=y
+CONFIG_MAC80211_MESH=y
+CONFIG_WIMAX=m
+CONFIG_NET_9P=m
+CONFIG_NFC=m
+CONFIG_NFC_PN533=m
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_MISC_DEVICES=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_TUN=m
+CONFIG_PHYLIB=m
+CONFIG_MDIO_BITBANG=m
+CONFIG_NET_ETHERNET=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_LIBERTAS_THINFIRM_USB=m
+CONFIG_AT76C50X_USB=m
+CONFIG_USB_ZD1201=m
+CONFIG_USB_NET_RNDIS_WLAN=m
+CONFIG_RTL8187=m
+CONFIG_MAC80211_HWSIM=m
+CONFIG_ATH_COMMON=m
+CONFIG_ATH9K=m
+CONFIG_ATH9K_HTC=m
+CONFIG_CARL9170=m
+CONFIG_B43=m
+CONFIG_B43LEGACY=m
+CONFIG_HOSTAP=m
+CONFIG_IWM=m
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_P54_COMMON=m
+CONFIG_P54_USB=m
+CONFIG_RT2X00=m
+CONFIG_RT2500USB=m
+CONFIG_RT73USB=m
+CONFIG_RT2800USB=m
+CONFIG_RT2800USB_RT53XX=y
+CONFIG_RTL8192CU=m
+CONFIG_WL1251=m
+CONFIG_WL12XX_MENU=m
+CONFIG_ZD1211RW=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_WIMAX_I2400M_USB=m
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=y
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+CONFIG_USB_NET_CDC_EEM=m
+CONFIG_USB_NET_DM9601=m
+CONFIG_USB_NET_SMSC75XX=m
+CONFIG_USB_NET_SMSC95XX=y
+CONFIG_USB_NET_GL620A=m
+CONFIG_USB_NET_NET1080=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_USB_NET_CDC_SUBSET=m
+CONFIG_USB_ALI_M5632=y
+CONFIG_USB_AN2720=y
+CONFIG_USB_KC2190=y
+# CONFIG_USB_NET_ZAURUS is not set
+CONFIG_USB_NET_CX82310_ETH=m
+CONFIG_USB_NET_KALMIA=m
+CONFIG_USB_NET_INT51X1=m
+CONFIG_USB_IPHETH=m
+CONFIG_USB_SIERRA_NET=m
+CONFIG_USB_VL600=m
+CONFIG_PPP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_NETCONSOLE=m
+CONFIG_INPUT_POLLDEV=m
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_JOYDEV=m
+CONFIG_INPUT_EVDEV=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AD714X=m
+CONFIG_INPUT_ATI_REMOTE=m
+CONFIG_INPUT_ATI_REMOTE2=m
+CONFIG_INPUT_KEYSPAN_REMOTE=m
+CONFIG_INPUT_POWERMATE=m
+CONFIG_INPUT_YEALINK=m
+CONFIG_INPUT_CM109=m
+CONFIG_INPUT_UINPUT=m
+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
+CONFIG_INPUT_ADXL34X=m
+CONFIG_INPUT_CMA3000=m
+CONFIG_SERIO=m
+CONFIG_SERIO_RAW=m
+CONFIG_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_RAW_DRIVER=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_BCM2708_WDT=m
+# CONFIG_MFD_SUPPORT is not set
+CONFIG_FB=y
+CONFIG_FB_BCM2708=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_HRTIMER=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_ALOOP=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+CONFIG_SND_BCM2835=m
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_UA101=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_6FIRE=m
+CONFIG_SOUND_PRIME=m
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_ACRUX=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_DRAGONRISE=m
+CONFIG_HID_EMS_FF=m
+CONFIG_HID_ELECOM=m
+CONFIG_HID_EZKEY=m
+CONFIG_HID_HOLTEK=m
+CONFIG_HID_KEYTOUCH=m
+CONFIG_HID_KYE=m
+CONFIG_HID_UCLOGIC=m
+CONFIG_HID_WALTOP=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_TWINHAN=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LCPOWER=m
+CONFIG_HID_LOGITECH=m
+CONFIG_HID_MAGICMOUSE=m
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_MULTITOUCH=m
+CONFIG_HID_NTRIG=m
+CONFIG_HID_ORTEK=m
+CONFIG_HID_PANTHERLORD=m
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_PICOLCD=m
+CONFIG_HID_QUANTA=m
+CONFIG_HID_ROCCAT=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SPEEDLINK=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_GREENASIA=m
+CONFIG_HID_SMARTJOYPLUS=m
+CONFIG_HID_TOPSEED=m
+CONFIG_HID_THRUSTMASTER=m
+CONFIG_HID_WACOM=m
+CONFIG_HID_WIIMOTE=m
+CONFIG_HID_ZEROPLUS=m
+CONFIG_HID_ZYDACRON=m
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_MON=m
+CONFIG_USB_DWCOTG=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_ONETOUCH=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
+CONFIG_USB_STORAGE_ENE_UB6250=m
+CONFIG_USB_UAS=m
+CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_FUNSOFT=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OTI6858=m
+CONFIG_USB_SERIAL_QCAUX=m
+CONFIG_USB_SERIAL_QUALCOMM=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_HP4X=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SIEMENS_MPI=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_SYMBOL=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_VIVOPAY_SERIAL=m
+CONFIG_USB_SERIAL_ZIO=m
+CONFIG_USB_SERIAL_SSU100=m
+CONFIG_USB_SERIAL_DEBUG=m
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+CONFIG_USB_ADUTUX=m
+CONFIG_USB_SEVSEG=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_LED=m
+CONFIG_USB_CYPRESS_CY7C63=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_IDMOUSE=m
+CONFIG_USB_FTDI_ELAN=m
+CONFIG_USB_APPLEDISPLAY=m
+CONFIG_USB_LD=m
+CONFIG_USB_TRANCEVIBRATOR=m
+CONFIG_USB_IOWARRIOR=m
+CONFIG_USB_TEST=m
+CONFIG_USB_ISIGHTFW=m
+CONFIG_USB_YUREX=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM2708=y
+CONFIG_MMC_SDHCI_BCM2708_DMA=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+CONFIG_UIO=m
+CONFIG_UIO_PDRV=m
+CONFIG_UIO_PDRV_GENIRQ=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_XFS_RT=y
+CONFIG_GFS2_FS=m
+CONFIG_OCFS2_FS=m
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
+CONFIG_NILFS2_FS=m
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
+CONFIG_FSCACHE=y
+CONFIG_CACHEFILES=y
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+CONFIG_NTFS_FS=m
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFS_FSCACHE=y
+CONFIG_CIFS=m
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_9P_FS=m
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+# CONFIG_ARM_UNWIND is not set
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_SEQIV=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEFLATE=m
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_LIBCRC32C=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_BCM2708=m
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_BCM2708=m
+
--- /dev/null
+++ b/arch/arm/configs/bcmrpi_defconfig
@@ -0,0 +1,743 @@
+# CONFIG_ARM_PATCH_PHYS_VIRT is not set
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_RESOURCE_COUNTERS=y
+CONFIG_BLK_CGROUP=y
+CONFIG_NAMESPACES=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_OPROFILE=m
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_BLK_DEV_THROTTLING=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
+CONFIG_CFQ_GROUP_IOSCHED=y
+CONFIG_ARCH_BCM2708=y
+CONFIG_AEABI=y
+CONFIG_SECCOMP=y
+CONFIG_CC_STACKPROTECTOR=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext3 rootwait"
+CONFIG_KEXEC=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_STAT=m
+CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_IDLE=y
+CONFIG_VFP=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET_XFRM_MODE_TRANSPORT=m
+CONFIG_INET_XFRM_MODE_TUNNEL=m
+CONFIG_INET_XFRM_MODE_BEET=m
+CONFIG_INET_LRO=m
+CONFIG_INET_DIAG=m
+CONFIG_IPV6_PRIVACY=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CONNTRACK_TIMESTAMP=y
+CONFIG_NF_CT_PROTO_DCCP=m
+CONFIG_NF_CT_PROTO_SCTP=m
+CONFIG_NF_CT_PROTO_UDPLITE=m
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_TPROXY=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_AUDIT=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_CPU=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
+CONFIG_NF_CONNTRACK_IPV4=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_NF_CONNTRACK_IPV6=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_IP6=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_BRIDGE_EBT_ULOG=m
+CONFIG_BRIDGE_EBT_NFLOG=m
+CONFIG_L2TP=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_MULTIQ=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFB=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_DRR=m
+CONFIG_NET_SCH_MQPRIO=m
+CONFIG_NET_SCH_CHOKE=m
+CONFIG_NET_SCH_QFQ=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_CLS_U32_MARK=y
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+CONFIG_NET_CLS_CGROUP=m
+CONFIG_NET_EMATCH=y
+CONFIG_NET_EMATCH_CMP=m
+CONFIG_NET_EMATCH_NBYTE=m
+CONFIG_NET_EMATCH_U32=m
+CONFIG_NET_EMATCH_META=m
+CONFIG_NET_EMATCH_TEXT=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=m
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_IPT=m
+CONFIG_NET_ACT_NAT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_NET_ACT_SIMP=m
+CONFIG_NET_ACT_SKBEDIT=m
+CONFIG_NET_ACT_CSUM=m
+CONFIG_NET_PKTGEN=m
+CONFIG_IRDA=m
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+CONFIG_IRDA_ULTRA=y
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+CONFIG_IRDA_FAST_RR=y
+CONFIG_IRTTY_SIR=m
+CONFIG_KINGSUN_DONGLE=m
+CONFIG_KSDAZZLE_DONGLE=m
+CONFIG_KS959_DONGLE=m
+CONFIG_USB_IRDA=m
+CONFIG_SIGMATEL_FIR=m
+CONFIG_MCS_FIR=m
+CONFIG_BT=m
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
+CONFIG_BT_ATH3K=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_RC_PID=y
+CONFIG_MAC80211_MESH=y
+CONFIG_WIMAX=m
+CONFIG_NET_9P=m
+CONFIG_NFC=m
+CONFIG_NFC_PN533=m
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_MD=y
+CONFIG_NETDEVICES=y
+CONFIG_NETCONSOLE=m
+CONFIG_TUN=m
+CONFIG_MDIO_BITBANG=m
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=y
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+CONFIG_USB_NET_CDC_EEM=m
+CONFIG_USB_NET_DM9601=m
+CONFIG_USB_NET_SMSC75XX=m
+CONFIG_USB_NET_SMSC95XX=y
+CONFIG_USB_NET_GL620A=m
+CONFIG_USB_NET_NET1080=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_USB_NET_CDC_SUBSET=m
+CONFIG_USB_ALI_M5632=y
+CONFIG_USB_AN2720=y
+CONFIG_USB_KC2190=y
+# CONFIG_USB_NET_ZAURUS is not set
+CONFIG_USB_NET_CX82310_ETH=m
+CONFIG_USB_NET_KALMIA=m
+CONFIG_USB_NET_INT51X1=m
+CONFIG_USB_IPHETH=m
+CONFIG_USB_SIERRA_NET=m
+CONFIG_USB_VL600=m
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_LIBERTAS_THINFIRM_USB=m
+CONFIG_AT76C50X_USB=m
+CONFIG_USB_ZD1201=m
+CONFIG_USB_NET_RNDIS_WLAN=m
+CONFIG_RTL8187=m
+CONFIG_MAC80211_HWSIM=m
+CONFIG_B43=m
+CONFIG_B43LEGACY=m
+CONFIG_HOSTAP=m
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_P54_COMMON=m
+CONFIG_P54_USB=m
+CONFIG_RT2X00=m
+CONFIG_RT2500USB=m
+CONFIG_RT73USB=m
+CONFIG_RT2800USB=m
+CONFIG_RT2800USB_RT53XX=y
+CONFIG_RT2800USB_UNKNOWN=y
+CONFIG_ZD1211RW=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_WIMAX_I2400M_USB=m
+CONFIG_INPUT_POLLDEV=m
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_JOYDEV=m
+CONFIG_INPUT_EVDEV=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AD714X=m
+CONFIG_INPUT_ATI_REMOTE2=m
+CONFIG_INPUT_KEYSPAN_REMOTE=m
+CONFIG_INPUT_POWERMATE=m
+CONFIG_INPUT_YEALINK=m
+CONFIG_INPUT_CM109=m
+CONFIG_INPUT_UINPUT=m
+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
+CONFIG_INPUT_ADXL34X=m
+CONFIG_INPUT_CMA3000=m
+CONFIG_SERIO=m
+CONFIG_SERIO_RAW=m
+CONFIG_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_RAW_DRIVER=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_BCM2708=m
+CONFIG_SPI=y
+CONFIG_SPI_BCM2708=m
+CONFIG_SPI_SPIDEV=m
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_THERMAL=y
+CONFIG_THERMAL_BCM2835=y
+CONFIG_WATCHDOG=y
+CONFIG_BCM2708_WDT=m
+CONFIG_MEDIA_SUPPORT=m
+CONFIG_FB=y
+CONFIG_FB_BCM2708=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_HRTIMER=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_ALOOP=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+CONFIG_SND_BCM2835=m
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_UA101=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_6FIRE=m
+CONFIG_SOUND_PRIME=m
+CONFIG_HID_A4TECH=m
+CONFIG_HID_ACRUX=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_DRAGONRISE=m
+CONFIG_HID_EMS_FF=m
+CONFIG_HID_ELECOM=m
+CONFIG_HID_EZKEY=m
+CONFIG_HID_HOLTEK=m
+CONFIG_HID_KEYTOUCH=m
+CONFIG_HID_KYE=m
+CONFIG_HID_UCLOGIC=m
+CONFIG_HID_WALTOP=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_TWINHAN=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LCPOWER=m
+CONFIG_HID_LOGITECH=m
+CONFIG_HID_MAGICMOUSE=m
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_MULTITOUCH=m
+CONFIG_HID_NTRIG=m
+CONFIG_HID_ORTEK=m
+CONFIG_HID_PANTHERLORD=m
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_PICOLCD=m
+CONFIG_HID_ROCCAT=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SPEEDLINK=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_GREENASIA=m
+CONFIG_HID_SMARTJOYPLUS=m
+CONFIG_HID_TOPSEED=m
+CONFIG_HID_THRUSTMASTER=m
+CONFIG_HID_ZEROPLUS=m
+CONFIG_HID_ZYDACRON=m
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_MON=m
+CONFIG_USB_DWCOTG=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_ONETOUCH=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
+CONFIG_USB_STORAGE_ENE_UB6250=m
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_FUNSOFT=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OTI6858=m
+CONFIG_USB_SERIAL_QCAUX=m
+CONFIG_USB_SERIAL_QUALCOMM=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_HP4X=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SIEMENS_MPI=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_SYMBOL=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_VIVOPAY_SERIAL=m
+CONFIG_USB_SERIAL_ZIO=m
+CONFIG_USB_SERIAL_SSU100=m
+CONFIG_USB_SERIAL_DEBUG=m
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+CONFIG_USB_ADUTUX=m
+CONFIG_USB_SEVSEG=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_LED=m
+CONFIG_USB_CYPRESS_CY7C63=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_IDMOUSE=m
+CONFIG_USB_FTDI_ELAN=m
+CONFIG_USB_APPLEDISPLAY=m
+CONFIG_USB_LD=m
+CONFIG_USB_TRANCEVIBRATOR=m
+CONFIG_USB_IOWARRIOR=m
+CONFIG_USB_TEST=m
+CONFIG_USB_ISIGHTFW=m
+CONFIG_USB_YUREX=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM2708=y
+CONFIG_MMC_SDHCI_BCM2708_DMA=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_DS1307=m
+CONFIG_RTC_DRV_DS1374=m
+CONFIG_RTC_DRV_DS1672=m
+CONFIG_RTC_DRV_DS3232=m
+CONFIG_RTC_DRV_MAX6900=m
+CONFIG_RTC_DRV_RS5C372=m
+CONFIG_RTC_DRV_ISL1208=m
+CONFIG_RTC_DRV_ISL12022=m
+CONFIG_RTC_DRV_X1205=m
+CONFIG_RTC_DRV_PCF8563=m
+CONFIG_RTC_DRV_PCF8583=m
+CONFIG_RTC_DRV_M41T80=m
+CONFIG_RTC_DRV_BQ32K=m
+CONFIG_RTC_DRV_S35390A=m
+CONFIG_RTC_DRV_FM3130=m
+CONFIG_RTC_DRV_RX8581=m
+CONFIG_RTC_DRV_RX8025=m
+CONFIG_RTC_DRV_EM3027=m
+CONFIG_RTC_DRV_RV3029C2=m
+CONFIG_RTC_DRV_M41T93=m
+CONFIG_RTC_DRV_M41T94=m
+CONFIG_RTC_DRV_DS1305=m
+CONFIG_RTC_DRV_DS1390=m
+CONFIG_RTC_DRV_MAX6902=m
+CONFIG_RTC_DRV_R9701=m
+CONFIG_RTC_DRV_RS5C348=m
+CONFIG_RTC_DRV_DS3234=m
+CONFIG_RTC_DRV_PCF2123=m
+CONFIG_UIO=m
+CONFIG_UIO_PDRV=m
+CONFIG_UIO_PDRV_GENIRQ=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_JFS_STATISTICS=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_XFS_RT=y
+CONFIG_GFS2_FS=m
+CONFIG_OCFS2_FS=m
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
+CONFIG_NILFS2_FS=m
+CONFIG_FANOTIFY=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
+CONFIG_FSCACHE=y
+CONFIG_FSCACHE_STATS=y
+CONFIG_FSCACHE_HISTOGRAM=y
+CONFIG_CACHEFILES=y
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+CONFIG_NTFS_FS=m
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFS_FSCACHE=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_CIFS=m
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_9P_FS=m
+CONFIG_9P_FS_POSIX_ACL=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_PRINTK_TIME=y
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_TIMER_STATS=y
+CONFIG_DEBUG_STACK_USAGE=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_BOOT_PRINTK_DELAY=y
+CONFIG_LATENCYTOP=y
+CONFIG_IRQSOFF_TRACER=y
+CONFIG_SCHED_TRACER=y
+CONFIG_STACK_TRACER=y
+CONFIG_BLK_DEV_IO_TRACE=y
+CONFIG_FUNCTION_PROFILER=y
+CONFIG_KGDB=y
+CONFIG_KGDB_KDB=y
+CONFIG_KDB_KEYBOARD=y
+CONFIG_STRICT_DEVMEM=y
+CONFIG_CRYPTO_SEQIV=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_LIBCRC32C=y
--- /dev/null
+++ b/arch/arm/configs/bcmrpi_emergency_defconfig
@@ -0,0 +1,532 @@
+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_FHANDLE=y
+CONFIG_AUDIT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE="../target_fs"
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_RESOURCE_COUNTERS=y
+CONFIG_BLK_CGROUP=y
+CONFIG_NAMESPACES=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_OPROFILE=m
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_BLK_DEV_THROTTLING=y
+CONFIG_CFQ_GROUP_IOSCHED=y
+CONFIG_ARCH_BCM2708=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_AEABI=y
+CONFIG_SECCOMP=y
+CONFIG_CC_STACKPROTECTOR=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext3 rootwait"
+CONFIG_KEXEC=y
+CONFIG_CPU_IDLE=y
+CONFIG_VFP=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_NET_PKTGEN=m
+CONFIG_IRDA=m
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+CONFIG_IRDA_ULTRA=y
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+CONFIG_IRDA_FAST_RR=y
+CONFIG_IRTTY_SIR=m
+CONFIG_KINGSUN_DONGLE=m
+CONFIG_KSDAZZLE_DONGLE=m
+CONFIG_KS959_DONGLE=m
+CONFIG_USB_IRDA=m
+CONFIG_SIGMATEL_FIR=m
+CONFIG_MCS_FIR=m
+CONFIG_BT=m
+CONFIG_BT_L2CAP=y
+CONFIG_BT_SCO=y
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
+CONFIG_BT_ATH3K=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_RC_PID=y
+CONFIG_MAC80211_MESH=y
+CONFIG_WIMAX=m
+CONFIG_NET_9P=m
+CONFIG_NFC=m
+CONFIG_NFC_PN533=m
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_MISC_DEVICES=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=m
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_MD=y
+CONFIG_NETDEVICES=y
+CONFIG_TUN=m
+CONFIG_PHYLIB=m
+CONFIG_MDIO_BITBANG=m
+CONFIG_NET_ETHERNET=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_LIBERTAS_THINFIRM_USB=m
+CONFIG_AT76C50X_USB=m
+CONFIG_USB_ZD1201=m
+CONFIG_USB_NET_RNDIS_WLAN=m
+CONFIG_RTL8187=m
+CONFIG_MAC80211_HWSIM=m
+CONFIG_ATH_COMMON=m
+CONFIG_ATH9K=m
+CONFIG_ATH9K_HTC=m
+CONFIG_CARL9170=m
+CONFIG_B43=m
+CONFIG_B43LEGACY=m
+CONFIG_HOSTAP=m
+CONFIG_IWM=m
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_P54_COMMON=m
+CONFIG_P54_USB=m
+CONFIG_RT2X00=m
+CONFIG_RT2500USB=m
+CONFIG_RT73USB=m
+CONFIG_RT2800USB=m
+CONFIG_RT2800USB_RT53XX=y
+CONFIG_RTL8192CU=m
+CONFIG_WL1251=m
+CONFIG_WL12XX_MENU=m
+CONFIG_ZD1211RW=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_WIMAX_I2400M_USB=m
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=y
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+CONFIG_USB_NET_CDC_EEM=m
+CONFIG_USB_NET_DM9601=m
+CONFIG_USB_NET_SMSC75XX=m
+CONFIG_USB_NET_SMSC95XX=y
+CONFIG_USB_NET_GL620A=m
+CONFIG_USB_NET_NET1080=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_USB_NET_CDC_SUBSET=m
+CONFIG_USB_ALI_M5632=y
+CONFIG_USB_AN2720=y
+CONFIG_USB_KC2190=y
+# CONFIG_USB_NET_ZAURUS is not set
+CONFIG_USB_NET_CX82310_ETH=m
+CONFIG_USB_NET_KALMIA=m
+CONFIG_USB_NET_INT51X1=m
+CONFIG_USB_IPHETH=m
+CONFIG_USB_SIERRA_NET=m
+CONFIG_USB_VL600=m
+CONFIG_PPP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_NETCONSOLE=m
+CONFIG_INPUT_POLLDEV=m
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_JOYDEV=m
+CONFIG_INPUT_EVDEV=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AD714X=m
+CONFIG_INPUT_ATI_REMOTE=m
+CONFIG_INPUT_ATI_REMOTE2=m
+CONFIG_INPUT_KEYSPAN_REMOTE=m
+CONFIG_INPUT_POWERMATE=m
+CONFIG_INPUT_YEALINK=m
+CONFIG_INPUT_CM109=m
+CONFIG_INPUT_UINPUT=m
+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
+CONFIG_INPUT_ADXL34X=m
+CONFIG_INPUT_CMA3000=m
+CONFIG_SERIO=m
+CONFIG_SERIO_RAW=m
+CONFIG_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_RAW_DRIVER=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_BCM2708_WDT=m
+# CONFIG_MFD_SUPPORT is not set
+CONFIG_FB=y
+CONFIG_FB_BCM2708=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_HRTIMER=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_ALOOP=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+CONFIG_SND_BCM2835=m
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_UA101=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_6FIRE=m
+CONFIG_SOUND_PRIME=m
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_ACRUX=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_DRAGONRISE=m
+CONFIG_HID_EMS_FF=m
+CONFIG_HID_ELECOM=m
+CONFIG_HID_EZKEY=m
+CONFIG_HID_HOLTEK=m
+CONFIG_HID_KEYTOUCH=m
+CONFIG_HID_KYE=m
+CONFIG_HID_UCLOGIC=m
+CONFIG_HID_WALTOP=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_TWINHAN=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LCPOWER=m
+CONFIG_HID_LOGITECH=m
+CONFIG_HID_MAGICMOUSE=m
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_MULTITOUCH=m
+CONFIG_HID_NTRIG=m
+CONFIG_HID_ORTEK=m
+CONFIG_HID_PANTHERLORD=m
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_PICOLCD=m
+CONFIG_HID_QUANTA=m
+CONFIG_HID_ROCCAT=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SPEEDLINK=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_GREENASIA=m
+CONFIG_HID_SMARTJOYPLUS=m
+CONFIG_HID_TOPSEED=m
+CONFIG_HID_THRUSTMASTER=m
+CONFIG_HID_WACOM=m
+CONFIG_HID_WIIMOTE=m
+CONFIG_HID_ZEROPLUS=m
+CONFIG_HID_ZYDACRON=m
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_MON=m
+CONFIG_USB_DWCOTG=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_ONETOUCH=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
+CONFIG_USB_STORAGE_ENE_UB6250=m
+CONFIG_USB_UAS=y
+CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_FUNSOFT=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OTI6858=m
+CONFIG_USB_SERIAL_QCAUX=m
+CONFIG_USB_SERIAL_QUALCOMM=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_HP4X=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SIEMENS_MPI=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_SYMBOL=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_VIVOPAY_SERIAL=m
+CONFIG_USB_SERIAL_ZIO=m
+CONFIG_USB_SERIAL_SSU100=m
+CONFIG_USB_SERIAL_DEBUG=m
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+CONFIG_USB_ADUTUX=m
+CONFIG_USB_SEVSEG=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_LED=m
+CONFIG_USB_CYPRESS_CY7C63=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_IDMOUSE=m
+CONFIG_USB_FTDI_ELAN=m
+CONFIG_USB_APPLEDISPLAY=m
+CONFIG_USB_LD=m
+CONFIG_USB_TRANCEVIBRATOR=m
+CONFIG_USB_IOWARRIOR=m
+CONFIG_USB_TEST=m
+CONFIG_USB_ISIGHTFW=m
+CONFIG_USB_YUREX=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM2708=y
+CONFIG_MMC_SDHCI_BCM2708_DMA=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+CONFIG_UIO=m
+CONFIG_UIO_PDRV=m
+CONFIG_UIO_PDRV_GENIRQ=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_JFS_STATISTICS=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_XFS_RT=y
+CONFIG_GFS2_FS=m
+CONFIG_OCFS2_FS=m
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
+CONFIG_NILFS2_FS=m
+CONFIG_FANOTIFY=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
+CONFIG_FSCACHE=y
+CONFIG_FSCACHE_STATS=y
+CONFIG_FSCACHE_HISTOGRAM=y
+CONFIG_CACHEFILES=y
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+CONFIG_NTFS_FS=m
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFS_FSCACHE=y
+CONFIG_CIFS=m
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_9P_FS=m
+CONFIG_9P_FS_POSIX_ACL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_PRINTK_TIME=y
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_TIMER_STATS=y
+CONFIG_DEBUG_STACK_USAGE=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_BOOT_PRINTK_DELAY=y
+CONFIG_LATENCYTOP=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_IRQSOFF_TRACER=y
+CONFIG_SCHED_TRACER=y
+CONFIG_STACK_TRACER=y
+CONFIG_BLK_DEV_IO_TRACE=y
+CONFIG_FUNCTION_PROFILER=y
+CONFIG_KGDB=y
+CONFIG_KGDB_KDB=y
+CONFIG_KDB_KEYBOARD=y
+CONFIG_STRICT_DEVMEM=y
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_SEQIV=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEFLATE=m
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_LIBCRC32C=y
--- /dev/null
+++ b/arch/arm/configs/bcmrpi_quick_defconfig
@@ -0,0 +1,197 @@
+# CONFIG_ARM_PATCH_PHYS_VIRT is not set
+CONFIG_LOCALVERSION="-quick"
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_BCM2708=y
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait"
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_IDLE=y
+CONFIG_VFP=y
+CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_USB_USBNET=y
+# CONFIG_USB_NET_AX8817X is not set
+# CONFIG_USB_NET_CDCETHER is not set
+# CONFIG_USB_NET_CDC_NCM is not set
+CONFIG_USB_NET_SMSC95XX=y
+# CONFIG_USB_NET_NET1080 is not set
+# CONFIG_USB_NET_CDC_SUBSET is not set
+# CONFIG_USB_NET_ZAURUS is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_TTY_PRINTK=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_BCM2708=y
+CONFIG_RAW_DRIVER=y
+CONFIG_THERMAL=y
+CONFIG_THERMAL_BCM2835=y
+CONFIG_WATCHDOG=y
+CONFIG_BCM2708_WDT=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
+CONFIG_REGULATOR_USERSPACE_CONSUMER=y
+CONFIG_FB=y
+CONFIG_FB_BCM2708=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_BCM2835=y
+# CONFIG_SND_USB is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_DWCOTG=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM2708=y
+CONFIG_MMC_SDHCI_BCM2708_DMA=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FSCACHE=y
+CONFIG_CACHEFILES=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFS_FSCACHE=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=y
+CONFIG_NLS_CODEPAGE_775=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_CODEPAGE_852=y
+CONFIG_NLS_CODEPAGE_855=y
+CONFIG_NLS_CODEPAGE_857=y
+CONFIG_NLS_CODEPAGE_860=y
+CONFIG_NLS_CODEPAGE_861=y
+CONFIG_NLS_CODEPAGE_862=y
+CONFIG_NLS_CODEPAGE_863=y
+CONFIG_NLS_CODEPAGE_864=y
+CONFIG_NLS_CODEPAGE_865=y
+CONFIG_NLS_CODEPAGE_866=y
+CONFIG_NLS_CODEPAGE_869=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_CODEPAGE_932=y
+CONFIG_NLS_CODEPAGE_949=y
+CONFIG_NLS_CODEPAGE_874=y
+CONFIG_NLS_ISO8859_8=y
+CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_CODEPAGE_1251=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=y
+CONFIG_NLS_ISO8859_3=y
+CONFIG_NLS_ISO8859_4=y
+CONFIG_NLS_ISO8859_5=y
+CONFIG_NLS_ISO8859_6=y
+CONFIG_NLS_ISO8859_7=y
+CONFIG_NLS_ISO8859_9=y
+CONFIG_NLS_ISO8859_13=y
+CONFIG_NLS_ISO8859_14=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_FS=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+CONFIG_KGDB=y
+CONFIG_KGDB_KDB=y
+# CONFIG_ARM_UNWIND is not set
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_ITU_T=y
+CONFIG_LIBCRC32C=y
--- a/arch/arm/include/asm/fiq.h
+++ b/arch/arm/include/asm/fiq.h
@@ -42,6 +42,7 @@ extern void disable_fiq(int fiq);
/* helpers defined in fiqasm.S: */
extern void __set_fiq_regs(unsigned long const *regs);
extern void __get_fiq_regs(unsigned long *regs);
+extern void __FIQ_Branch(unsigned long *regs);
static inline void set_fiq_regs(struct pt_regs const *regs)
{
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -361,6 +361,23 @@ config ARCH_AT91
This enables support for systems based on Atmel
AT91RM9200 and AT91SAM9* processors.
+config ARCH_BCM2708
+ bool "Broadcom BCM2708 family"
+ select CPU_V6
+ select ARM_AMBA
+ select HAVE_CLK
+ select HAVE_SCHED_CLOCK
+ select NEED_MACH_MEMORY_H
+ select CLKDEV_LOOKUP
+ select ARCH_HAS_CPUFREQ
+ select GENERIC_CLOCKEVENTS
+ select ARM_ERRATA_411920
+ select MACH_BCM2708
+ select VC4
+ select FIQ
+ help
+ This enables support for Broadcom BCM2708 boards.
+
config ARCH_CLPS711X
bool "Cirrus Logic CLPS711x/EP721x/EP731x-based"
select ARCH_REQUIRE_GPIOLIB
@@ -1025,6 +1042,7 @@ source "arch/arm/mach-virt/Kconfig"
source "arch/arm/mach-vt8500/Kconfig"
source "arch/arm/mach-w90x900/Kconfig"
+source "arch/arm/mach-bcm2708/Kconfig"
source "arch/arm/mach-zynq/Kconfig"
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -519,6 +519,14 @@ choice
For more details about semihosting, please see
chapter 8 of DUI0203I_rvct_developer_guide.pdf from ARM Ltd.
+ config DEBUG_BCM2708_UART0
+ bool "Broadcom BCM2708 UART0 (PL011)"
+ depends on MACH_BCM2708
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to UART 0. The port must have been initialised
+ by the boot-loader before use.
+
endchoice
config DEBUG_EXYNOS_UART
--- a/arch/arm/kernel/armksyms.c
+++ b/arch/arm/kernel/armksyms.c
@@ -156,3 +156,7 @@ EXPORT_SYMBOL(__gnu_mcount_nc);
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT
EXPORT_SYMBOL(__pv_phys_offset);
#endif
+
+extern void v6wbi_flush_kern_tlb_range(void);
+EXPORT_SYMBOL(v6wbi_flush_kern_tlb_range);
+
--- a/arch/arm/kernel/fiqasm.S
+++ b/arch/arm/kernel/fiqasm.S
@@ -25,6 +25,9 @@
ENTRY(__set_fiq_regs)
mov r2, #PSR_I_BIT | PSR_F_BIT | FIQ_MODE
mrs r1, cpsr
+@@@@@@@@@@@@@@@ hack: enable the fiq here to keep usb driver happy
+ and r1, #~PSR_F_BIT
+@@@@@@@@@@@@@@@ endhack: (need to find better place for this to happen)
msr cpsr_c, r2 @ select FIQ mode
mov r0, r0 @ avoid hazard prior to ARMv4
ldmia r0!, {r8 - r12}
@@ -47,3 +50,7 @@ ENTRY(__get_fiq_regs)
mov r0, r0 @ avoid hazard prior to ARMv4
mov pc, lr
ENDPROC(__get_fiq_regs)
+
+ENTRY(__FIQ_Branch)
+ mov pc, r8
+ENDPROC(__FIQ_Branch)
--- a/arch/arm/kernel/fiq.c
+++ b/arch/arm/kernel/fiq.c
@@ -141,6 +141,7 @@ void disable_fiq(int fiq)
EXPORT_SYMBOL(set_fiq_handler);
EXPORT_SYMBOL(__set_fiq_regs); /* defined in fiqasm.S */
EXPORT_SYMBOL(__get_fiq_regs); /* defined in fiqasm.S */
+EXPORT_SYMBOL(__FIQ_Branch); /* defined in fiqasm.S */
EXPORT_SYMBOL(claim_fiq);
EXPORT_SYMBOL(release_fiq);
EXPORT_SYMBOL(enable_fiq);
--- /dev/null
+++ b/arch/arm/mach-bcm2708/armctrl.c
@@ -0,0 +1,219 @@
+/*
+ * linux/arch/arm/mach-bcm2708/armctrl.c
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/version.h>
+#include <linux/syscore_ops.h>
+#include <linux/interrupt.h>
+
+#include <asm/mach/irq.h>
+#include <mach/hardware.h>
+#include "armctrl.h"
+
+/* For support of kernels >= 3.0 assume only one VIC for now*/
+static unsigned int remap_irqs[(INTERRUPT_ARASANSDIO + 1) - INTERRUPT_JPEG] = {
+ INTERRUPT_VC_JPEG,
+ INTERRUPT_VC_USB,
+ INTERRUPT_VC_3D,
+ INTERRUPT_VC_DMA2,
+ INTERRUPT_VC_DMA3,
+ INTERRUPT_VC_I2C,
+ INTERRUPT_VC_SPI,
+ INTERRUPT_VC_I2SPCM,
+ INTERRUPT_VC_SDIO,
+ INTERRUPT_VC_UART,
+ INTERRUPT_VC_ARASANSDIO
+};
+
+static void armctrl_mask_irq(struct irq_data *d)
+{
+ static const unsigned int disables[4] = {
+ ARM_IRQ_DIBL1,
+ ARM_IRQ_DIBL2,
+ ARM_IRQ_DIBL3,
+ 0
+ };
+
+ if (d->irq >= FIQ_START) {
+ writel(0, __io_address(ARM_IRQ_FAST));
+ } else {
+ unsigned int data = (unsigned int)irq_get_chip_data(d->irq);
+ writel(1 << (data & 0x1f), __io_address(disables[(data >> 5) & 0x3]));
+ }
+}
+
+static void armctrl_unmask_irq(struct irq_data *d)
+{
+ static const unsigned int enables[4] = {
+ ARM_IRQ_ENBL1,
+ ARM_IRQ_ENBL2,
+ ARM_IRQ_ENBL3,
+ 0
+ };
+
+ if (d->irq >= FIQ_START) {
+ unsigned int data =
+ (unsigned int)irq_get_chip_data(d->irq) - FIQ_START;
+ writel(0x80 | data, __io_address(ARM_IRQ_FAST));
+ } else {
+ unsigned int data = (unsigned int)irq_get_chip_data(d->irq);
+ writel(1 << (data & 0x1f), __io_address(enables[(data >> 5) & 0x3]));
+ }
+}
+
+#if defined(CONFIG_PM)
+
+/* for kernels 3.xx use the new syscore_ops apis but for older kernels use the sys dev class */
+
+/* Static defines
+ * struct armctrl_device - VIC PM device (< 3.xx)
+ * @sysdev: The system device which is registered. (< 3.xx)
+ * @irq: The IRQ number for the base of the VIC.
+ * @base: The register base for the VIC.
+ * @resume_sources: A bitmask of interrupts for resume.
+ * @resume_irqs: The IRQs enabled for resume.
+ * @int_select: Save for VIC_INT_SELECT.
+ * @int_enable: Save for VIC_INT_ENABLE.
+ * @soft_int: Save for VIC_INT_SOFT.
+ * @protect: Save for VIC_PROTECT.
+ */
+struct armctrl_info {
+ void __iomem *base;
+ int irq;
+ u32 resume_sources;
+ u32 resume_irqs;
+ u32 int_select;
+ u32 int_enable;
+ u32 soft_int;
+ u32 protect;
+} armctrl;
+
+static int armctrl_suspend(void)
+{
+ return 0;
+}
+
+static void armctrl_resume(void)
+{
+ return;
+}
+
+/**
+ * armctrl_pm_register - Register a VIC for later power management control
+ * @base: The base address of the VIC.
+ * @irq: The base IRQ for the VIC.
+ * @resume_sources: bitmask of interrupts allowed for resume sources.
+ *
+ * For older kernels (< 3.xx) do -
+ * Register the VIC with the system device tree so that it can be notified
+ * of suspend and resume requests and ensure that the correct actions are
+ * taken to re-instate the settings on resume.
+ */
+static void __init armctrl_pm_register(void __iomem * base, unsigned int irq,
+ u32 resume_sources)
+{
+ armctrl.base = base;
+ armctrl.resume_sources = resume_sources;
+ armctrl.irq = irq;
+}
+
+static int armctrl_set_wake(struct irq_data *d, unsigned int on)
+{
+ unsigned int off = d->irq & 31;
+ u32 bit = 1 << off;
+
+ if (!(bit & armctrl.resume_sources))
+ return -EINVAL;
+
+ if (on)
+ armctrl.resume_irqs |= bit;
+ else
+ armctrl.resume_irqs &= ~bit;
+
+ return 0;
+}
+
+#else
+static inline void armctrl_pm_register(void __iomem * base, unsigned int irq,
+ u32 arg1)
+{
+}
+
+#define armctrl_suspend NULL
+#define armctrl_resume NULL
+#define armctrl_set_wake NULL
+#endif /* CONFIG_PM */
+
+static struct syscore_ops armctrl_syscore_ops = {
+ .suspend = armctrl_suspend,
+ .resume = armctrl_resume,
+};
+
+/**
+ * armctrl_syscore_init - initicall to register VIC pm functions
+ *
+ * This is called via late_initcall() to register
+ * the resources for the VICs due to the early
+ * nature of the VIC's registration.
+*/
+static int __init armctrl_syscore_init(void)
+{
+ register_syscore_ops(&armctrl_syscore_ops);
+ return 0;
+}
+
+late_initcall(armctrl_syscore_init);
+
+static struct irq_chip armctrl_chip = {
+ .name = "ARMCTRL",
+ .irq_ack = armctrl_mask_irq,
+ .irq_mask = armctrl_mask_irq,
+ .irq_unmask = armctrl_unmask_irq,
+ .irq_set_wake = armctrl_set_wake,
+};
+
+/**
+ * armctrl_init - initialise a vectored interrupt controller
+ * @base: iomem base address
+ * @irq_start: starting interrupt number, must be muliple of 32
+ * @armctrl_sources: bitmask of interrupt sources to allow
+ * @resume_sources: bitmask of interrupt sources to allow for resume
+ */
+int __init armctrl_init(void __iomem * base, unsigned int irq_start,
+ u32 armctrl_sources, u32 resume_sources)
+{
+ unsigned int irq;
+
+ for (irq = 0; irq < NR_IRQS; irq++) {
+ unsigned int data = irq;
+ if (irq >= INTERRUPT_JPEG && irq <= INTERRUPT_ARASANSDIO)
+ data = remap_irqs[irq - INTERRUPT_JPEG];
+
+ irq_set_chip(irq, &armctrl_chip);
+ irq_set_chip_data(irq, (void *)data);
+ irq_set_handler(irq, handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE | IRQF_DISABLED);
+ }
+
+ armctrl_pm_register(base, irq_start, resume_sources);
+ init_FIQ(FIQ_START);
+ return 0;
+}
--- /dev/null
+++ b/arch/arm/mach-bcm2708/armctrl.h
@@ -0,0 +1,27 @@
+/*
+ * linux/arch/arm/mach-bcm2708/armctrl.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __BCM2708_ARMCTRL_H
+#define __BCM2708_ARMCTRL_H
+
+extern int __init armctrl_init(void __iomem * base, unsigned int irq_start,
+ u32 armctrl_sources, u32 resume_sources);
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/bcm2708.c
@@ -0,0 +1,885 @@
+/*
+ * linux/arch/arm/mach-bcm2708/bcm2708.c
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/serial_8250.h>
+#include <linux/platform_device.h>
+#include <linux/syscore_ops.h>
+#include <linux/interrupt.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/clcd.h>
+#include <linux/clockchips.h>
+#include <linux/cnt32_to_63.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/w1-gpio.h>
+
+#include <linux/version.h>
+#include <linux/clkdev.h>
+#include <asm/system.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/sched_clock.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/time.h>
+#include <asm/mach/map.h>
+
+#include <mach/timex.h>
+#include <mach/dma.h>
+#include <mach/vcio.h>
+#include <mach/system.h>
+
+#include <linux/delay.h>
+
+#include "bcm2708.h"
+#include "armctrl.h"
+#include "clock.h"
+
+#ifdef CONFIG_BCM_VC_CMA
+#include <linux/broadcom/vc_cma.h>
+#endif
+
+
+/* Effectively we have an IOMMU (ARM<->VideoCore map) that is set up to
+ * give us IO access only to 64Mbytes of physical memory (26 bits). We could
+ * represent this window by setting our dmamasks to 26 bits but, in fact
+ * we're not going to use addresses outside this range (they're not in real
+ * memory) so we don't bother.
+ *
+ * In the future we might include code to use this IOMMU to remap other
+ * physical addresses onto VideoCore memory then the use of 32-bits would be
+ * more legitimate.
+ */
+#define DMA_MASK_BITS_COMMON 32
+
+// use GPIO 4 for the one-wire GPIO pin, if enabled
+#define W1_GPIO 4
+
+/* command line parameters */
+static unsigned boardrev, serial;
+static unsigned uart_clock;
+
+static void __init bcm2708_init_led(void);
+
+void __init bcm2708_init_irq(void)
+{
+ armctrl_init(__io_address(ARMCTRL_IC_BASE), 0, 0, 0);
+}
+
+static struct map_desc bcm2708_io_desc[] __initdata = {
+ {
+ .virtual = IO_ADDRESS(ARMCTRL_BASE),
+ .pfn = __phys_to_pfn(ARMCTRL_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(UART0_BASE),
+ .pfn = __phys_to_pfn(UART0_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(UART1_BASE),
+ .pfn = __phys_to_pfn(UART1_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(DMA_BASE),
+ .pfn = __phys_to_pfn(DMA_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(MCORE_BASE),
+ .pfn = __phys_to_pfn(MCORE_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(ST_BASE),
+ .pfn = __phys_to_pfn(ST_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(USB_BASE),
+ .pfn = __phys_to_pfn(USB_BASE),
+ .length = SZ_128K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(PM_BASE),
+ .pfn = __phys_to_pfn(PM_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE},
+ {
+ .virtual = IO_ADDRESS(GPIO_BASE),
+ .pfn = __phys_to_pfn(GPIO_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE}
+};
+
+void __init bcm2708_map_io(void)
+{
+ iotable_init(bcm2708_io_desc, ARRAY_SIZE(bcm2708_io_desc));
+}
+
+/* The STC is a free running counter that increments at the rate of 1MHz */
+#define STC_FREQ_HZ 1000000
+
+static inline uint32_t timer_read(void)
+{
+ /* STC: a free running counter that increments at the rate of 1MHz */
+ return readl(__io_address(ST_BASE + 0x04));
+}
+
+static unsigned long bcm2708_read_current_timer(void)
+{
+ return timer_read();
+}
+
+static u32 notrace bcm2708_read_sched_clock(void)
+{
+ return timer_read();
+}
+
+static cycle_t clksrc_read(struct clocksource *cs)
+{
+ return timer_read();
+}
+
+static struct clocksource clocksource_stc = {
+ .name = "stc",
+ .rating = 300,
+ .read = clksrc_read,
+ .mask = CLOCKSOURCE_MASK(32),
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+unsigned long frc_clock_ticks32(void)
+{
+ return timer_read();
+}
+
+static void __init bcm2708_clocksource_init(void)
+{
+ if (clocksource_register_hz(&clocksource_stc, STC_FREQ_HZ)) {
+ printk(KERN_ERR "timer: failed to initialize clock "
+ "source %s\n", clocksource_stc.name);
+ }
+}
+
+
+/*
+ * These are fixed clocks.
+ */
+static struct clk ref24_clk = {
+ .rate = UART0_CLOCK, /* The UART is clocked at 3MHz via APB_CLK */
+};
+
+static struct clk osc_clk = {
+#ifdef CONFIG_ARCH_BCM2708_CHIPIT
+ .rate = 27000000,
+#else
+ .rate = 500000000, /* ARM clock is set from the VideoCore booter */
+#endif
+};
+
+/* warning - the USB needs a clock > 34MHz */
+
+static struct clk sdhost_clk = {
+#ifdef CONFIG_ARCH_BCM2708_CHIPIT
+ .rate = 4000000, /* 4MHz */
+#else
+ .rate = 250000000, /* 250MHz */
+#endif
+};
+
+static struct clk_lookup lookups[] = {
+ { /* UART0 */
+ .dev_id = "dev:f1",
+ .clk = &ref24_clk,
+ },
+ { /* USB */
+ .dev_id = "bcm2708_usb",
+ .clk = &osc_clk,
+ }, { /* SPI */
+ .dev_id = "bcm2708_spi.0",
+ .clk = &sdhost_clk,
+ }, { /* BSC0 */
+ .dev_id = "bcm2708_i2c.0",
+ .clk = &sdhost_clk,
+ }, { /* BSC1 */
+ .dev_id = "bcm2708_i2c.1",
+ .clk = &sdhost_clk,
+ }
+};
+
+#define UART0_IRQ { IRQ_UART, 0 /*NO_IRQ*/ }
+#define UART0_DMA { 15, 14 }
+
+AMBA_DEVICE(uart0, "dev:f1", UART0, NULL);
+
+static struct amba_device *amba_devs[] __initdata = {
+ &uart0_device,
+};
+
+static struct resource bcm2708_dmaman_resources[] = {
+ {
+ .start = DMA_BASE,
+ .end = DMA_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
+static struct platform_device bcm2708_dmaman_device = {
+ .name = BCM_DMAMAN_DRIVER_NAME,
+ .id = 0, /* first bcm2708_dma */
+ .resource = bcm2708_dmaman_resources,
+ .num_resources = ARRAY_SIZE(bcm2708_dmaman_resources),
+};
+
+#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
+static struct w1_gpio_platform_data w1_gpio_pdata = {
+ .pin = W1_GPIO,
+ .is_open_drain = 0,
+};
+
+static struct platform_device w1_device = {
+ .name = "w1-gpio",
+ .id = -1,
+ .dev.platform_data = &w1_gpio_pdata,
+};
+#endif
+
+static u64 fb_dmamask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON);
+
+static struct platform_device bcm2708_fb_device = {
+ .name = "bcm2708_fb",
+ .id = -1, /* only one bcm2708_fb */
+ .resource = NULL,
+ .num_resources = 0,
+ .dev = {
+ .dma_mask = &fb_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON),
+ },
+};
+
+static struct plat_serial8250_port bcm2708_uart1_platform_data[] = {
+ {
+ .mapbase = UART1_BASE + 0x40,
+ .irq = IRQ_AUX,
+ .uartclk = 125000000,
+ .regshift = 2,
+ .iotype = UPIO_MEM,
+ .flags = UPF_FIXED_TYPE | UPF_IOREMAP | UPF_SKIP_TEST,
+ .type = PORT_8250,
+ },
+ {},
+};
+
+static struct platform_device bcm2708_uart1_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = bcm2708_uart1_platform_data,
+ },
+};
+
+static struct resource bcm2708_usb_resources[] = {
+ [0] = {
+ .start = USB_BASE,
+ .end = USB_BASE + SZ_128K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = MPHI_BASE,
+ .end = MPHI_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = IRQ_HOSTPORT,
+ .end = IRQ_HOSTPORT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+bool fiq_fix_enable = true;
+
+static struct resource bcm2708_usb_resources_no_fiq_fix[] = {
+ [0] = {
+ .start = USB_BASE,
+ .end = USB_BASE + SZ_128K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_USB,
+ .end = IRQ_USB,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 usb_dmamask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON);
+
+static struct platform_device bcm2708_usb_device = {
+ .name = "bcm2708_usb",
+ .id = -1, /* only one bcm2708_usb */
+ .resource = bcm2708_usb_resources,
+ .num_resources = ARRAY_SIZE(bcm2708_usb_resources),
+ .dev = {
+ .dma_mask = &usb_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON),
+ },
+};
+
+static struct resource bcm2708_vcio_resources[] = {
+ [0] = { /* mailbox/semaphore/doorbell access */
+ .start = MCORE_BASE,
+ .end = MCORE_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static u64 vcio_dmamask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON);
+
+static struct platform_device bcm2708_vcio_device = {
+ .name = BCM_VCIO_DRIVER_NAME,
+ .id = -1, /* only one VideoCore I/O area */
+ .resource = bcm2708_vcio_resources,
+ .num_resources = ARRAY_SIZE(bcm2708_vcio_resources),
+ .dev = {
+ .dma_mask = &vcio_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON),
+ },
+};
+
+#ifdef CONFIG_BCM2708_GPIO
+#define BCM_GPIO_DRIVER_NAME "bcm2708_gpio"
+
+static struct resource bcm2708_gpio_resources[] = {
+ [0] = { /* general purpose I/O */
+ .start = GPIO_BASE,
+ .end = GPIO_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static u64 gpio_dmamask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON);
+
+static struct platform_device bcm2708_gpio_device = {
+ .name = BCM_GPIO_DRIVER_NAME,
+ .id = -1, /* only one VideoCore I/O area */
+ .resource = bcm2708_gpio_resources,
+ .num_resources = ARRAY_SIZE(bcm2708_gpio_resources),
+ .dev = {
+ .dma_mask = &gpio_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON),
+ },
+};
+#endif
+
+static struct resource bcm2708_systemtimer_resources[] = {
+ [0] = { /* system timer access */
+ .start = ST_BASE,
+ .end = ST_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_TIMER3,
+ .end = IRQ_TIMER3,
+ .flags = IORESOURCE_IRQ,
+ }
+
+};
+
+static u64 systemtimer_dmamask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON);
+
+static struct platform_device bcm2708_systemtimer_device = {
+ .name = "bcm2708_systemtimer",
+ .id = -1, /* only one VideoCore I/O area */
+ .resource = bcm2708_systemtimer_resources,
+ .num_resources = ARRAY_SIZE(bcm2708_systemtimer_resources),
+ .dev = {
+ .dma_mask = &systemtimer_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON),
+ },
+};
+
+#ifdef CONFIG_MMC_SDHCI_BCM2708 /* Arasan emmc SD */
+static struct resource bcm2708_emmc_resources[] = {
+ [0] = {
+ .start = EMMC_BASE,
+ .end = EMMC_BASE + SZ_256 - 1, /* we only need this area */
+ /* the memory map actually makes SZ_4K available */
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_ARASANSDIO,
+ .end = IRQ_ARASANSDIO,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 bcm2708_emmc_dmamask = 0xffffffffUL;
+
+struct platform_device bcm2708_emmc_device = {
+ .name = "bcm2708_sdhci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bcm2708_emmc_resources),
+ .resource = bcm2708_emmc_resources,
+ .dev = {
+ .dma_mask = &bcm2708_emmc_dmamask,
+ .coherent_dma_mask = 0xffffffffUL},
+};
+#endif /* CONFIG_MMC_SDHCI_BCM2708 */
+
+static struct resource bcm2708_powerman_resources[] = {
+ [0] = {
+ .start = PM_BASE,
+ .end = PM_BASE + SZ_256 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static u64 powerman_dmamask = DMA_BIT_MASK(DMA_MASK_BITS_COMMON);
+
+struct platform_device bcm2708_powerman_device = {
+ .name = "bcm2708_powerman",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bcm2708_powerman_resources),
+ .resource = bcm2708_powerman_resources,
+ .dev = {
+ .dma_mask = &powerman_dmamask,
+ .coherent_dma_mask = 0xffffffffUL},
+};
+
+
+static struct platform_device bcm2708_alsa_devices[] = {
+ [0] = {
+ .name = "bcm2835_AUD0",
+ .id = 0, /* first audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+ [1] = {
+ .name = "bcm2835_AUD1",
+ .id = 1, /* second audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+ [2] = {
+ .name = "bcm2835_AUD2",
+ .id = 2, /* third audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+ [3] = {
+ .name = "bcm2835_AUD3",
+ .id = 3, /* forth audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+ [4] = {
+ .name = "bcm2835_AUD4",
+ .id = 4, /* fifth audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+ [5] = {
+ .name = "bcm2835_AUD5",
+ .id = 5, /* sixth audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+ [6] = {
+ .name = "bcm2835_AUD6",
+ .id = 6, /* seventh audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+ [7] = {
+ .name = "bcm2835_AUD7",
+ .id = 7, /* eighth audio device */
+ .resource = 0,
+ .num_resources = 0,
+ },
+};
+
+static struct resource bcm2708_spi_resources[] = {
+ {
+ .start = SPI0_BASE,
+ .end = SPI0_BASE + SZ_256 - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+
+static struct platform_device bcm2708_spi_device = {
+ .name = "bcm2708_spi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bcm2708_spi_resources),
+ .resource = bcm2708_spi_resources,
+};
+
+#ifdef CONFIG_BCM2708_SPIDEV
+static struct spi_board_info bcm2708_spi_devices[] = {
+#ifdef CONFIG_SPI_SPIDEV
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 500000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = SPI_MODE_0,
+ }, {
+ .modalias = "spidev",
+ .max_speed_hz = 500000,
+ .bus_num = 0,
+ .chip_select = 1,
+ .mode = SPI_MODE_0,
+ }
+#endif
+};
+#endif
+
+static struct resource bcm2708_bsc0_resources[] = {
+ {
+ .start = BSC0_BASE,
+ .end = BSC0_BASE + SZ_256 - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = INTERRUPT_I2C,
+ .end = INTERRUPT_I2C,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device bcm2708_bsc0_device = {
+ .name = "bcm2708_i2c",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bcm2708_bsc0_resources),
+ .resource = bcm2708_bsc0_resources,
+};
+
+
+static struct resource bcm2708_bsc1_resources[] = {
+ {
+ .start = BSC1_BASE,
+ .end = BSC1_BASE + SZ_256 - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = INTERRUPT_I2C,
+ .end = INTERRUPT_I2C,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device bcm2708_bsc1_device = {
+ .name = "bcm2708_i2c",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bcm2708_bsc1_resources),
+ .resource = bcm2708_bsc1_resources,
+};
+
+static struct platform_device bcm2835_hwmon_device = {
+ .name = "bcm2835_hwmon",
+};
+
+static struct platform_device bcm2835_thermal_device = {
+ .name = "bcm2835_thermal",
+};
+
+int __init bcm_register_device(struct platform_device *pdev)
+{
+ int ret;
+
+ ret = platform_device_register(pdev);
+ if (ret)
+ pr_debug("Unable to register platform device '%s': %d\n",
+ pdev->name, ret);
+
+ return ret;
+}
+
+static void bcm2708_restart(char mode, const char *cmd)
+{
+ uint32_t pm_rstc, pm_wdog;
+ uint32_t timeout = 10;
+
+ /* For quick reset notification add reboot=q to cmdline
+ */
+ if(mode == 'q')
+ {
+ uint32_t pm_rsts = readl(__io_address(PM_RSTS));
+ pm_rsts = PM_PASSWORD | pm_rsts | PM_RSTS_HADWRQ_SET;
+ writel(pm_rsts, __io_address(PM_RSTS));
+ }
+
+ /* Setup watchdog for reset */
+ pm_rstc = readl(__io_address(PM_RSTC));
+
+ pm_wdog = PM_PASSWORD | (timeout & PM_WDOG_TIME_SET); // watchdog timer = timer clock / 16; need password (31:16) + value (11:0)
+ pm_rstc = PM_PASSWORD | (pm_rstc & PM_RSTC_WRCFG_CLR) | PM_RSTC_WRCFG_FULL_RESET;
+
+ writel(pm_wdog, __io_address(PM_WDOG));
+ writel(pm_rstc, __io_address(PM_RSTC));
+}
+
+/* We can't really power off, but if we do the normal reset scheme, and indicate to bootcode.bin not to reboot, then most of the chip will be powered off */
+static void bcm2708_power_off(void)
+{
+ /* we set the watchdog hard reset bit here to distinguish this reset from the normal (full) reset. bootcode.bin will not reboot after a hard reset */
+ uint32_t pm_rsts = readl(__io_address(PM_RSTS));
+ pm_rsts = PM_PASSWORD | (pm_rsts & PM_RSTC_WRCFG_CLR) | PM_RSTS_HADWRH_SET;
+ writel(pm_rsts, __io_address(PM_RSTS));
+ /* continue with normal reset mechanism */
+ bcm2708_restart(0, "");
+}
+
+void __init bcm2708_init(void)
+{
+ int i;
+
+#if defined(CONFIG_BCM_VC_CMA)
+ vc_cma_early_init();
+#endif
+ printk("bcm2708.uart_clock = %d\n", uart_clock);
+ pm_power_off = bcm2708_power_off;
+
+ if (uart_clock)
+ lookups[0].clk->rate = uart_clock;
+
+ for (i = 0; i < ARRAY_SIZE(lookups); i++)
+ clkdev_add(&lookups[i]);
+
+ bcm_register_device(&bcm2708_dmaman_device);
+ bcm_register_device(&bcm2708_vcio_device);
+#ifdef CONFIG_BCM2708_GPIO
+ bcm_register_device(&bcm2708_gpio_device);
+#endif
+#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
+ platform_device_register(&w1_device);
+#endif
+ bcm_register_device(&bcm2708_systemtimer_device);
+ bcm_register_device(&bcm2708_fb_device);
+ if (!fiq_fix_enable)
+ {
+ bcm2708_usb_device.resource = bcm2708_usb_resources_no_fiq_fix;
+ bcm2708_usb_device.num_resources = ARRAY_SIZE(bcm2708_usb_resources_no_fiq_fix);
+ }
+ bcm_register_device(&bcm2708_usb_device);
+ bcm_register_device(&bcm2708_uart1_device);
+ bcm_register_device(&bcm2708_powerman_device);
+
+#ifdef CONFIG_MMC_SDHCI_BCM2708
+ bcm_register_device(&bcm2708_emmc_device);
+#endif
+ bcm2708_init_led();
+ for (i = 0; i < ARRAY_SIZE(bcm2708_alsa_devices); i++)
+ bcm_register_device(&bcm2708_alsa_devices[i]);
+
+ bcm_register_device(&bcm2708_spi_device);
+ bcm_register_device(&bcm2708_bsc0_device);
+ bcm_register_device(&bcm2708_bsc1_device);
+
+ bcm_register_device(&bcm2835_hwmon_device);
+ bcm_register_device(&bcm2835_thermal_device);
+
+ for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
+ struct amba_device *d = amba_devs[i];
+ amba_device_register(d, &iomem_resource);
+ }
+ system_rev = boardrev;
+ system_serial_low = serial;
+
+#ifdef CONFIG_BCM2708_SPIDEV
+ spi_register_board_info(bcm2708_spi_devices,
+ ARRAY_SIZE(bcm2708_spi_devices));
+#endif
+}
+
+static void timer_set_mode(enum clock_event_mode mode,
+ struct clock_event_device *clk)
+{
+ switch (mode) {
+ case CLOCK_EVT_MODE_ONESHOT: /* Leave the timer disabled, .set_next_event will enable it */
+ case CLOCK_EVT_MODE_SHUTDOWN:
+ break;
+ case CLOCK_EVT_MODE_PERIODIC:
+
+ case CLOCK_EVT_MODE_UNUSED:
+ case CLOCK_EVT_MODE_RESUME:
+
+ default:
+ printk(KERN_ERR "timer_set_mode: unhandled mode:%d\n",
+ (int)mode);
+ break;
+ }
+
+}
+
+static int timer_set_next_event(unsigned long cycles,
+ struct clock_event_device *unused)
+{
+ unsigned long stc;
+
+ stc = readl(__io_address(ST_BASE + 0x04));
+ writel(stc + cycles, __io_address(ST_BASE + 0x18)); /* stc3 */
+ return 0;
+}
+
+static struct clock_event_device timer0_clockevent = {
+ .name = "timer0",
+ .shift = 32,
+ .features = CLOCK_EVT_FEAT_ONESHOT,
+ .set_mode = timer_set_mode,
+ .set_next_event = timer_set_next_event,
+};
+
+/*
+ * IRQ handler for the timer
+ */
+static irqreturn_t bcm2708_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = &timer0_clockevent;
+
+ writel(1 << 3, __io_address(ST_BASE + 0x00)); /* stcs clear timer int */
+
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction bcm2708_timer_irq = {
+ .name = "BCM2708 Timer Tick",
+ .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+ .handler = bcm2708_timer_interrupt,
+};
+
+/*
+ * Set up timer interrupt, and return the current time in seconds.
+ */
+
+static struct delay_timer bcm2708_delay_timer = {
+ .read_current_timer = bcm2708_read_current_timer,
+ .freq = STC_FREQ_HZ,
+};
+
+static void __init bcm2708_timer_init(void)
+{
+ /* init high res timer */
+ bcm2708_clocksource_init();
+
+ /*
+ * Initialise to a known state (all timers off)
+ */
+ writel(0, __io_address(ARM_T_CONTROL));
+ /*
+ * Make irqs happen for the system timer
+ */
+ setup_irq(IRQ_TIMER3, &bcm2708_timer_irq);
+
+ setup_sched_clock(bcm2708_read_sched_clock, 32, STC_FREQ_HZ);
+
+ timer0_clockevent.mult =
+ div_sc(STC_FREQ_HZ, NSEC_PER_SEC, timer0_clockevent.shift);
+ timer0_clockevent.max_delta_ns =
+ clockevent_delta2ns(0xffffffff, &timer0_clockevent);
+ timer0_clockevent.min_delta_ns =
+ clockevent_delta2ns(0xf, &timer0_clockevent);
+
+ timer0_clockevent.cpumask = cpumask_of(0);
+ clockevents_register_device(&timer0_clockevent);
+
+ register_current_timer_delay(&bcm2708_delay_timer);
+}
+
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+#include <linux/leds.h>
+
+static struct gpio_led bcm2708_leds[] = {
+ [0] = {
+ .gpio = 16,
+ .name = "led0",
+ .default_trigger = "mmc0",
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led_platform_data bcm2708_led_pdata = {
+ .num_leds = ARRAY_SIZE(bcm2708_leds),
+ .leds = bcm2708_leds,
+};
+
+static struct platform_device bcm2708_led_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &bcm2708_led_pdata,
+ },
+};
+
+static void __init bcm2708_init_led(void)
+{
+ platform_device_register(&bcm2708_led_device);
+}
+#else
+static inline void bcm2708_init_led(void)
+{
+}
+#endif
+
+void __init bcm2708_init_early(void)
+{
+ /*
+ * Some devices allocate their coherent buffers from atomic
+ * context. Increase size of atomic coherent pool to make sure such
+ * the allocations won't fail.
+ */
+ init_dma_coherent_pool_size(SZ_4M);
+}
+
+static void __init board_reserve(void)
+{
+#if defined(CONFIG_BCM_VC_CMA)
+ vc_cma_reserve();
+#endif
+}
+
+MACHINE_START(BCM2708, "BCM2708")
+ /* Maintainer: Broadcom Europe Ltd. */
+ .map_io = bcm2708_map_io,
+ .init_irq = bcm2708_init_irq,
+ .init_time = bcm2708_timer_init,
+ .init_machine = bcm2708_init,
+ .init_early = bcm2708_init_early,
+ .reserve = board_reserve,
+ .restart = bcm2708_restart,
+MACHINE_END
+
+module_param(boardrev, uint, 0644);
+module_param(serial, uint, 0644);
+module_param(uart_clock, uint, 0644);
--- /dev/null
+++ b/arch/arm/mach-bcm2708/bcm2708_gpio.c
@@ -0,0 +1,339 @@
+/*
+ * linux/arch/arm/mach-bcm2708/bcm2708_gpio.c
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <mach/gpio.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <mach/platform.h>
+
+#define BCM_GPIO_DRIVER_NAME "bcm2708_gpio"
+#define DRIVER_NAME BCM_GPIO_DRIVER_NAME
+#define BCM_GPIO_USE_IRQ 1
+
+#define GPIOFSEL(x) (0x00+(x)*4)
+#define GPIOSET(x) (0x1c+(x)*4)
+#define GPIOCLR(x) (0x28+(x)*4)
+#define GPIOLEV(x) (0x34+(x)*4)
+#define GPIOEDS(x) (0x40+(x)*4)
+#define GPIOREN(x) (0x4c+(x)*4)
+#define GPIOFEN(x) (0x58+(x)*4)
+#define GPIOHEN(x) (0x64+(x)*4)
+#define GPIOLEN(x) (0x70+(x)*4)
+#define GPIOAREN(x) (0x7c+(x)*4)
+#define GPIOAFEN(x) (0x88+(x)*4)
+#define GPIOUD(x) (0x94+(x)*4)
+#define GPIOUDCLK(x) (0x98+(x)*4)
+
+enum { GPIO_FSEL_INPUT, GPIO_FSEL_OUTPUT,
+ GPIO_FSEL_ALT5, GPIO_FSEL_ALT_4,
+ GPIO_FSEL_ALT0, GPIO_FSEL_ALT1,
+ GPIO_FSEL_ALT2, GPIO_FSEL_ALT3,
+};
+
+ /* Each of the two spinlocks protects a different set of hardware
+ * regiters and data structurs. This decouples the code of the IRQ from
+ * the GPIO code. This also makes the case of a GPIO routine call from
+ * the IRQ code simpler.
+ */
+static DEFINE_SPINLOCK(lock); /* GPIO registers */
+
+struct bcm2708_gpio {
+ struct list_head list;
+ void __iomem *base;
+ struct gpio_chip gc;
+ unsigned long rising;
+ unsigned long falling;
+};
+
+static int bcm2708_set_function(struct gpio_chip *gc, unsigned offset,
+ int function)
+{
+ struct bcm2708_gpio *gpio = container_of(gc, struct bcm2708_gpio, gc);
+ unsigned long flags;
+ unsigned gpiodir;
+ unsigned gpio_bank = offset / 10;
+ unsigned gpio_field_offset = (offset - 10 * gpio_bank) * 3;
+
+//printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_set_function %p (%d,%d)\n", gc, offset, function);
+ if (offset >= ARCH_NR_GPIOS)
+ return -EINVAL;
+
+ spin_lock_irqsave(&lock, flags);
+
+ gpiodir = readl(gpio->base + GPIOFSEL(gpio_bank));
+ gpiodir &= ~(7 << gpio_field_offset);
+ gpiodir |= function << gpio_field_offset;
+ writel(gpiodir, gpio->base + GPIOFSEL(gpio_bank));
+ spin_unlock_irqrestore(&lock, flags);
+ gpiodir = readl(gpio->base + GPIOFSEL(gpio_bank));
+
+ return 0;
+}
+
+static int bcm2708_gpio_dir_in(struct gpio_chip *gc, unsigned offset)
+{
+ return bcm2708_set_function(gc, offset, GPIO_FSEL_INPUT);
+}
+
+static void bcm2708_gpio_set(struct gpio_chip *gc, unsigned offset, int value);
+static int bcm2708_gpio_dir_out(struct gpio_chip *gc, unsigned offset,
+ int value)
+{
+ int ret;
+ ret = bcm2708_set_function(gc, offset, GPIO_FSEL_OUTPUT);
+ if (ret >= 0)
+ bcm2708_gpio_set(gc, offset, value);
+ return ret;
+}
+
+static int bcm2708_gpio_get(struct gpio_chip *gc, unsigned offset)
+{
+ struct bcm2708_gpio *gpio = container_of(gc, struct bcm2708_gpio, gc);
+ unsigned gpio_bank = offset / 32;
+ unsigned gpio_field_offset = (offset - 32 * gpio_bank);
+ unsigned lev;
+
+ if (offset >= ARCH_NR_GPIOS)
+ return 0;
+ lev = readl(gpio->base + GPIOLEV(gpio_bank));
+//printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_get %p (%d)=%d\n", gc, offset, 0x1 & (lev>>gpio_field_offset));
+ return 0x1 & (lev >> gpio_field_offset);
+}
+
+static void bcm2708_gpio_set(struct gpio_chip *gc, unsigned offset, int value)
+{
+ struct bcm2708_gpio *gpio = container_of(gc, struct bcm2708_gpio, gc);
+ unsigned gpio_bank = offset / 32;
+ unsigned gpio_field_offset = (offset - 32 * gpio_bank);
+//printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_set %p (%d=%d)\n", gc, offset, value);
+ if (offset >= ARCH_NR_GPIOS)
+ return;
+ if (value)
+ writel(1 << gpio_field_offset, gpio->base + GPIOSET(gpio_bank));
+ else
+ writel(1 << gpio_field_offset, gpio->base + GPIOCLR(gpio_bank));
+}
+
+/*************************************************************************************************************************
+ * bcm2708 GPIO IRQ
+ */
+
+#if BCM_GPIO_USE_IRQ
+
+static int bcm2708_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
+{
+ return gpio_to_irq(gpio);
+}
+
+static int bcm2708_gpio_irq_set_type(struct irq_data *d, unsigned type)
+{
+ unsigned irq = d->irq;
+ struct bcm2708_gpio *gpio = irq_get_chip_data(irq);
+
+ if (type & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
+ return -EINVAL;
+
+ if (type & IRQ_TYPE_EDGE_RISING) {
+ gpio->rising |= (1 << irq_to_gpio(irq));
+ } else {
+ gpio->rising &= ~(1 << irq_to_gpio(irq));
+ }
+
+ if (type & IRQ_TYPE_EDGE_FALLING) {
+ gpio->falling |= (1 << irq_to_gpio(irq));
+ } else {
+ gpio->falling &= ~(1 << irq_to_gpio(irq));
+ }
+ return 0;
+}
+
+static void bcm2708_gpio_irq_mask(struct irq_data *d)
+{
+ unsigned irq = d->irq;
+ struct bcm2708_gpio *gpio = irq_get_chip_data(irq);
+ unsigned gn = irq_to_gpio(irq);
+ unsigned gb = gn / 32;
+ unsigned long rising = readl(gpio->base + GPIOREN(gb));
+ unsigned long falling = readl(gpio->base + GPIOFEN(gb));
+
+ gn = gn % 32;
+
+ writel(rising & ~(1 << gn), gpio->base + GPIOREN(gb));
+ writel(falling & ~(1 << gn), gpio->base + GPIOFEN(gb));
+}
+
+static void bcm2708_gpio_irq_unmask(struct irq_data *d)
+{
+ unsigned irq = d->irq;
+ struct bcm2708_gpio *gpio = irq_get_chip_data(irq);
+ unsigned gn = irq_to_gpio(irq);
+ unsigned gb = gn / 32;
+ unsigned long rising = readl(gpio->base + GPIOREN(gb));
+ unsigned long falling = readl(gpio->base + GPIOFEN(gb));
+
+ gn = gn % 32;
+
+ writel(1 << gn, gpio->base + GPIOEDS(gb));
+
+ if (gpio->rising & (1 << gn)) {
+ writel(rising | (1 << gn), gpio->base + GPIOREN(gb));
+ } else {
+ writel(rising & ~(1 << gn), gpio->base + GPIOREN(gb));
+ }
+
+ if (gpio->falling & (1 << gn)) {
+ writel(falling | (1 << gn), gpio->base + GPIOFEN(gb));
+ } else {
+ writel(falling & ~(1 << gn), gpio->base + GPIOFEN(gb));
+ }
+}
+
+static struct irq_chip bcm2708_irqchip = {
+ .name = "GPIO",
+ .irq_enable = bcm2708_gpio_irq_unmask,
+ .irq_disable = bcm2708_gpio_irq_mask,
+ .irq_unmask = bcm2708_gpio_irq_unmask,
+ .irq_mask = bcm2708_gpio_irq_mask,
+ .irq_set_type = bcm2708_gpio_irq_set_type,
+};
+
+static irqreturn_t bcm2708_gpio_interrupt(int irq, void *dev_id)
+{
+ unsigned long edsr;
+ unsigned bank;
+ int i;
+ unsigned gpio;
+ for (bank = 0; bank <= 1; bank++) {
+ edsr = readl(__io_address(GPIO_BASE) + GPIOEDS(bank));
+ for_each_set_bit(i, &edsr, 32) {
+ gpio = i + bank * 32;
+ generic_handle_irq(gpio_to_irq(gpio));
+ }
+ writel(0xffffffff, __io_address(GPIO_BASE) + GPIOEDS(bank));
+ }
+ return IRQ_HANDLED;
+}
+
+static struct irqaction bcm2708_gpio_irq = {
+ .name = "BCM2708 GPIO catchall handler",
+ .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+ .handler = bcm2708_gpio_interrupt,
+};
+
+static void bcm2708_gpio_irq_init(struct bcm2708_gpio *ucb)
+{
+ unsigned irq;
+
+ ucb->gc.to_irq = bcm2708_gpio_to_irq;
+
+ for (irq = GPIO_IRQ_START; irq < (GPIO_IRQ_START + GPIO_IRQS); irq++) {
+ irq_set_chip_data(irq, ucb);
+ irq_set_chip(irq, &bcm2708_irqchip);
+ set_irq_flags(irq, IRQF_VALID);
+ }
+ setup_irq(IRQ_GPIO3, &bcm2708_gpio_irq);
+}
+
+#else
+
+static void bcm2708_gpio_irq_init(struct bcm2708_gpio *ucb)
+{
+}
+
+#endif /* #if BCM_GPIO_USE_IRQ ***************************************************************************************************************** */
+
+static int bcm2708_gpio_probe(struct platform_device *dev)
+{
+ struct bcm2708_gpio *ucb;
+ struct resource *res;
+ int err = 0;
+
+ printk(KERN_INFO DRIVER_NAME ": bcm2708_gpio_probe %p\n", dev);
+
+ ucb = kzalloc(sizeof(*ucb), GFP_KERNEL);
+ if (NULL == ucb) {
+ printk(KERN_ERR DRIVER_NAME ": failed to allocate "
+ "mailbox memory\n");
+ err = -ENOMEM;
+ goto err;
+ }
+
+ res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+
+ platform_set_drvdata(dev, ucb);
+ ucb->base = __io_address(GPIO_BASE);
+
+ ucb->gc.label = "bcm2708_gpio";
+ ucb->gc.base = 0;
+ ucb->gc.ngpio = ARCH_NR_GPIOS;
+ ucb->gc.owner = THIS_MODULE;
+
+ ucb->gc.direction_input = bcm2708_gpio_dir_in;
+ ucb->gc.direction_output = bcm2708_gpio_dir_out;
+ ucb->gc.get = bcm2708_gpio_get;
+ ucb->gc.set = bcm2708_gpio_set;
+ ucb->gc.can_sleep = 0;
+
+ bcm2708_gpio_irq_init(ucb);
+
+ err = gpiochip_add(&ucb->gc);
+ if (err)
+ goto err;
+
+err:
+ return err;
+
+}
+
+static int bcm2708_gpio_remove(struct platform_device *dev)
+{
+ int err = 0;
+ struct bcm2708_gpio *ucb = platform_get_drvdata(dev);
+
+ printk(KERN_ERR DRIVER_NAME ": bcm2708_gpio_remove %p\n", dev);
+
+ err = gpiochip_remove(&ucb->gc);
+
+ platform_set_drvdata(dev, NULL);
+ kfree(ucb);
+
+ return err;
+}
+
+static struct platform_driver bcm2708_gpio_driver = {
+ .probe = bcm2708_gpio_probe,
+ .remove = bcm2708_gpio_remove,
+ .driver = {
+ .name = "bcm2708_gpio"},
+};
+
+static int __init bcm2708_gpio_init(void)
+{
+ return platform_driver_register(&bcm2708_gpio_driver);
+}
+
+static void __exit bcm2708_gpio_exit(void)
+{
+ platform_driver_unregister(&bcm2708_gpio_driver);
+}
+
+module_init(bcm2708_gpio_init);
+module_exit(bcm2708_gpio_exit);
+
+MODULE_DESCRIPTION("Broadcom BCM2708 GPIO driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+++ b/arch/arm/mach-bcm2708/bcm2708.h
@@ -0,0 +1,51 @@
+/*
+ * linux/arch/arm/mach-bcm2708/bcm2708.h
+ *
+ * BCM2708 machine support header
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __BCM2708_BCM2708_H
+#define __BCM2708_BCM2708_H
+
+#include <linux/amba/bus.h>
+
+extern void __init bcm2708_init(void);
+extern void __init bcm2708_init_irq(void);
+extern void __init bcm2708_map_io(void);
+extern struct sys_timer bcm2708_timer;
+extern unsigned int mmc_status(struct device *dev);
+
+#define AMBA_DEVICE(name, busid, base, plat) \
+static struct amba_device name##_device = { \
+ .dev = { \
+ .coherent_dma_mask = ~0, \
+ .init_name = busid, \
+ .platform_data = plat, \
+ }, \
+ .res = { \
+ .start = base##_BASE, \
+ .end = (base##_BASE) + SZ_4K - 1,\
+ .flags = IORESOURCE_MEM, \
+ }, \
+ .dma_mask = ~0, \
+ .irq = base##_IRQ, \
+ /* .dma = base##_DMA,*/ \
+}
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/clock.c
@@ -0,0 +1,61 @@
+/*
+ * linux/arch/arm/mach-bcm2708/clock.c
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/string.h>
+#include <linux/clk.h>
+#include <linux/mutex.h>
+
+#include <asm/clkdev.h>
+
+#include "clock.h"
+
+int clk_enable(struct clk *clk)
+{
+ return 0;
+}
+EXPORT_SYMBOL(clk_enable);
+
+void clk_disable(struct clk *clk)
+{
+}
+EXPORT_SYMBOL(clk_disable);
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+ return clk->rate;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ return clk->rate;
+}
+EXPORT_SYMBOL(clk_round_rate);
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ return -EIO;
+}
+EXPORT_SYMBOL(clk_set_rate);
--- /dev/null
+++ b/arch/arm/mach-bcm2708/clock.h
@@ -0,0 +1,24 @@
+/*
+ * linux/arch/arm/mach-bcm2708/clock.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+struct module;
+
+struct clk {
+ unsigned long rate;
+};
--- /dev/null
+++ b/arch/arm/mach-bcm2708/dma.c
@@ -0,0 +1,399 @@
+/*
+ * linux/arch/arm/mach-bcm2708/dma.c
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/scatterlist.h>
+
+#include <mach/dma.h>
+#include <mach/irqs.h>
+
+/*****************************************************************************\
+ * *
+ * Configuration *
+ * *
+\*****************************************************************************/
+
+#define CACHE_LINE_MASK 31
+#define DRIVER_NAME BCM_DMAMAN_DRIVER_NAME
+#define DEFAULT_DMACHAN_BITMAP 0x10 /* channel 4 only */
+
+/* valid only for channels 0 - 14, 15 has its own base address */
+#define BCM2708_DMA_CHAN(n) ((n)<<8) /* base address */
+#define BCM2708_DMA_CHANIO(dma_base, n) \
+ ((void __iomem *)((char *)(dma_base)+BCM2708_DMA_CHAN(n)))
+
+
+/*****************************************************************************\
+ * *
+ * DMA Auxilliary Functions *
+ * *
+\*****************************************************************************/
+
+/* A DMA buffer on an arbitrary boundary may separate a cache line into a
+ section inside the DMA buffer and another section outside it.
+ Even if we flush DMA buffers from the cache there is always the chance that
+ during a DMA someone will access the part of a cache line that is outside
+ the DMA buffer - which will then bring in unwelcome data.
+ Without being able to dictate our own buffer pools we must insist that
+ DMA buffers consist of a whole number of cache lines.
+*/
+
+extern int
+bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len)
+{
+ int i;
+
+ for (i = 0; i < sg_len; i++) {
+ if (sg_ptr[i].offset & CACHE_LINE_MASK ||
+ sg_ptr[i].length & CACHE_LINE_MASK)
+ return 0;
+ }
+
+ return 1;
+}
+EXPORT_SYMBOL_GPL(bcm_sg_suitable_for_dma);
+
+extern void
+bcm_dma_start(void __iomem *dma_chan_base, dma_addr_t control_block)
+{
+ dsb(); /* ARM data synchronization (push) operation */
+
+ writel(control_block, dma_chan_base + BCM2708_DMA_ADDR);
+ writel(BCM2708_DMA_ACTIVE, dma_chan_base + BCM2708_DMA_CS);
+}
+
+extern void bcm_dma_wait_idle(void __iomem *dma_chan_base)
+{
+ dsb();
+
+ /* ugly busy wait only option for now */
+ while (readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_ACTIVE)
+ cpu_relax();
+}
+
+EXPORT_SYMBOL_GPL(bcm_dma_start);
+
+/* Complete an ongoing DMA (assuming its results are to be ignored)
+ Does nothing if there is no DMA in progress.
+ This routine waits for the current AXI transfer to complete before
+ terminating the current DMA. If the current transfer is hung on a DREQ used
+ by an uncooperative peripheral the AXI transfer may never complete. In this
+ case the routine times out and return a non-zero error code.
+ Use of this routine doesn't guarantee that the ongoing or aborted DMA
+ does not produce an interrupt.
+*/
+extern int
+bcm_dma_abort(void __iomem *dma_chan_base)
+{
+ unsigned long int cs;
+ int rc = 0;
+
+ cs = readl(dma_chan_base + BCM2708_DMA_CS);
+
+ if (BCM2708_DMA_ACTIVE & cs) {
+ long int timeout = 10000;
+
+ /* write 0 to the active bit - pause the DMA */
+ writel(0, dma_chan_base + BCM2708_DMA_CS);
+
+ /* wait for any current AXI transfer to complete */
+ while (0 != (cs & BCM2708_DMA_ISPAUSED) && --timeout >= 0)
+ cs = readl(dma_chan_base + BCM2708_DMA_CS);
+
+ if (0 != (cs & BCM2708_DMA_ISPAUSED)) {
+ /* we'll un-pause when we set of our next DMA */
+ rc = -ETIMEDOUT;
+
+ } else if (BCM2708_DMA_ACTIVE & cs) {
+ /* terminate the control block chain */
+ writel(0, dma_chan_base + BCM2708_DMA_NEXTCB);
+
+ /* abort the whole DMA */
+ writel(BCM2708_DMA_ABORT | BCM2708_DMA_ACTIVE,
+ dma_chan_base + BCM2708_DMA_CS);
+ }
+ }
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(bcm_dma_abort);
+
+
+/***************************************************************************** \
+ * *
+ * DMA Manager Device Methods *
+ * *
+\*****************************************************************************/
+
+struct vc_dmaman {
+ void __iomem *dma_base;
+ u32 chan_available; /* bitmap of available channels */
+ u32 has_feature[BCM_DMA_FEATURE_COUNT]; /* bitmap of feature presence */
+};
+
+static void vc_dmaman_init(struct vc_dmaman *dmaman, void __iomem *dma_base,
+ u32 chans_available)
+{
+ dmaman->dma_base = dma_base;
+ dmaman->chan_available = chans_available;
+ dmaman->has_feature[BCM_DMA_FEATURE_FAST_ORD] = 0x0c; /* chans 2 & 3 */
+ dmaman->has_feature[BCM_DMA_FEATURE_BULK_ORD] = 0x01; /* chan 0 */
+}
+
+static int vc_dmaman_chan_alloc(struct vc_dmaman *dmaman,
+ unsigned preferred_feature_set)
+{
+ u32 chans;
+ int feature;
+
+ chans = dmaman->chan_available;
+ for (feature = 0; feature < BCM_DMA_FEATURE_COUNT; feature++)
+ /* select the subset of available channels with the desired
+ feature so long as some of the candidate channels have that
+ feature */
+ if ((preferred_feature_set & (1 << feature)) &&
+ (chans & dmaman->has_feature[feature]))
+ chans &= dmaman->has_feature[feature];
+
+ if (chans) {
+ int chan = 0;
+ /* return the ordinal of the first channel in the bitmap */
+ while (chans != 0 && (chans & 1) == 0) {
+ chans >>= 1;
+ chan++;
+ }
+ /* claim the channel */
+ dmaman->chan_available &= ~(1 << chan);
+ return chan;
+ } else
+ return -ENOMEM;
+}
+
+static int vc_dmaman_chan_free(struct vc_dmaman *dmaman, int chan)
+{
+ if (chan < 0)
+ return -EINVAL;
+ else if ((1 << chan) & dmaman->chan_available)
+ return -EIDRM;
+ else {
+ dmaman->chan_available |= (1 << chan);
+ return 0;
+ }
+}
+
+/*****************************************************************************\
+ * *
+ * DMA IRQs *
+ * *
+\*****************************************************************************/
+
+static unsigned char bcm_dma_irqs[] = {
+ IRQ_DMA0,
+ IRQ_DMA1,
+ IRQ_DMA2,
+ IRQ_DMA3,
+ IRQ_DMA4,
+ IRQ_DMA5,
+ IRQ_DMA6,
+ IRQ_DMA7,
+ IRQ_DMA8,
+ IRQ_DMA9,
+ IRQ_DMA10,
+ IRQ_DMA11,
+ IRQ_DMA12
+};
+
+
+/***************************************************************************** \
+ * *
+ * DMA Manager Monitor *
+ * *
+\*****************************************************************************/
+
+static struct device *dmaman_dev; /* we assume there's only one! */
+
+extern int bcm_dma_chan_alloc(unsigned preferred_feature_set,
+ void __iomem **out_dma_base, int *out_dma_irq)
+{
+ if (!dmaman_dev)
+ return -ENODEV;
+ else {
+ struct vc_dmaman *dmaman = dev_get_drvdata(dmaman_dev);
+ int rc;
+
+ device_lock(dmaman_dev);
+ rc = vc_dmaman_chan_alloc(dmaman, preferred_feature_set);
+ if (rc >= 0) {
+ *out_dma_base = BCM2708_DMA_CHANIO(dmaman->dma_base,
+ rc);
+ *out_dma_irq = bcm_dma_irqs[rc];
+ }
+ device_unlock(dmaman_dev);
+
+ return rc;
+ }
+}
+EXPORT_SYMBOL_GPL(bcm_dma_chan_alloc);
+
+extern int bcm_dma_chan_free(int channel)
+{
+ if (dmaman_dev) {
+ struct vc_dmaman *dmaman = dev_get_drvdata(dmaman_dev);
+ int rc;
+
+ device_lock(dmaman_dev);
+ rc = vc_dmaman_chan_free(dmaman, channel);
+ device_unlock(dmaman_dev);
+
+ return rc;
+ } else
+ return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(bcm_dma_chan_free);
+
+static int dev_dmaman_register(const char *dev_name, struct device *dev)
+{
+ int rc = dmaman_dev ? -EINVAL : 0;
+ dmaman_dev = dev;
+ return rc;
+}
+
+static void dev_dmaman_deregister(const char *dev_name, struct device *dev)
+{
+ dmaman_dev = NULL;
+}
+
+/*****************************************************************************\
+ * *
+ * DMA Device *
+ * *
+\*****************************************************************************/
+
+static int dmachans = -1; /* module parameter */
+
+static int bcm_dmaman_probe(struct platform_device *pdev)
+{
+ int ret = 0;
+ struct vc_dmaman *dmaman;
+ struct resource *dma_res = NULL;
+ void __iomem *dma_base = NULL;
+ int have_dma_region = 0;
+
+ dmaman = kzalloc(sizeof(*dmaman), GFP_KERNEL);
+ if (NULL == dmaman) {
+ printk(KERN_ERR DRIVER_NAME ": failed to allocate "
+ "DMA management memory\n");
+ ret = -ENOMEM;
+ } else {
+
+ dma_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (dma_res == NULL) {
+ printk(KERN_ERR DRIVER_NAME ": failed to obtain memory "
+ "resource\n");
+ ret = -ENODEV;
+ } else if (!request_mem_region(dma_res->start,
+ resource_size(dma_res),
+ DRIVER_NAME)) {
+ dev_err(&pdev->dev, "cannot obtain DMA region\n");
+ ret = -EBUSY;
+ } else {
+ have_dma_region = 1;
+ dma_base = ioremap(dma_res->start,
+ resource_size(dma_res));
+ if (!dma_base) {
+ dev_err(&pdev->dev, "cannot map DMA region\n");
+ ret = -ENOMEM;
+ } else {
+ /* use module parameter if one was provided */
+ if (dmachans > 0)
+ vc_dmaman_init(dmaman, dma_base,
+ dmachans);
+ else
+ vc_dmaman_init(dmaman, dma_base,
+ DEFAULT_DMACHAN_BITMAP);
+
+ platform_set_drvdata(pdev, dmaman);
+ dev_dmaman_register(DRIVER_NAME, &pdev->dev);
+
+ printk(KERN_INFO DRIVER_NAME ": DMA manager "
+ "at %p\n", dma_base);
+ }
+ }
+ }
+ if (ret != 0) {
+ if (dma_base)
+ iounmap(dma_base);
+ if (dma_res && have_dma_region)
+ release_mem_region(dma_res->start,
+ resource_size(dma_res));
+ if (dmaman)
+ kfree(dmaman);
+ }
+ return ret;
+}
+
+static int bcm_dmaman_remove(struct platform_device *pdev)
+{
+ struct vc_dmaman *dmaman = platform_get_drvdata(pdev);
+
+ platform_set_drvdata(pdev, NULL);
+ dev_dmaman_deregister(DRIVER_NAME, &pdev->dev);
+ kfree(dmaman);
+
+ return 0;
+}
+
+static struct platform_driver bcm_dmaman_driver = {
+ .probe = bcm_dmaman_probe,
+ .remove = bcm_dmaman_remove,
+
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+/*****************************************************************************\
+ * *
+ * Driver init/exit *
+ * *
+\*****************************************************************************/
+
+static int __init bcm_dmaman_drv_init(void)
+{
+ int ret;
+
+ ret = platform_driver_register(&bcm_dmaman_driver);
+ if (ret != 0) {
+ printk(KERN_ERR DRIVER_NAME ": failed to register "
+ "on platform\n");
+ }
+
+ return ret;
+}
+
+static void __exit bcm_dmaman_drv_exit(void)
+{
+ platform_driver_unregister(&bcm_dmaman_driver);
+}
+
+module_init(bcm_dmaman_drv_init);
+module_exit(bcm_dmaman_drv_exit);
+
+module_param(dmachans, int, 0644);
+
+MODULE_AUTHOR("Gray Girling <grayg@broadcom.com>");
+MODULE_DESCRIPTION("DMA channel manager driver");
+MODULE_LICENSE("GPL");
+
+MODULE_PARM_DESC(dmachans, "Bitmap of DMA channels available to the ARM");
--- /dev/null
+++ b/arch/arm/mach-bcm2708/dmaer.c
@@ -0,0 +1,887 @@
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kdev_t.h>
+#include <linux/fs.h>
+#include <linux/cdev.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/pagemap.h>
+#include <linux/device.h>
+#include <linux/jiffies.h>
+#include <linux/timex.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/uaccess.h>
+#include <asm/atomic.h>
+#include <asm/cacheflush.h>
+#include <asm/io.h>
+
+#include <mach/dma.h>
+#include <mach/vc_support.h>
+
+#ifdef ECLIPSE_IGNORE
+
+#define __user
+#define __init
+#define __exit
+#define __iomem
+#define KERN_DEBUG
+#define KERN_ERR
+#define KERN_WARNING
+#define KERN_INFO
+#define _IOWR(a, b, c) b
+#define _IOW(a, b, c) b
+#define _IO(a, b) b
+
+#endif
+
+//#define inline
+
+#define PRINTK(args...) printk(args)
+//#define PRINTK_VERBOSE(args...) printk(args)
+//#define PRINTK(args...)
+#define PRINTK_VERBOSE(args...)
+
+/***** TYPES ****/
+#define PAGES_PER_LIST 500
+struct PageList
+{
+ struct page *m_pPages[PAGES_PER_LIST];
+ unsigned int m_used;
+ struct PageList *m_pNext;
+};
+
+struct VmaPageList
+{
+ //each vma has a linked list of pages associated with it
+ struct PageList *m_pPageHead;
+ struct PageList *m_pPageTail;
+ unsigned int m_refCount;
+};
+
+struct DmaControlBlock
+{
+ unsigned int m_transferInfo;
+ void __user *m_pSourceAddr;
+ void __user *m_pDestAddr;
+ unsigned int m_xferLen;
+ unsigned int m_tdStride;
+ struct DmaControlBlock *m_pNext;
+ unsigned int m_blank1, m_blank2;
+};
+
+/***** DEFINES ******/
+//magic number defining the module
+#define DMA_MAGIC 0xdd
+
+//do user virtual to physical translation of the CB chain
+#define DMA_PREPARE _IOWR(DMA_MAGIC, 0, struct DmaControlBlock *)
+
+//kick the pre-prepared CB chain
+#define DMA_KICK _IOW(DMA_MAGIC, 1, struct DmaControlBlock *)
+
+//prepare it, kick it, wait for it
+#define DMA_PREPARE_KICK_WAIT _IOWR(DMA_MAGIC, 2, struct DmaControlBlock *)
+
+//prepare it, kick it, don't wait for it
+#define DMA_PREPARE_KICK _IOWR(DMA_MAGIC, 3, struct DmaControlBlock *)
+
+//not currently implemented
+#define DMA_WAIT_ONE _IO(DMA_MAGIC, 4, struct DmaControlBlock *)
+
+//wait on all kicked CB chains
+#define DMA_WAIT_ALL _IO(DMA_MAGIC, 5)
+
+//in order to discover the largest AXI burst that should be programmed into the transfer params
+#define DMA_MAX_BURST _IO(DMA_MAGIC, 6)
+
+//set the address range through which the user address is assumed to already by a physical address
+#define DMA_SET_MIN_PHYS _IOW(DMA_MAGIC, 7, unsigned long)
+#define DMA_SET_MAX_PHYS _IOW(DMA_MAGIC, 8, unsigned long)
+#define DMA_SET_PHYS_OFFSET _IOW(DMA_MAGIC, 9, unsigned long)
+
+//used to define the size for the CMA-based allocation *in pages*, can only be done once once the file is opened
+#define DMA_CMA_SET_SIZE _IOW(DMA_MAGIC, 10, unsigned long)
+
+//used to get the version of the module, to test for a capability
+#define DMA_GET_VERSION _IO(DMA_MAGIC, 99)
+
+#define VERSION_NUMBER 1
+
+#define VIRT_TO_BUS_CACHE_SIZE 8
+
+/***** FILE OPS *****/
+static int Open(struct inode *pInode, struct file *pFile);
+static int Release(struct inode *pInode, struct file *pFile);
+static long Ioctl(struct file *pFile, unsigned int cmd, unsigned long arg);
+static ssize_t Read(struct file *pFile, char __user *pUser, size_t count, loff_t *offp);
+static int Mmap(struct file *pFile, struct vm_area_struct *pVma);
+
+/***** VMA OPS ****/
+static void VmaOpen4k(struct vm_area_struct *pVma);
+static void VmaClose4k(struct vm_area_struct *pVma);
+static int VmaFault4k(struct vm_area_struct *pVma, struct vm_fault *pVmf);
+
+/**** DMA PROTOTYPES */
+static struct DmaControlBlock __user *DmaPrepare(struct DmaControlBlock __user *pUserCB, int *pError);
+static int DmaKick(struct DmaControlBlock __user *pUserCB);
+static void DmaWaitAll(void);
+
+/**** GENERIC ****/
+static int __init dmaer_init(void);
+static void __exit dmaer_exit(void);
+
+/*** OPS ***/
+static struct vm_operations_struct g_vmOps4k = {
+ .open = VmaOpen4k,
+ .close = VmaClose4k,
+ .fault = VmaFault4k,
+};
+
+static struct file_operations g_fOps = {
+ .owner = THIS_MODULE,
+ .llseek = 0,
+ .read = Read,
+ .write = 0,
+ .unlocked_ioctl = Ioctl,
+ .open = Open,
+ .release = Release,
+ .mmap = Mmap,
+};
+
+/***** GLOBALS ******/
+static dev_t g_majorMinor;
+
+//tracking usage of the two files
+static atomic_t g_oneLock4k = ATOMIC_INIT(1);
+
+//device operations
+static struct cdev g_cDev;
+static int g_trackedPages = 0;
+
+//dma control
+static unsigned int *g_pDmaChanBase;
+static int g_dmaIrq;
+static int g_dmaChan;
+
+//cma allocation
+static int g_cmaHandle;
+
+//user virtual to bus address translation acceleration
+static unsigned long g_virtAddr[VIRT_TO_BUS_CACHE_SIZE];
+static unsigned long g_busAddr[VIRT_TO_BUS_CACHE_SIZE];
+static unsigned long g_cbVirtAddr;
+static unsigned long g_cbBusAddr;
+static int g_cacheInsertAt;
+static int g_cacheHit, g_cacheMiss;
+
+//off by default
+static void __user *g_pMinPhys;
+static void __user *g_pMaxPhys;
+static unsigned long g_physOffset;
+
+/****** CACHE OPERATIONS ********/
+static inline void FlushAddrCache(void)
+{
+ int count = 0;
+ for (count = 0; count < VIRT_TO_BUS_CACHE_SIZE; count++)
+ g_virtAddr[count] = 0xffffffff; //never going to match as we always chop the bottom bits anyway
+
+ g_cbVirtAddr = 0xffffffff;
+
+ g_cacheInsertAt = 0;
+}
+
+//translate from a user virtual address to a bus address by mapping the page
+//NB this won't lock a page in memory, so to avoid potential paging issues using kernel logical addresses
+static inline void __iomem *UserVirtualToBus(void __user *pUser)
+{
+ int mapped;
+ struct page *pPage;
+ void *phys;
+
+ //map it (requiring that the pointer points to something that does not hang off the page boundary)
+ mapped = get_user_pages(current, current->mm,
+ (unsigned long)pUser, 1,
+ 1, 0,
+ &pPage,
+ 0);
+
+ if (mapped <= 0) //error
+ return 0;
+
+ PRINTK_VERBOSE(KERN_DEBUG "user virtual %p arm phys %p bus %p\n",
+ pUser, page_address(pPage), (void __iomem *)__virt_to_bus(page_address(pPage)));
+
+ //get the arm physical address
+ phys = page_address(pPage) + offset_in_page(pUser);
+ page_cache_release(pPage);
+
+ //and now the bus address
+ return (void __iomem *)__virt_to_bus(phys);
+}
+
+static inline void __iomem *UserVirtualToBusViaCbCache(void __user *pUser)
+{
+ unsigned long virtual_page = (unsigned long)pUser & ~4095;
+ unsigned long page_offset = (unsigned long)pUser & 4095;
+ unsigned long bus_addr;
+
+ if (g_cbVirtAddr == virtual_page)
+ {
+ bus_addr = g_cbBusAddr + page_offset;
+ g_cacheHit++;
+ return (void __iomem *)bus_addr;
+ }
+ else
+ {
+ bus_addr = (unsigned long)UserVirtualToBus(pUser);
+
+ if (!bus_addr)
+ return 0;
+
+ g_cbVirtAddr = virtual_page;
+ g_cbBusAddr = bus_addr & ~4095;
+ g_cacheMiss++;
+
+ return (void __iomem *)bus_addr;
+ }
+}
+
+//do the same as above, by query our virt->bus cache
+static inline void __iomem *UserVirtualToBusViaCache(void __user *pUser)
+{
+ int count;
+ //get the page and its offset
+ unsigned long virtual_page = (unsigned long)pUser & ~4095;
+ unsigned long page_offset = (unsigned long)pUser & 4095;
+ unsigned long bus_addr;
+
+ if (pUser >= g_pMinPhys && pUser < g_pMaxPhys)
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "user->phys passthrough on %p\n", pUser);
+ return (void __iomem *)((unsigned long)pUser + g_physOffset);
+ }
+
+ //check the cache for our entry
+ for (count = 0; count < VIRT_TO_BUS_CACHE_SIZE; count++)
+ if (g_virtAddr[count] == virtual_page)
+ {
+ bus_addr = g_busAddr[count] + page_offset;
+ g_cacheHit++;
+ return (void __iomem *)bus_addr;
+ }
+
+ //not found, look up manually and then insert its page address
+ bus_addr = (unsigned long)UserVirtualToBus(pUser);
+
+ if (!bus_addr)
+ return 0;
+
+ g_virtAddr[g_cacheInsertAt] = virtual_page;
+ g_busAddr[g_cacheInsertAt] = bus_addr & ~4095;
+
+ //round robin
+ g_cacheInsertAt++;
+ if (g_cacheInsertAt == VIRT_TO_BUS_CACHE_SIZE)
+ g_cacheInsertAt = 0;
+
+ g_cacheMiss++;
+
+ return (void __iomem *)bus_addr;
+}
+
+/***** FILE OPERATIONS ****/
+static int Open(struct inode *pInode, struct file *pFile)
+{
+ PRINTK(KERN_DEBUG "file opening: %d/%d\n", imajor(pInode), iminor(pInode));
+
+ //check which device we are
+ if (iminor(pInode) == 0) //4k
+ {
+ //only one at a time
+ if (!atomic_dec_and_test(&g_oneLock4k))
+ {
+ atomic_inc(&g_oneLock4k);
+ return -EBUSY;
+ }
+ }
+ else
+ return -EINVAL;
+
+ //todo there will be trouble if two different processes open the files
+
+ //reset after any file is opened
+ g_pMinPhys = (void __user *)-1;
+ g_pMaxPhys = (void __user *)0;
+ g_physOffset = 0;
+ g_cmaHandle = 0;
+
+ return 0;
+}
+
+static int Release(struct inode *pInode, struct file *pFile)
+{
+ PRINTK(KERN_DEBUG "file closing, %d pages tracked\n", g_trackedPages);
+ if (g_trackedPages)
+ PRINTK(KERN_ERR "we\'re leaking memory!\n");
+
+ //wait for any dmas to finish
+ DmaWaitAll();
+
+ //free this memory on the application closing the file or it crashing (implicitly closing the file)
+ if (g_cmaHandle)
+ {
+ PRINTK(KERN_DEBUG "unlocking vc memory\n");
+ if (UnlockVcMemory(g_cmaHandle))
+ PRINTK(KERN_ERR "uh-oh, unable to unlock vc memory!\n");
+ PRINTK(KERN_DEBUG "releasing vc memory\n");
+ if (ReleaseVcMemory(g_cmaHandle))
+ PRINTK(KERN_ERR "uh-oh, unable to release vc memory!\n");
+ }
+
+ if (iminor(pInode) == 0)
+ atomic_inc(&g_oneLock4k);
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
+static struct DmaControlBlock __user *DmaPrepare(struct DmaControlBlock __user *pUserCB, int *pError)
+{
+ struct DmaControlBlock kernCB;
+ struct DmaControlBlock __user *pUNext;
+ void __iomem *pSourceBus, __iomem *pDestBus;
+
+ //get the control block into kernel memory so we can work on it
+ if (copy_from_user(&kernCB, pUserCB, sizeof(struct DmaControlBlock)) != 0)
+ {
+ PRINTK(KERN_ERR "copy_from_user failed for user cb %p\n", pUserCB);
+ *pError = 1;
+ return 0;
+ }
+
+ if (kernCB.m_pSourceAddr == 0 || kernCB.m_pDestAddr == 0)
+ {
+ PRINTK(KERN_ERR "faulty source (%p) dest (%p) addresses for user cb %p\n",
+ kernCB.m_pSourceAddr, kernCB.m_pDestAddr, pUserCB);
+ *pError = 1;
+ return 0;
+ }
+
+ pSourceBus = UserVirtualToBusViaCache(kernCB.m_pSourceAddr);
+ pDestBus = UserVirtualToBusViaCache(kernCB.m_pDestAddr);
+
+ if (!pSourceBus || !pDestBus)
+ {
+ PRINTK(KERN_ERR "virtual to bus translation failure for source/dest %p/%p->%p/%p\n",
+ kernCB.m_pSourceAddr, kernCB.m_pDestAddr,
+ pSourceBus, pDestBus);
+ *pError = 1;
+ return 0;
+ }
+
+ //update the user structure with the new bus addresses
+ kernCB.m_pSourceAddr = pSourceBus;
+ kernCB.m_pDestAddr = pDestBus;
+
+ PRINTK_VERBOSE(KERN_DEBUG "final source %p dest %p\n", kernCB.m_pSourceAddr, kernCB.m_pDestAddr);
+
+ //sort out the bus address for the next block
+ pUNext = kernCB.m_pNext;
+
+ if (kernCB.m_pNext)
+ {
+ void __iomem *pNextBus;
+ pNextBus = UserVirtualToBusViaCbCache(kernCB.m_pNext);
+
+ if (!pNextBus)
+ {
+ PRINTK(KERN_ERR "virtual to bus translation failure for m_pNext\n");
+ *pError = 1;
+ return 0;
+ }
+
+ //update the pointer with the bus address
+ kernCB.m_pNext = pNextBus;
+ }
+
+ //write it back to user space
+ if (copy_to_user(pUserCB, &kernCB, sizeof(struct DmaControlBlock)) != 0)
+ {
+ PRINTK(KERN_ERR "copy_to_user failed for cb %p\n", pUserCB);
+ *pError = 1;
+ return 0;
+ }
+
+ __cpuc_flush_dcache_area(pUserCB, 32);
+
+ *pError = 0;
+ return pUNext;
+}
+
+static int DmaKick(struct DmaControlBlock __user *pUserCB)
+{
+ void __iomem *pBusCB;
+
+ pBusCB = UserVirtualToBusViaCbCache(pUserCB);
+ if (!pBusCB)
+ {
+ PRINTK(KERN_ERR "virtual to bus translation failure for cb\n");
+ return 1;
+ }
+
+ //flush_cache_all();
+
+ bcm_dma_start(g_pDmaChanBase, (dma_addr_t)pBusCB);
+
+ return 0;
+}
+
+static void DmaWaitAll(void)
+{
+ int counter = 0;
+ volatile int inner_count;
+ volatile unsigned int cs;
+ unsigned long time_before, time_after;
+
+ time_before = jiffies;
+ //bcm_dma_wait_idle(g_pDmaChanBase);
+ dsb();
+
+ cs = readl(g_pDmaChanBase);
+
+ while ((cs & 1) == 1)
+ {
+ cs = readl(g_pDmaChanBase);
+ counter++;
+
+ for (inner_count = 0; inner_count < 32; inner_count++);
+
+ asm volatile ("MCR p15,0,r0,c7,c0,4 \n");
+ //cpu_do_idle();
+ if (counter >= 1000000)
+ {
+ PRINTK(KERN_WARNING "DMA failed to finish in a timely fashion\n");
+ break;
+ }
+ }
+ time_after = jiffies;
+ PRINTK_VERBOSE(KERN_DEBUG "done, counter %d, cs %08x", counter, cs);
+ PRINTK_VERBOSE(KERN_DEBUG "took %ld jiffies, %d HZ\n", time_after - time_before, HZ);
+}
+
+static long Ioctl(struct file *pFile, unsigned int cmd, unsigned long arg)
+{
+ int error = 0;
+ PRINTK_VERBOSE(KERN_DEBUG "ioctl cmd %x arg %lx\n", cmd, arg);
+
+ switch (cmd)
+ {
+ case DMA_PREPARE:
+ case DMA_PREPARE_KICK:
+ case DMA_PREPARE_KICK_WAIT:
+ {
+ struct DmaControlBlock __user *pUCB = (struct DmaControlBlock *)arg;
+ int steps = 0;
+ unsigned long start_time = jiffies;
+ (void)start_time;
+
+ //flush our address cache
+ FlushAddrCache();
+
+ PRINTK_VERBOSE(KERN_DEBUG "dma prepare\n");
+
+ //do virtual to bus translation for each entry
+ do
+ {
+ pUCB = DmaPrepare(pUCB, &error);
+ } while (error == 0 && ++steps && pUCB);
+ PRINTK_VERBOSE(KERN_DEBUG "prepare done in %d steps, %ld\n", steps, jiffies - start_time);
+
+ //carry straight on if we want to kick too
+ if (cmd == DMA_PREPARE || error)
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "falling out\n");
+ return error ? -EINVAL : 0;
+ }
+ }
+ case DMA_KICK:
+ PRINTK_VERBOSE(KERN_DEBUG "dma begin\n");
+
+ if (cmd == DMA_KICK)
+ FlushAddrCache();
+
+ DmaKick((struct DmaControlBlock __user *)arg);
+
+ if (cmd != DMA_PREPARE_KICK_WAIT)
+ break;
+/* case DMA_WAIT_ONE:
+ //PRINTK(KERN_DEBUG "dma wait one\n");
+ break;*/
+ case DMA_WAIT_ALL:
+ //PRINTK(KERN_DEBUG "dma wait all\n");
+ DmaWaitAll();
+ break;
+ case DMA_MAX_BURST:
+ if (g_dmaChan == 0)
+ return 10;
+ else
+ return 5;
+ case DMA_SET_MIN_PHYS:
+ g_pMinPhys = (void __user *)arg;
+ PRINTK(KERN_DEBUG "min/max user/phys bypass set to %p %p\n", g_pMinPhys, g_pMaxPhys);
+ break;
+ case DMA_SET_MAX_PHYS:
+ g_pMaxPhys = (void __user *)arg;
+ PRINTK(KERN_DEBUG "min/max user/phys bypass set to %p %p\n", g_pMinPhys, g_pMaxPhys);
+ break;
+ case DMA_SET_PHYS_OFFSET:
+ g_physOffset = arg;
+ PRINTK(KERN_DEBUG "user/phys bypass offset set to %ld\n", g_physOffset);
+ break;
+ case DMA_CMA_SET_SIZE:
+ {
+ unsigned int pBusAddr;
+
+ if (g_cmaHandle)
+ {
+ PRINTK(KERN_ERR "memory has already been allocated (handle %d)\n", g_cmaHandle);
+ return -EINVAL;
+ }
+
+ PRINTK(KERN_INFO "allocating %ld bytes of VC memory\n", arg * 4096);
+
+ //get the memory
+ if (AllocateVcMemory(&g_cmaHandle, arg * 4096, 4096, MEM_FLAG_L1_NONALLOCATING | MEM_FLAG_NO_INIT | MEM_FLAG_HINT_PERMALOCK))
+ {
+ PRINTK(KERN_ERR "failed to allocate %ld bytes of VC memory\n", arg * 4096);
+ g_cmaHandle = 0;
+ return -EINVAL;
+ }
+
+ //get an address for it
+ PRINTK(KERN_INFO "trying to map VC memory\n");
+
+ if (LockVcMemory(&pBusAddr, g_cmaHandle))
+ {
+ PRINTK(KERN_ERR "failed to map CMA handle %d, releasing memory\n", g_cmaHandle);
+ ReleaseVcMemory(g_cmaHandle);
+ g_cmaHandle = 0;
+ }
+
+ PRINTK(KERN_INFO "bus address for CMA memory is %x\n", pBusAddr);
+ return pBusAddr;
+ }
+ case DMA_GET_VERSION:
+ PRINTK(KERN_DEBUG "returning version number, %d\n", VERSION_NUMBER);
+ return VERSION_NUMBER;
+ default:
+ PRINTK(KERN_DEBUG "unknown ioctl: %d\n", cmd);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static ssize_t Read(struct file *pFile, char __user *pUser, size_t count, loff_t *offp)
+{
+ return -EIO;
+}
+
+static int Mmap(struct file *pFile, struct vm_area_struct *pVma)
+{
+ struct PageList *pPages;
+ struct VmaPageList *pVmaList;
+
+ PRINTK_VERBOSE(KERN_DEBUG "MMAP vma %p, length %ld (%s %d)\n",
+ pVma, pVma->vm_end - pVma->vm_start,
+ current->comm, current->pid);
+ PRINTK_VERBOSE(KERN_DEBUG "MMAP %p %d (tracked %d)\n", pVma, current->pid, g_trackedPages);
+
+ //make a new page list
+ pPages = (struct PageList *)kmalloc(sizeof(struct PageList), GFP_KERNEL);
+ if (!pPages)
+ {
+ PRINTK(KERN_ERR "couldn\'t allocate a new page list (%s %d)\n",
+ current->comm, current->pid);
+ return -ENOMEM;
+ }
+
+ //clear the page list
+ pPages->m_used = 0;
+ pPages->m_pNext = 0;
+
+ //insert our vma and new page list somewhere
+ if (!pVma->vm_private_data)
+ {
+ struct VmaPageList *pList;
+
+ PRINTK_VERBOSE(KERN_DEBUG "new vma list, making new one (%s %d)\n",
+ current->comm, current->pid);
+
+ //make a new vma list
+ pList = (struct VmaPageList *)kmalloc(sizeof(struct VmaPageList), GFP_KERNEL);
+ if (!pList)
+ {
+ PRINTK(KERN_ERR "couldn\'t allocate vma page list (%s %d)\n",
+ current->comm, current->pid);
+ kfree(pPages);
+ return -ENOMEM;
+ }
+
+ //clear this list
+ pVma->vm_private_data = (void *)pList;
+ pList->m_refCount = 0;
+ }
+
+ pVmaList = (struct VmaPageList *)pVma->vm_private_data;
+
+ //add it to the vma list
+ pVmaList->m_pPageHead = pPages;
+ pVmaList->m_pPageTail = pPages;
+
+ pVma->vm_ops = &g_vmOps4k;
+ pVma->vm_flags |= VM_IO;
+
+ VmaOpen4k(pVma);
+
+ return 0;
+}
+
+/****** VMA OPERATIONS ******/
+
+static void VmaOpen4k(struct vm_area_struct *pVma)
+{
+ struct VmaPageList *pVmaList;
+
+ PRINTK_VERBOSE(KERN_DEBUG "vma open %p private %p (%s %d), %d live pages\n", pVma, pVma->vm_private_data, current->comm, current->pid, g_trackedPages);
+ PRINTK_VERBOSE(KERN_DEBUG "OPEN %p %d %ld pages (tracked pages %d)\n",
+ pVma, current->pid, (pVma->vm_end - pVma->vm_start) >> 12,
+ g_trackedPages);
+
+ pVmaList = (struct VmaPageList *)pVma->vm_private_data;
+
+ if (pVmaList)
+ {
+ pVmaList->m_refCount++;
+ PRINTK_VERBOSE(KERN_DEBUG "ref count is now %d\n", pVmaList->m_refCount);
+ }
+ else
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "err, open but no vma page list\n");
+ }
+}
+
+static void VmaClose4k(struct vm_area_struct *pVma)
+{
+ struct VmaPageList *pVmaList;
+ int freed = 0;
+
+ PRINTK_VERBOSE(KERN_DEBUG "vma close %p private %p (%s %d)\n", pVma, pVma->vm_private_data, current->comm, current->pid);
+
+ //wait for any dmas to finish
+ DmaWaitAll();
+
+ //find our vma in the list
+ pVmaList = (struct VmaPageList *)pVma->vm_private_data;
+
+ //may be a fork
+ if (pVmaList)
+ {
+ struct PageList *pPages;
+
+ pVmaList->m_refCount--;
+
+ if (pVmaList->m_refCount == 0)
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "found vma, freeing pages (%s %d)\n",
+ current->comm, current->pid);
+
+ pPages = pVmaList->m_pPageHead;
+
+ if (!pPages)
+ {
+ PRINTK(KERN_ERR "no page list (%s %d)!\n",
+ current->comm, current->pid);
+ return;
+ }
+
+ while (pPages)
+ {
+ struct PageList *next;
+ int count;
+
+ PRINTK_VERBOSE(KERN_DEBUG "page list (%s %d)\n",
+ current->comm, current->pid);
+
+ next = pPages->m_pNext;
+ for (count = 0; count < pPages->m_used; count++)
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "freeing page %p (%s %d)\n",
+ pPages->m_pPages[count],
+ current->comm, current->pid);
+ __free_pages(pPages->m_pPages[count], 0);
+ g_trackedPages--;
+ freed++;
+ }
+
+ PRINTK_VERBOSE(KERN_DEBUG "freeing page list (%s %d)\n",
+ current->comm, current->pid);
+ kfree(pPages);
+ pPages = next;
+ }
+
+ //remove our vma from the list
+ kfree(pVmaList);
+ pVma->vm_private_data = 0;
+ }
+ else
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "ref count is %d, not closing\n", pVmaList->m_refCount);
+ }
+ }
+ else
+ {
+ PRINTK_VERBOSE(KERN_ERR "uh-oh, vma %p not found (%s %d)!\n", pVma, current->comm, current->pid);
+ PRINTK_VERBOSE(KERN_ERR "CLOSE ERR\n");
+ }
+
+ PRINTK_VERBOSE(KERN_DEBUG "CLOSE %p %d %d pages (tracked pages %d)",
+ pVma, current->pid, freed, g_trackedPages);
+
+ PRINTK_VERBOSE(KERN_DEBUG "%d pages open\n", g_trackedPages);
+}
+
+static int VmaFault4k(struct vm_area_struct *pVma, struct vm_fault *pVmf)
+{
+ PRINTK_VERBOSE(KERN_DEBUG "vma fault for vma %p private %p at offset %ld (%s %d)\n", pVma, pVma->vm_private_data, pVmf->pgoff,
+ current->comm, current->pid);
+ PRINTK_VERBOSE(KERN_DEBUG "FAULT\n");
+ pVmf->page = alloc_page(GFP_KERNEL);
+
+ if (pVmf->page)
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "alloc page virtual %p\n", page_address(pVmf->page));
+ }
+
+ if (!pVmf->page)
+ {
+ PRINTK(KERN_ERR "vma fault oom (%s %d)\n", current->comm, current->pid);
+ return VM_FAULT_OOM;
+ }
+ else
+ {
+ struct VmaPageList *pVmaList;
+
+ get_page(pVmf->page);
+ g_trackedPages++;
+
+ //find our vma in the list
+ pVmaList = (struct VmaPageList *)pVma->vm_private_data;
+
+ if (pVmaList)
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "vma found (%s %d)\n", current->comm, current->pid);
+
+ if (pVmaList->m_pPageTail->m_used == PAGES_PER_LIST)
+ {
+ PRINTK_VERBOSE(KERN_DEBUG "making new page list (%s %d)\n", current->comm, current->pid);
+ //making a new page list
+ pVmaList->m_pPageTail->m_pNext = (struct PageList *)kmalloc(sizeof(struct PageList), GFP_KERNEL);
+ if (!pVmaList->m_pPageTail->m_pNext)
+ return -ENOMEM;
+
+ //update the tail pointer
+ pVmaList->m_pPageTail = pVmaList->m_pPageTail->m_pNext;
+ pVmaList->m_pPageTail->m_used = 0;
+ pVmaList->m_pPageTail->m_pNext = 0;
+ }
+
+ PRINTK_VERBOSE(KERN_DEBUG "adding page to list (%s %d)\n", current->comm, current->pid);
+
+ pVmaList->m_pPageTail->m_pPages[pVmaList->m_pPageTail->m_used] = pVmf->page;
+ pVmaList->m_pPageTail->m_used++;
+ }
+ else
+ PRINTK(KERN_ERR "returned page for vma we don\'t know %p (%s %d)\n", pVma, current->comm, current->pid);
+
+ return 0;
+ }
+}
+
+/****** GENERIC FUNCTIONS ******/
+static int __init dmaer_init(void)
+{
+ int result = alloc_chrdev_region(&g_majorMinor, 0, 1, "dmaer");
+ if (result < 0)
+ {
+ PRINTK(KERN_ERR "unable to get major device number\n");
+ return result;
+ }
+ else
+ PRINTK(KERN_DEBUG "major device number %d\n", MAJOR(g_majorMinor));
+
+ PRINTK(KERN_DEBUG "vma list size %d, page list size %d, page size %ld\n",
+ sizeof(struct VmaPageList), sizeof(struct PageList), PAGE_SIZE);
+
+ //get a dma channel to work with
+ result = bcm_dma_chan_alloc(BCM_DMA_FEATURE_FAST, (void **)&g_pDmaChanBase, &g_dmaIrq);
+
+ //uncomment to force to channel 0
+ //result = 0;
+ //g_pDmaChanBase = 0xce808000;
+
+ if (result < 0)
+ {
+ PRINTK(KERN_ERR "failed to allocate dma channel\n");
+ cdev_del(&g_cDev);
+ unregister_chrdev_region(g_majorMinor, 1);
+ }
+
+ //reset the channel
+ PRINTK(KERN_DEBUG "allocated dma channel %d (%p), initial state %08x\n", result, g_pDmaChanBase, *g_pDmaChanBase);
+ *g_pDmaChanBase = 1 << 31;
+ PRINTK(KERN_DEBUG "post-reset %08x\n", *g_pDmaChanBase);
+
+ g_dmaChan = result;
+
+ //clear the cache stats
+ g_cacheHit = 0;
+ g_cacheMiss = 0;
+
+ //register our device - after this we are go go go
+ cdev_init(&g_cDev, &g_fOps);
+ g_cDev.owner = THIS_MODULE;
+ g_cDev.ops = &g_fOps;
+
+ result = cdev_add(&g_cDev, g_majorMinor, 1);
+ if (result < 0)
+ {
+ PRINTK(KERN_ERR "failed to add character device\n");
+ unregister_chrdev_region(g_majorMinor, 1);
+ bcm_dma_chan_free(g_dmaChan);
+ return result;
+ }
+
+ return 0;
+}
+
+static void __exit dmaer_exit(void)
+{
+ PRINTK(KERN_INFO "closing dmaer device, cache stats: %d hits %d misses\n", g_cacheHit, g_cacheMiss);
+ //unregister the device
+ cdev_del(&g_cDev);
+ unregister_chrdev_region(g_majorMinor, 1);
+ //free the dma channel
+ bcm_dma_chan_free(g_dmaChan);
+}
+
+MODULE_LICENSE("Dual BSD/GPL");
+MODULE_AUTHOR("Simon Hall");
+module_init(dmaer_init);
+module_exit(dmaer_exit);
+
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/arm_control.h
@@ -0,0 +1,419 @@
+/*
+ * linux/arch/arm/mach-bcm2708/arm_control.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __BCM2708_ARM_CONTROL_H
+#define __BCM2708_ARM_CONTROL_H
+
+/*
+ * Definitions and addresses for the ARM CONTROL logic
+ * This file is manually generated.
+ */
+
+#define ARM_BASE 0x7E00B000
+
+/* Basic configuration */
+#define ARM_CONTROL0 HW_REGISTER_RW(ARM_BASE+0x000)
+#define ARM_C0_SIZ128M 0x00000000
+#define ARM_C0_SIZ256M 0x00000001
+#define ARM_C0_SIZ512M 0x00000002
+#define ARM_C0_SIZ1G 0x00000003
+#define ARM_C0_BRESP0 0x00000000
+#define ARM_C0_BRESP1 0x00000004
+#define ARM_C0_BRESP2 0x00000008
+#define ARM_C0_BOOTHI 0x00000010
+#define ARM_C0_UNUSED05 0x00000020 /* free */
+#define ARM_C0_FULLPERI 0x00000040
+#define ARM_C0_UNUSED78 0x00000180 /* free */
+#define ARM_C0_JTAGMASK 0x00000E00
+#define ARM_C0_JTAGOFF 0x00000000
+#define ARM_C0_JTAGBASH 0x00000800 /* Debug on GPIO off */
+#define ARM_C0_JTAGGPIO 0x00000C00 /* Debug on GPIO on */
+#define ARM_C0_APROTMSK 0x0000F000
+#define ARM_C0_DBG0SYNC 0x00010000 /* VPU0 halt sync */
+#define ARM_C0_DBG1SYNC 0x00020000 /* VPU1 halt sync */
+#define ARM_C0_SWDBGREQ 0x00040000 /* HW debug request */
+#define ARM_C0_PASSHALT 0x00080000 /* ARM halt passed to debugger */
+#define ARM_C0_PRIO_PER 0x00F00000 /* per priority mask */
+#define ARM_C0_PRIO_L2 0x0F000000
+#define ARM_C0_PRIO_UC 0xF0000000
+
+#define ARM_C0_APROTPASS 0x0000A000 /* Translate 1:1 */
+#define ARM_C0_APROTUSER 0x00000000 /* Only user mode */
+#define ARM_C0_APROTSYST 0x0000F000 /* Only system mode */
+
+
+#define ARM_CONTROL1 HW_REGISTER_RW(ARM_BASE+0x440)
+#define ARM_C1_TIMER 0x00000001 /* re-route timer IRQ to VC */
+#define ARM_C1_MAIL 0x00000002 /* re-route Mail IRQ to VC */
+#define ARM_C1_BELL0 0x00000004 /* re-route Doorbell 0 to VC */
+#define ARM_C1_BELL1 0x00000008 /* re-route Doorbell 1 to VC */
+#define ARM_C1_PERSON 0x00000100 /* peripherals on */
+#define ARM_C1_REQSTOP 0x00000200 /* ASYNC bridge request stop */
+
+#define ARM_STATUS HW_REGISTER_RW(ARM_BASE+0x444)
+#define ARM_S_ACKSTOP 0x80000000 /* Bridge stopped */
+#define ARM_S_READPEND 0x000003FF /* pending reads counter */
+#define ARM_S_WRITPEND 0x000FFC00 /* pending writes counter */
+
+#define ARM_ERRHALT HW_REGISTER_RW(ARM_BASE+0x448)
+#define ARM_EH_PERIBURST 0x00000001 /* Burst write seen on peri bus */
+#define ARM_EH_ILLADDRS1 0x00000002 /* Address bits 25-27 error */
+#define ARM_EH_ILLADDRS2 0x00000004 /* Address bits 31-28 error */
+#define ARM_EH_VPU0HALT 0x00000008 /* VPU0 halted & in debug mode */
+#define ARM_EH_VPU1HALT 0x00000010 /* VPU1 halted & in debug mode */
+#define ARM_EH_ARMHALT 0x00000020 /* ARM in halted debug mode */
+
+#define ARM_ID_SECURE HW_REGISTER_RW(ARM_BASE+0x00C)
+#define ARM_ID HW_REGISTER_RW(ARM_BASE+0x44C)
+#define ARM_IDVAL 0x364D5241
+
+/* Translation memory */
+#define ARM_TRANSLATE HW_REGISTER_RW(ARM_BASE+0x100)
+/* 32 locations: 0x100.. 0x17F */
+/* 32 spare means we CAN go to 64 pages.... */
+
+
+/* Interrupts */
+#define ARM_IRQ_PEND0 HW_REGISTER_RW(ARM_BASE+0x200) /* Top IRQ bits */
+#define ARM_I0_TIMER 0x00000001 /* timer IRQ */
+#define ARM_I0_MAIL 0x00000002 /* Mail IRQ */
+#define ARM_I0_BELL0 0x00000004 /* Doorbell 0 */
+#define ARM_I0_BELL1 0x00000008 /* Doorbell 1 */
+#define ARM_I0_BANK1 0x00000100 /* Bank1 IRQ */
+#define ARM_I0_BANK2 0x00000200 /* Bank2 IRQ */
+
+#define ARM_IRQ_PEND1 HW_REGISTER_RW(ARM_BASE+0x204) /* All bank1 IRQ bits */
+/* todo: all I1_interrupt sources */
+#define ARM_IRQ_PEND2 HW_REGISTER_RW(ARM_BASE+0x208) /* All bank2 IRQ bits */
+/* todo: all I2_interrupt sources */
+
+#define ARM_IRQ_FAST HW_REGISTER_RW(ARM_BASE+0x20C) /* FIQ control */
+#define ARM_IF_INDEX 0x0000007F /* FIQ select */
+#define ARM_IF_ENABLE 0x00000080 /* FIQ enable */
+#define ARM_IF_VCMASK 0x0000003F /* FIQ = (index from VC source) */
+#define ARM_IF_TIMER 0x00000040 /* FIQ = ARM timer */
+#define ARM_IF_MAIL 0x00000041 /* FIQ = ARM Mail */
+#define ARM_IF_BELL0 0x00000042 /* FIQ = ARM Doorbell 0 */
+#define ARM_IF_BELL1 0x00000043 /* FIQ = ARM Doorbell 1 */
+#define ARM_IF_VP0HALT 0x00000044 /* FIQ = VPU0 Halt seen */
+#define ARM_IF_VP1HALT 0x00000045 /* FIQ = VPU1 Halt seen */
+#define ARM_IF_ILLEGAL 0x00000046 /* FIQ = Illegal access seen */
+
+#define ARM_IRQ_ENBL1 HW_REGISTER_RW(ARM_BASE+0x210) /* Bank1 enable bits */
+#define ARM_IRQ_ENBL2 HW_REGISTER_RW(ARM_BASE+0x214) /* Bank2 enable bits */
+#define ARM_IRQ_ENBL3 HW_REGISTER_RW(ARM_BASE+0x218) /* ARM irqs enable bits */
+#define ARM_IRQ_DIBL1 HW_REGISTER_RW(ARM_BASE+0x21C) /* Bank1 disable bits */
+#define ARM_IRQ_DIBL2 HW_REGISTER_RW(ARM_BASE+0x220) /* Bank2 disable bits */
+#define ARM_IRQ_DIBL3 HW_REGISTER_RW(ARM_BASE+0x224) /* ARM irqs disable bits */
+#define ARM_IE_TIMER 0x00000001 /* Timer IRQ */
+#define ARM_IE_MAIL 0x00000002 /* Mail IRQ */
+#define ARM_IE_BELL0 0x00000004 /* Doorbell 0 */
+#define ARM_IE_BELL1 0x00000008 /* Doorbell 1 */
+#define ARM_IE_VP0HALT 0x00000010 /* VPU0 Halt */
+#define ARM_IE_VP1HALT 0x00000020 /* VPU1 Halt */
+#define ARM_IE_ILLEGAL 0x00000040 /* Illegal access seen */
+
+/* Timer */
+/* For reg. fields see sp804 spec. */
+#define ARM_T_LOAD HW_REGISTER_RW(ARM_BASE+0x400)
+#define ARM_T_VALUE HW_REGISTER_RW(ARM_BASE+0x404)
+#define ARM_T_CONTROL HW_REGISTER_RW(ARM_BASE+0x408)
+#define ARM_T_IRQCNTL HW_REGISTER_RW(ARM_BASE+0x40C)
+#define ARM_T_RAWIRQ HW_REGISTER_RW(ARM_BASE+0x410)
+#define ARM_T_MSKIRQ HW_REGISTER_RW(ARM_BASE+0x414)
+#define ARM_T_RELOAD HW_REGISTER_RW(ARM_BASE+0x418)
+#define ARM_T_PREDIV HW_REGISTER_RW(ARM_BASE+0x41c)
+#define ARM_T_FREECNT HW_REGISTER_RW(ARM_BASE+0x420)
+
+#define TIMER_CTRL_ONESHOT (1 << 0)
+#define TIMER_CTRL_32BIT (1 << 1)
+#define TIMER_CTRL_DIV1 (0 << 2)
+#define TIMER_CTRL_DIV16 (1 << 2)
+#define TIMER_CTRL_DIV256 (2 << 2)
+#define TIMER_CTRL_IE (1 << 5)
+#define TIMER_CTRL_PERIODIC (1 << 6)
+#define TIMER_CTRL_ENABLE (1 << 7)
+#define TIMER_CTRL_DBGHALT (1 << 8)
+#define TIMER_CTRL_ENAFREE (1 << 9)
+#define TIMER_CTRL_FREEDIV_SHIFT 16)
+#define TIMER_CTRL_FREEDIV_MASK 0xff
+
+/* Semaphores, Doorbells, Mailboxes */
+#define ARM_SBM_OWN0 (ARM_BASE+0x800)
+#define ARM_SBM_OWN1 (ARM_BASE+0x900)
+#define ARM_SBM_OWN2 (ARM_BASE+0xA00)
+#define ARM_SBM_OWN3 (ARM_BASE+0xB00)
+
+/* MAILBOXES
+ * Register flags are common across all
+ * owner registers. See end of this section
+ *
+ * Semaphores, Doorbells, Mailboxes Owner 0
+ *
+ */
+
+#define ARM_0_SEMS HW_REGISTER_RW(ARM_SBM_OWN0+0x00)
+#define ARM_0_SEM0 HW_REGISTER_RW(ARM_SBM_OWN0+0x00)
+#define ARM_0_SEM1 HW_REGISTER_RW(ARM_SBM_OWN0+0x04)
+#define ARM_0_SEM2 HW_REGISTER_RW(ARM_SBM_OWN0+0x08)
+#define ARM_0_SEM3 HW_REGISTER_RW(ARM_SBM_OWN0+0x0C)
+#define ARM_0_SEM4 HW_REGISTER_RW(ARM_SBM_OWN0+0x10)
+#define ARM_0_SEM5 HW_REGISTER_RW(ARM_SBM_OWN0+0x14)
+#define ARM_0_SEM6 HW_REGISTER_RW(ARM_SBM_OWN0+0x18)
+#define ARM_0_SEM7 HW_REGISTER_RW(ARM_SBM_OWN0+0x1C)
+#define ARM_0_BELL0 HW_REGISTER_RW(ARM_SBM_OWN0+0x40)
+#define ARM_0_BELL1 HW_REGISTER_RW(ARM_SBM_OWN0+0x44)
+#define ARM_0_BELL2 HW_REGISTER_RW(ARM_SBM_OWN0+0x48)
+#define ARM_0_BELL3 HW_REGISTER_RW(ARM_SBM_OWN0+0x4C)
+/* MAILBOX 0 access in Owner 0 area */
+/* Some addresses should ONLY be used by owner 0 */
+#define ARM_0_MAIL0_WRT HW_REGISTER_RW(ARM_SBM_OWN0+0x80) /* .. 0x8C (4 locations) */
+#define ARM_0_MAIL0_RD HW_REGISTER_RW(ARM_SBM_OWN0+0x80) /* .. 0x8C (4 locations) Normal read */
+#define ARM_0_MAIL0_POL HW_REGISTER_RW(ARM_SBM_OWN0+0x90) /* none-pop read */
+#define ARM_0_MAIL0_SND HW_REGISTER_RW(ARM_SBM_OWN0+0x94) /* Sender read (only LS 2 bits) */
+#define ARM_0_MAIL0_STA HW_REGISTER_RW(ARM_SBM_OWN0+0x98) /* Status read */
+#define ARM_0_MAIL0_CNF HW_REGISTER_RW(ARM_SBM_OWN0+0x9C) /* Config read/write */
+/* MAILBOX 1 access in Owner 0 area */
+/* Owner 0 should only WRITE to this mailbox */
+#define ARM_0_MAIL1_WRT HW_REGISTER_RW(ARM_SBM_OWN0+0xA0) /* .. 0xAC (4 locations) */
+/*#define ARM_0_MAIL1_RD HW_REGISTER_RW(ARM_SBM_OWN0+0xA0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_0_MAIL1_POL HW_REGISTER_RW(ARM_SBM_OWN0+0xB0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_0_MAIL1_SND HW_REGISTER_RW(ARM_SBM_OWN0+0xB4) */ /* DO NOT USE THIS !!!!! */
+#define ARM_0_MAIL1_STA HW_REGISTER_RW(ARM_SBM_OWN0+0xB8) /* Status read */
+/*#define ARM_0_MAIL1_CNF HW_REGISTER_RW(ARM_SBM_OWN0+0xBC) */ /* DO NOT USE THIS !!!!! */
+/* General SEM, BELL, MAIL config/status */
+#define ARM_0_SEMCLRDBG HW_REGISTER_RW(ARM_SBM_OWN0+0xE0) /* semaphore clear/debug register */
+#define ARM_0_BELLCLRDBG HW_REGISTER_RW(ARM_SBM_OWN0+0xE4) /* Doorbells clear/debug register */
+#define ARM_0_ALL_IRQS HW_REGISTER_RW(ARM_SBM_OWN0+0xF8) /* ALL interrupts */
+#define ARM_0_MY_IRQS HW_REGISTER_RW(ARM_SBM_OWN0+0xFC) /* IRQS pending for owner 0 */
+
+/* Semaphores, Doorbells, Mailboxes Owner 1 */
+#define ARM_1_SEMS HW_REGISTER_RW(ARM_SBM_OWN1+0x00)
+#define ARM_1_SEM0 HW_REGISTER_RW(ARM_SBM_OWN1+0x00)
+#define ARM_1_SEM1 HW_REGISTER_RW(ARM_SBM_OWN1+0x04)
+#define ARM_1_SEM2 HW_REGISTER_RW(ARM_SBM_OWN1+0x08)
+#define ARM_1_SEM3 HW_REGISTER_RW(ARM_SBM_OWN1+0x0C)
+#define ARM_1_SEM4 HW_REGISTER_RW(ARM_SBM_OWN1+0x10)
+#define ARM_1_SEM5 HW_REGISTER_RW(ARM_SBM_OWN1+0x14)
+#define ARM_1_SEM6 HW_REGISTER_RW(ARM_SBM_OWN1+0x18)
+#define ARM_1_SEM7 HW_REGISTER_RW(ARM_SBM_OWN1+0x1C)
+#define ARM_1_BELL0 HW_REGISTER_RW(ARM_SBM_OWN1+0x40)
+#define ARM_1_BELL1 HW_REGISTER_RW(ARM_SBM_OWN1+0x44)
+#define ARM_1_BELL2 HW_REGISTER_RW(ARM_SBM_OWN1+0x48)
+#define ARM_1_BELL3 HW_REGISTER_RW(ARM_SBM_OWN1+0x4C)
+/* MAILBOX 0 access in Owner 0 area */
+/* Owner 1 should only WRITE to this mailbox */
+#define ARM_1_MAIL0_WRT HW_REGISTER_RW(ARM_SBM_OWN1+0x80) /* .. 0x8C (4 locations) */
+/*#define ARM_1_MAIL0_RD HW_REGISTER_RW(ARM_SBM_OWN1+0x80) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_1_MAIL0_POL HW_REGISTER_RW(ARM_SBM_OWN1+0x90) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_1_MAIL0_SND HW_REGISTER_RW(ARM_SBM_OWN1+0x94) */ /* DO NOT USE THIS !!!!! */
+#define ARM_1_MAIL0_STA HW_REGISTER_RW(ARM_SBM_OWN1+0x98) /* Status read */
+/*#define ARM_1_MAIL0_CNF HW_REGISTER_RW(ARM_SBM_OWN1+0x9C) */ /* DO NOT USE THIS !!!!! */
+/* MAILBOX 1 access in Owner 0 area */
+#define ARM_1_MAIL1_WRT HW_REGISTER_RW(ARM_SBM_OWN1+0xA0) /* .. 0xAC (4 locations) */
+#define ARM_1_MAIL1_RD HW_REGISTER_RW(ARM_SBM_OWN1+0xA0) /* .. 0xAC (4 locations) Normal read */
+#define ARM_1_MAIL1_POL HW_REGISTER_RW(ARM_SBM_OWN1+0xB0) /* none-pop read */
+#define ARM_1_MAIL1_SND HW_REGISTER_RW(ARM_SBM_OWN1+0xB4) /* Sender read (only LS 2 bits) */
+#define ARM_1_MAIL1_STA HW_REGISTER_RW(ARM_SBM_OWN1+0xB8) /* Status read */
+#define ARM_1_MAIL1_CNF HW_REGISTER_RW(ARM_SBM_OWN1+0xBC)
+/* General SEM, BELL, MAIL config/status */
+#define ARM_1_SEMCLRDBG HW_REGISTER_RW(ARM_SBM_OWN1+0xE0) /* semaphore clear/debug register */
+#define ARM_1_BELLCLRDBG HW_REGISTER_RW(ARM_SBM_OWN1+0xE4) /* Doorbells clear/debug register */
+#define ARM_1_MY_IRQS HW_REGISTER_RW(ARM_SBM_OWN1+0xFC) /* IRQS pending for owner 1 */
+#define ARM_1_ALL_IRQS HW_REGISTER_RW(ARM_SBM_OWN1+0xF8) /* ALL interrupts */
+
+/* Semaphores, Doorbells, Mailboxes Owner 2 */
+#define ARM_2_SEMS HW_REGISTER_RW(ARM_SBM_OWN2+0x00)
+#define ARM_2_SEM0 HW_REGISTER_RW(ARM_SBM_OWN2+0x00)
+#define ARM_2_SEM1 HW_REGISTER_RW(ARM_SBM_OWN2+0x04)
+#define ARM_2_SEM2 HW_REGISTER_RW(ARM_SBM_OWN2+0x08)
+#define ARM_2_SEM3 HW_REGISTER_RW(ARM_SBM_OWN2+0x0C)
+#define ARM_2_SEM4 HW_REGISTER_RW(ARM_SBM_OWN2+0x10)
+#define ARM_2_SEM5 HW_REGISTER_RW(ARM_SBM_OWN2+0x14)
+#define ARM_2_SEM6 HW_REGISTER_RW(ARM_SBM_OWN2+0x18)
+#define ARM_2_SEM7 HW_REGISTER_RW(ARM_SBM_OWN2+0x1C)
+#define ARM_2_BELL0 HW_REGISTER_RW(ARM_SBM_OWN2+0x40)
+#define ARM_2_BELL1 HW_REGISTER_RW(ARM_SBM_OWN2+0x44)
+#define ARM_2_BELL2 HW_REGISTER_RW(ARM_SBM_OWN2+0x48)
+#define ARM_2_BELL3 HW_REGISTER_RW(ARM_SBM_OWN2+0x4C)
+/* MAILBOX 0 access in Owner 2 area */
+/* Owner 2 should only WRITE to this mailbox */
+#define ARM_2_MAIL0_WRT HW_REGISTER_RW(ARM_SBM_OWN2+0x80) /* .. 0x8C (4 locations) */
+/*#define ARM_2_MAIL0_RD HW_REGISTER_RW(ARM_SBM_OWN2+0x80) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL0_POL HW_REGISTER_RW(ARM_SBM_OWN2+0x90) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL0_SND HW_REGISTER_RW(ARM_SBM_OWN2+0x94) */ /* DO NOT USE THIS !!!!! */
+#define ARM_2_MAIL0_STA HW_REGISTER_RW(ARM_SBM_OWN2+0x98) /* Status read */
+/*#define ARM_2_MAIL0_CNF HW_REGISTER_RW(ARM_SBM_OWN2+0x9C) */ /* DO NOT USE THIS !!!!! */
+/* MAILBOX 1 access in Owner 2 area */
+/* Owner 2 should only WRITE to this mailbox */
+#define ARM_2_MAIL1_WRT HW_REGISTER_RW(ARM_SBM_OWN2+0xA0) /* .. 0xAC (4 locations) */
+/*#define ARM_2_MAIL1_RD HW_REGISTER_RW(ARM_SBM_OWN2+0xA0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL1_POL HW_REGISTER_RW(ARM_SBM_OWN2+0xB0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_2_MAIL1_SND HW_REGISTER_RW(ARM_SBM_OWN2+0xB4) */ /* DO NOT USE THIS !!!!! */
+#define ARM_2_MAIL1_STA HW_REGISTER_RW(ARM_SBM_OWN2+0xB8) /* Status read */
+/*#define ARM_2_MAIL1_CNF HW_REGISTER_RW(ARM_SBM_OWN2+0xBC) */ /* DO NOT USE THIS !!!!! */
+/* General SEM, BELL, MAIL config/status */
+#define ARM_2_SEMCLRDBG HW_REGISTER_RW(ARM_SBM_OWN2+0xE0) /* semaphore clear/debug register */
+#define ARM_2_BELLCLRDBG HW_REGISTER_RW(ARM_SBM_OWN2+0xE4) /* Doorbells clear/debug register */
+#define ARM_2_MY_IRQS HW_REGISTER_RW(ARM_SBM_OWN2+0xFC) /* IRQS pending for owner 2 */
+#define ARM_2_ALL_IRQS HW_REGISTER_RW(ARM_SBM_OWN2+0xF8) /* ALL interrupts */
+
+/* Semaphores, Doorbells, Mailboxes Owner 3 */
+#define ARM_3_SEMS HW_REGISTER_RW(ARM_SBM_OWN3+0x00)
+#define ARM_3_SEM0 HW_REGISTER_RW(ARM_SBM_OWN3+0x00)
+#define ARM_3_SEM1 HW_REGISTER_RW(ARM_SBM_OWN3+0x04)
+#define ARM_3_SEM2 HW_REGISTER_RW(ARM_SBM_OWN3+0x08)
+#define ARM_3_SEM3 HW_REGISTER_RW(ARM_SBM_OWN3+0x0C)
+#define ARM_3_SEM4 HW_REGISTER_RW(ARM_SBM_OWN3+0x10)
+#define ARM_3_SEM5 HW_REGISTER_RW(ARM_SBM_OWN3+0x14)
+#define ARM_3_SEM6 HW_REGISTER_RW(ARM_SBM_OWN3+0x18)
+#define ARM_3_SEM7 HW_REGISTER_RW(ARM_SBM_OWN3+0x1C)
+#define ARM_3_BELL0 HW_REGISTER_RW(ARM_SBM_OWN3+0x40)
+#define ARM_3_BELL1 HW_REGISTER_RW(ARM_SBM_OWN3+0x44)
+#define ARM_3_BELL2 HW_REGISTER_RW(ARM_SBM_OWN3+0x48)
+#define ARM_3_BELL3 HW_REGISTER_RW(ARM_SBM_OWN3+0x4C)
+/* MAILBOX 0 access in Owner 3 area */
+/* Owner 3 should only WRITE to this mailbox */
+#define ARM_3_MAIL0_WRT HW_REGISTER_RW(ARM_SBM_OWN3+0x80) /* .. 0x8C (4 locations) */
+/*#define ARM_3_MAIL0_RD HW_REGISTER_RW(ARM_SBM_OWN3+0x80) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL0_POL HW_REGISTER_RW(ARM_SBM_OWN3+0x90) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL0_SND HW_REGISTER_RW(ARM_SBM_OWN3+0x94) */ /* DO NOT USE THIS !!!!! */
+#define ARM_3_MAIL0_STA HW_REGISTER_RW(ARM_SBM_OWN3+0x98) /* Status read */
+/*#define ARM_3_MAIL0_CNF HW_REGISTER_RW(ARM_SBM_OWN3+0x9C) */ /* DO NOT USE THIS !!!!! */
+/* MAILBOX 1 access in Owner 3 area */
+/* Owner 3 should only WRITE to this mailbox */
+#define ARM_3_MAIL1_WRT HW_REGISTER_RW(ARM_SBM_OWN3+0xA0) /* .. 0xAC (4 locations) */
+/*#define ARM_3_MAIL1_RD HW_REGISTER_RW(ARM_SBM_OWN3+0xA0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL1_POL HW_REGISTER_RW(ARM_SBM_OWN3+0xB0) */ /* DO NOT USE THIS !!!!! */
+/*#define ARM_3_MAIL1_SND HW_REGISTER_RW(ARM_SBM_OWN3+0xB4) */ /* DO NOT USE THIS !!!!! */
+#define ARM_3_MAIL1_STA HW_REGISTER_RW(ARM_SBM_OWN3+0xB8) /* Status read */
+/*#define ARM_3_MAIL1_CNF HW_REGISTER_RW(ARM_SBM_OWN3+0xBC) */ /* DO NOT USE THIS !!!!! */
+/* General SEM, BELL, MAIL config/status */
+#define ARM_3_SEMCLRDBG HW_REGISTER_RW(ARM_SBM_OWN3+0xE0) /* semaphore clear/debug register */
+#define ARM_3_BELLCLRDBG HW_REGISTER_RW(ARM_SBM_OWN3+0xE4) /* Doorbells clear/debug register */
+#define ARM_3_MY_IRQS HW_REGISTER_RW(ARM_SBM_OWN3+0xFC) /* IRQS pending for owner 3 */
+#define ARM_3_ALL_IRQS HW_REGISTER_RW(ARM_SBM_OWN3+0xF8) /* ALL interrupts */
+
+
+
+/* Mailbox flags. Valid for all owners */
+
+/* Mailbox status register (...0x98) */
+#define ARM_MS_FULL 0x80000000
+#define ARM_MS_EMPTY 0x40000000
+#define ARM_MS_LEVEL 0x400000FF /* Max. value depdnds on mailbox depth parameter */
+
+/* MAILBOX config/status register (...0x9C) */
+/* ANY write to this register clears the error bits! */
+#define ARM_MC_IHAVEDATAIRQEN 0x00000001 /* mailbox irq enable: has data */
+#define ARM_MC_IHAVESPACEIRQEN 0x00000002 /* mailbox irq enable: has space */
+#define ARM_MC_OPPISEMPTYIRQEN 0x00000004 /* mailbox irq enable: Opp. is empty */
+#define ARM_MC_MAIL_CLEAR 0x00000008 /* mailbox clear write 1, then 0 */
+#define ARM_MC_IHAVEDATAIRQPEND 0x00000010 /* mailbox irq pending: has space */
+#define ARM_MC_IHAVESPACEIRQPEND 0x00000020 /* mailbox irq pending: Opp. is empty */
+#define ARM_MC_OPPISEMPTYIRQPEND 0x00000040 /* mailbox irq pending */
+/* Bit 7 is unused */
+#define ARM_MC_ERRNOOWN 0x00000100 /* error : none owner read from mailbox */
+#define ARM_MC_ERROVERFLW 0x00000200 /* error : write to fill mailbox */
+#define ARM_MC_ERRUNDRFLW 0x00000400 /* error : read from empty mailbox */
+
+/* Semaphore clear/debug register (...0xE0) */
+#define ARM_SD_OWN0 0x00000003 /* Owner of sem 0 */
+#define ARM_SD_OWN1 0x0000000C /* Owner of sem 1 */
+#define ARM_SD_OWN2 0x00000030 /* Owner of sem 2 */
+#define ARM_SD_OWN3 0x000000C0 /* Owner of sem 3 */
+#define ARM_SD_OWN4 0x00000300 /* Owner of sem 4 */
+#define ARM_SD_OWN5 0x00000C00 /* Owner of sem 5 */
+#define ARM_SD_OWN6 0x00003000 /* Owner of sem 6 */
+#define ARM_SD_OWN7 0x0000C000 /* Owner of sem 7 */
+#define ARM_SD_SEM0 0x00010000 /* Status of sem 0 */
+#define ARM_SD_SEM1 0x00020000 /* Status of sem 1 */
+#define ARM_SD_SEM2 0x00040000 /* Status of sem 2 */
+#define ARM_SD_SEM3 0x00080000 /* Status of sem 3 */
+#define ARM_SD_SEM4 0x00100000 /* Status of sem 4 */
+#define ARM_SD_SEM5 0x00200000 /* Status of sem 5 */
+#define ARM_SD_SEM6 0x00400000 /* Status of sem 6 */
+#define ARM_SD_SEM7 0x00800000 /* Status of sem 7 */
+
+/* Doorbells clear/debug register (...0xE4) */
+#define ARM_BD_OWN0 0x00000003 /* Owner of doorbell 0 */
+#define ARM_BD_OWN1 0x0000000C /* Owner of doorbell 1 */
+#define ARM_BD_OWN2 0x00000030 /* Owner of doorbell 2 */
+#define ARM_BD_OWN3 0x000000C0 /* Owner of doorbell 3 */
+#define ARM_BD_BELL0 0x00000100 /* Status of doorbell 0 */
+#define ARM_BD_BELL1 0x00000200 /* Status of doorbell 1 */
+#define ARM_BD_BELL2 0x00000400 /* Status of doorbell 2 */
+#define ARM_BD_BELL3 0x00000800 /* Status of doorbell 3 */
+
+/* MY IRQS register (...0xF8) */
+#define ARM_MYIRQ_BELL 0x00000001 /* This owner has a doorbell IRQ */
+#define ARM_MYIRQ_MAIL 0x00000002 /* This owner has a mailbox IRQ */
+
+/* ALL IRQS register (...0xF8) */
+#define ARM_AIS_BELL0 0x00000001 /* Doorbell 0 IRQ pending */
+#define ARM_AIS_BELL1 0x00000002 /* Doorbell 1 IRQ pending */
+#define ARM_AIS_BELL2 0x00000004 /* Doorbell 2 IRQ pending */
+#define ARM_AIS_BELL3 0x00000008 /* Doorbell 3 IRQ pending */
+#define ARM_AIS0_HAVEDATA 0x00000010 /* MAIL 0 has data IRQ pending */
+#define ARM_AIS0_HAVESPAC 0x00000020 /* MAIL 0 has space IRQ pending */
+#define ARM_AIS0_OPPEMPTY 0x00000040 /* MAIL 0 opposite is empty IRQ */
+#define ARM_AIS1_HAVEDATA 0x00000080 /* MAIL 1 has data IRQ pending */
+#define ARM_AIS1_HAVESPAC 0x00000100 /* MAIL 1 has space IRQ pending */
+#define ARM_AIS1_OPPEMPTY 0x00000200 /* MAIL 1 opposite is empty IRQ */
+/* Note that bell-0, bell-1 and MAIL0 IRQ go only to the ARM */
+/* Whilst that bell-2, bell-3 and MAIL1 IRQ go only to the VC */
+/* */
+/* ARM JTAG BASH */
+/* */
+#define AJB_BASE 0x7e2000c0
+
+#define AJBCONF HW_REGISTER_RW(AJB_BASE+0x00)
+#define AJB_BITS0 0x000000
+#define AJB_BITS4 0x000004
+#define AJB_BITS8 0x000008
+#define AJB_BITS12 0x00000C
+#define AJB_BITS16 0x000010
+#define AJB_BITS20 0x000014
+#define AJB_BITS24 0x000018
+#define AJB_BITS28 0x00001C
+#define AJB_BITS32 0x000020
+#define AJB_BITS34 0x000022
+#define AJB_OUT_MS 0x000040
+#define AJB_OUT_LS 0x000000
+#define AJB_INV_CLK 0x000080
+#define AJB_D0_RISE 0x000100
+#define AJB_D0_FALL 0x000000
+#define AJB_D1_RISE 0x000200
+#define AJB_D1_FALL 0x000000
+#define AJB_IN_RISE 0x000400
+#define AJB_IN_FALL 0x000000
+#define AJB_ENABLE 0x000800
+#define AJB_HOLD0 0x000000
+#define AJB_HOLD1 0x001000
+#define AJB_HOLD2 0x002000
+#define AJB_HOLD3 0x003000
+#define AJB_RESETN 0x004000
+#define AJB_CLKSHFT 16
+#define AJB_BUSY 0x80000000
+#define AJBTMS HW_REGISTER_RW(AJB_BASE+0x04)
+#define AJBTDI HW_REGISTER_RW(AJB_BASE+0x08)
+#define AJBTDO HW_REGISTER_RW(AJB_BASE+0x0c)
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/arm_power.h
@@ -0,0 +1,60 @@
+/*
+ * linux/arch/arm/mach-bcm2708/include/mach/arm_power.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _ARM_POWER_H
+#define _ARM_POWER_H
+
+/* Use meaningful names on each side */
+#ifdef __VIDEOCORE__
+#define PREFIX(x) ARM_##x
+#else
+#define PREFIX(x) BCM_##x
+#endif
+
+enum {
+ PREFIX(POWER_SDCARD_BIT),
+ PREFIX(POWER_UART_BIT),
+ PREFIX(POWER_MINIUART_BIT),
+ PREFIX(POWER_USB_BIT),
+ PREFIX(POWER_I2C0_BIT),
+ PREFIX(POWER_I2C1_BIT),
+ PREFIX(POWER_I2C2_BIT),
+ PREFIX(POWER_SPI_BIT),
+ PREFIX(POWER_CCP2TX_BIT),
+
+ PREFIX(POWER_MAX)
+};
+
+enum {
+ PREFIX(POWER_SDCARD) = (1 << PREFIX(POWER_SDCARD_BIT)),
+ PREFIX(POWER_UART) = (1 << PREFIX(POWER_UART_BIT)),
+ PREFIX(POWER_MINIUART) = (1 << PREFIX(POWER_MINIUART_BIT)),
+ PREFIX(POWER_USB) = (1 << PREFIX(POWER_USB_BIT)),
+ PREFIX(POWER_I2C0) = (1 << PREFIX(POWER_I2C0_BIT)),
+ PREFIX(POWER_I2C1_MASK) = (1 << PREFIX(POWER_I2C1_BIT)),
+ PREFIX(POWER_I2C2_MASK) = (1 << PREFIX(POWER_I2C2_BIT)),
+ PREFIX(POWER_SPI_MASK) = (1 << PREFIX(POWER_SPI_BIT)),
+ PREFIX(POWER_CCP2TX_MASK) = (1 << PREFIX(POWER_CCP2TX_BIT)),
+
+ PREFIX(POWER_MASK) = (1 << PREFIX(POWER_MAX)) - 1,
+ PREFIX(POWER_NONE) = 0
+};
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/clkdev.h
@@ -0,0 +1,7 @@
+#ifndef __ASM_MACH_CLKDEV_H
+#define __ASM_MACH_CLKDEV_H
+
+#define __clk_get(clk) ({ 1; })
+#define __clk_put(clk) do { } while (0)
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/debug-macro.S
@@ -0,0 +1,22 @@
+/* arch/arm/mach-bcm2708/include/mach/debug-macro.S
+ *
+ * Debugging macro include header
+ *
+ * Copyright (C) 2010 Broadcom
+ * Copyright (C) 1994-1999 Russell King
+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <mach/platform.h>
+
+ .macro addruart, rp, rv, tmp
+ ldr \rp, =UART0_BASE
+ ldr \rv, =IO_ADDRESS(UART0_BASE)
+ .endm
+
+#include <asm/hardware/debug-pl01x.S>
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/dma.h
@@ -0,0 +1,86 @@
+/*
+ * linux/arch/arm/mach-bcm2708/include/mach/dma.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+
+#ifndef _MACH_BCM2708_DMA_H
+#define _MACH_BCM2708_DMA_H
+
+#define BCM_DMAMAN_DRIVER_NAME "bcm2708_dma"
+
+/* DMA CS Control and Status bits */
+#define BCM2708_DMA_ACTIVE (1 << 0)
+#define BCM2708_DMA_INT (1 << 2)
+#define BCM2708_DMA_ISPAUSED (1 << 4) /* Pause requested or not active */
+#define BCM2708_DMA_ISHELD (1 << 5) /* Is held by DREQ flow control */
+#define BCM2708_DMA_ERR (1 << 8)
+#define BCM2708_DMA_ABORT (1 << 30) /* stop current CB, go to next, WO */
+#define BCM2708_DMA_RESET (1 << 31) /* WO, self clearing */
+
+/* DMA control block "info" field bits */
+#define BCM2708_DMA_INT_EN (1 << 0)
+#define BCM2708_DMA_TDMODE (1 << 1)
+#define BCM2708_DMA_WAIT_RESP (1 << 3)
+#define BCM2708_DMA_D_INC (1 << 4)
+#define BCM2708_DMA_D_WIDTH (1 << 5)
+#define BCM2708_DMA_D_DREQ (1 << 6)
+#define BCM2708_DMA_S_INC (1 << 8)
+#define BCM2708_DMA_S_WIDTH (1 << 9)
+#define BCM2708_DMA_S_DREQ (1 << 10)
+
+#define BCM2708_DMA_BURST(x) (((x)&0xf) << 12)
+#define BCM2708_DMA_PER_MAP(x) ((x) << 16)
+#define BCM2708_DMA_WAITS(x) (((x)&0x1f) << 21)
+
+#define BCM2708_DMA_DREQ_EMMC 11
+#define BCM2708_DMA_DREQ_SDHOST 13
+
+#define BCM2708_DMA_CS 0x00 /* Control and Status */
+#define BCM2708_DMA_ADDR 0x04
+/* the current control block appears in the following registers - read only */
+#define BCM2708_DMA_INFO 0x08
+#define BCM2708_DMA_NEXTCB 0x1C
+#define BCM2708_DMA_DEBUG 0x20
+
+#define BCM2708_DMA4_CS (BCM2708_DMA_CHAN(4)+BCM2708_DMA_CS)
+#define BCM2708_DMA4_ADDR (BCM2708_DMA_CHAN(4)+BCM2708_DMA_ADDR)
+
+#define BCM2708_DMA_TDMODE_LEN(w, h) ((h) << 16 | (w))
+
+struct bcm2708_dma_cb {
+ unsigned long info;
+ unsigned long src;
+ unsigned long dst;
+ unsigned long length;
+ unsigned long stride;
+ unsigned long next;
+ unsigned long pad[2];
+};
+
+extern int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len);
+extern void bcm_dma_start(void __iomem *dma_chan_base,
+ dma_addr_t control_block);
+extern void bcm_dma_wait_idle(void __iomem *dma_chan_base);
+extern int /*rc*/ bcm_dma_abort(void __iomem *dma_chan_base);
+
+/* When listing features we can ask for when allocating DMA channels give
+ those with higher priority smaller ordinal numbers */
+#define BCM_DMA_FEATURE_FAST_ORD 0
+#define BCM_DMA_FEATURE_BULK_ORD 1
+#define BCM_DMA_FEATURE_FAST (1<<BCM_DMA_FEATURE_FAST_ORD)
+#define BCM_DMA_FEATURE_BULK (1<<BCM_DMA_FEATURE_BULK_ORD)
+#define BCM_DMA_FEATURE_COUNT 2
+
+/* return channel no or -ve error */
+extern int bcm_dma_chan_alloc(unsigned preferred_feature_set,
+ void __iomem **out_dma_base, int *out_dma_irq);
+extern int bcm_dma_chan_free(int channel);
+
+
+#endif /* _MACH_BCM2708_DMA_H */
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/entry-macro.S
@@ -0,0 +1,69 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/entry-macro.S
+ *
+ * Low-level IRQ helper macros for BCM2708 platforms
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <mach/hardware.h>
+
+ .macro disable_fiq
+ .endm
+
+ .macro get_irqnr_preamble, base, tmp
+ ldr \base, =IO_ADDRESS(ARMCTRL_IC_BASE)
+ .endm
+
+ .macro arch_ret_to_user, tmp1, tmp2
+ .endm
+
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+ /* get masked status */
+ ldr \irqstat, [\base, #(ARM_IRQ_PEND0 - ARMCTRL_IC_BASE)]
+ mov \irqnr, #(ARM_IRQ0_BASE + 31)
+ and \tmp, \irqstat, #0x300 @ save bits 8 and 9
+ /* clear bits 8 and 9, and test */
+ bics \irqstat, \irqstat, #0x300
+ bne 1010f
+
+ tst \tmp, #0x100
+ ldrne \irqstat, [\base, #(ARM_IRQ_PEND1 - ARMCTRL_IC_BASE)]
+ movne \irqnr, #(ARM_IRQ1_BASE + 31)
+ @ Mask out the interrupts also present in PEND0 - see SW-5809
+ bicne \irqstat, #((1<<7) | (1<<9) | (1<<10))
+ bicne \irqstat, #((1<<18) | (1<<19))
+ bne 1010f
+
+ tst \tmp, #0x200
+ ldrne \irqstat, [\base, #(ARM_IRQ_PEND2 - ARMCTRL_IC_BASE)]
+ movne \irqnr, #(ARM_IRQ2_BASE + 31)
+ @ Mask out the interrupts also present in PEND0 - see SW-5809
+ bicne \irqstat, #((1<<21) | (1<<22) | (1<<23) | (1<<24) | (1<<25))
+ bicne \irqstat, #((1<<30))
+ beq 1020f
+
+1010:
+ @ For non-zero x, LSB(x) = 31 - CLZ(x^(x-1))
+ @ N.B. CLZ is an ARM5 instruction.
+ sub \tmp, \irqstat, #1
+ eor \irqstat, \irqstat, \tmp
+ clz \tmp, \irqstat
+ sub \irqnr, \tmp
+
+1020: @ EQ will be set if no irqs pending
+
+ .endm
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/frc.h
@@ -0,0 +1,38 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/timex.h
+ *
+ * BCM2708 free running counter (timer)
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _MACH_FRC_H
+#define _MACH_FRC_H
+
+#define FRC_TICK_RATE (1000000)
+
+/*! Free running counter incrementing at the CLOCK_TICK_RATE
+ (slightly faster than frc_clock_ticks63()
+ */
+extern unsigned long frc_clock_ticks32(void);
+
+/*! Free running counter incrementing at the CLOCK_TICK_RATE
+ * Note - top bit should be ignored (see cnt32_to_63)
+ */
+extern unsigned long long frc_clock_ticks63(void);
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/gpio.h
@@ -0,0 +1,18 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/gpio.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_GPIO_H
+#define __ASM_ARCH_GPIO_H
+
+#define ARCH_NR_GPIOS 54 // number of gpio lines
+
+#define gpio_to_irq(x) ((x) + GPIO_IRQ_START)
+#define irq_to_gpio(x) ((x) - GPIO_IRQ_START)
+
+#endif
+
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/hardware.h
@@ -0,0 +1,28 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/hardware.h
+ *
+ * This file contains the hardware definitions of the BCM2708 devices.
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+#include <asm/sizes.h>
+#include <mach/platform.h>
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/io.h
@@ -0,0 +1,27 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/io.h
+ *
+ * Copyright (C) 2003 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __ASM_ARM_ARCH_IO_H
+#define __ASM_ARM_ARCH_IO_H
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+#define __io(a) __typesafe_io(a)
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/irqs.h
@@ -0,0 +1,199 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/irqs.h
+ *
+ * Copyright (C) 2010 Broadcom
+ * Copyright (C) 2003 ARM Limited
+ * Copyright (C) 2000 Deep Blue Solutions Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _BCM2708_IRQS_H_
+#define _BCM2708_IRQS_H_
+
+#include <mach/platform.h>
+
+/*
+ * IRQ interrupts definitions are the same as the INT definitions
+ * held within platform.h
+ */
+#define IRQ_ARMCTRL_START 0
+#define IRQ_TIMER0 (IRQ_ARMCTRL_START + INTERRUPT_TIMER0)
+#define IRQ_TIMER1 (IRQ_ARMCTRL_START + INTERRUPT_TIMER1)
+#define IRQ_TIMER2 (IRQ_ARMCTRL_START + INTERRUPT_TIMER2)
+#define IRQ_TIMER3 (IRQ_ARMCTRL_START + INTERRUPT_TIMER3)
+#define IRQ_CODEC0 (IRQ_ARMCTRL_START + INTERRUPT_CODEC0)
+#define IRQ_CODEC1 (IRQ_ARMCTRL_START + INTERRUPT_CODEC1)
+#define IRQ_CODEC2 (IRQ_ARMCTRL_START + INTERRUPT_CODEC2)
+#define IRQ_JPEG (IRQ_ARMCTRL_START + INTERRUPT_JPEG)
+#define IRQ_ISP (IRQ_ARMCTRL_START + INTERRUPT_ISP)
+#define IRQ_USB (IRQ_ARMCTRL_START + INTERRUPT_USB)
+#define IRQ_3D (IRQ_ARMCTRL_START + INTERRUPT_3D)
+#define IRQ_TRANSPOSER (IRQ_ARMCTRL_START + INTERRUPT_TRANSPOSER)
+#define IRQ_MULTICORESYNC0 (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC0)
+#define IRQ_MULTICORESYNC1 (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC1)
+#define IRQ_MULTICORESYNC2 (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC2)
+#define IRQ_MULTICORESYNC3 (IRQ_ARMCTRL_START + INTERRUPT_MULTICORESYNC3)
+#define IRQ_DMA0 (IRQ_ARMCTRL_START + INTERRUPT_DMA0)
+#define IRQ_DMA1 (IRQ_ARMCTRL_START + INTERRUPT_DMA1)
+#define IRQ_DMA2 (IRQ_ARMCTRL_START + INTERRUPT_DMA2)
+#define IRQ_DMA3 (IRQ_ARMCTRL_START + INTERRUPT_DMA3)
+#define IRQ_DMA4 (IRQ_ARMCTRL_START + INTERRUPT_DMA4)
+#define IRQ_DMA5 (IRQ_ARMCTRL_START + INTERRUPT_DMA5)
+#define IRQ_DMA6 (IRQ_ARMCTRL_START + INTERRUPT_DMA6)
+#define IRQ_DMA7 (IRQ_ARMCTRL_START + INTERRUPT_DMA7)
+#define IRQ_DMA8 (IRQ_ARMCTRL_START + INTERRUPT_DMA8)
+#define IRQ_DMA9 (IRQ_ARMCTRL_START + INTERRUPT_DMA9)
+#define IRQ_DMA10 (IRQ_ARMCTRL_START + INTERRUPT_DMA10)
+#define IRQ_DMA11 (IRQ_ARMCTRL_START + INTERRUPT_DMA11)
+#define IRQ_DMA12 (IRQ_ARMCTRL_START + INTERRUPT_DMA12)
+#define IRQ_AUX (IRQ_ARMCTRL_START + INTERRUPT_AUX)
+#define IRQ_ARM (IRQ_ARMCTRL_START + INTERRUPT_ARM)
+#define IRQ_VPUDMA (IRQ_ARMCTRL_START + INTERRUPT_VPUDMA)
+#define IRQ_HOSTPORT (IRQ_ARMCTRL_START + INTERRUPT_HOSTPORT)
+#define IRQ_VIDEOSCALER (IRQ_ARMCTRL_START + INTERRUPT_VIDEOSCALER)
+#define IRQ_CCP2TX (IRQ_ARMCTRL_START + INTERRUPT_CCP2TX)
+#define IRQ_SDC (IRQ_ARMCTRL_START + INTERRUPT_SDC)
+#define IRQ_DSI0 (IRQ_ARMCTRL_START + INTERRUPT_DSI0)
+#define IRQ_AVE (IRQ_ARMCTRL_START + INTERRUPT_AVE)
+#define IRQ_CAM0 (IRQ_ARMCTRL_START + INTERRUPT_CAM0)
+#define IRQ_CAM1 (IRQ_ARMCTRL_START + INTERRUPT_CAM1)
+#define IRQ_HDMI0 (IRQ_ARMCTRL_START + INTERRUPT_HDMI0)
+#define IRQ_HDMI1 (IRQ_ARMCTRL_START + INTERRUPT_HDMI1)
+#define IRQ_PIXELVALVE1 (IRQ_ARMCTRL_START + INTERRUPT_PIXELVALVE1)
+#define IRQ_I2CSPISLV (IRQ_ARMCTRL_START + INTERRUPT_I2CSPISLV)
+#define IRQ_DSI1 (IRQ_ARMCTRL_START + INTERRUPT_DSI1)
+#define IRQ_PWA0 (IRQ_ARMCTRL_START + INTERRUPT_PWA0)
+#define IRQ_PWA1 (IRQ_ARMCTRL_START + INTERRUPT_PWA1)
+#define IRQ_CPR (IRQ_ARMCTRL_START + INTERRUPT_CPR)
+#define IRQ_SMI (IRQ_ARMCTRL_START + INTERRUPT_SMI)
+#define IRQ_GPIO0 (IRQ_ARMCTRL_START + INTERRUPT_GPIO0)
+#define IRQ_GPIO1 (IRQ_ARMCTRL_START + INTERRUPT_GPIO1)
+#define IRQ_GPIO2 (IRQ_ARMCTRL_START + INTERRUPT_GPIO2)
+#define IRQ_GPIO3 (IRQ_ARMCTRL_START + INTERRUPT_GPIO3)
+#define IRQ_I2C (IRQ_ARMCTRL_START + INTERRUPT_I2C)
+#define IRQ_SPI (IRQ_ARMCTRL_START + INTERRUPT_SPI)
+#define IRQ_I2SPCM (IRQ_ARMCTRL_START + INTERRUPT_I2SPCM)
+#define IRQ_SDIO (IRQ_ARMCTRL_START + INTERRUPT_SDIO)
+#define IRQ_UART (IRQ_ARMCTRL_START + INTERRUPT_UART)
+#define IRQ_SLIMBUS (IRQ_ARMCTRL_START + INTERRUPT_SLIMBUS)
+#define IRQ_VEC (IRQ_ARMCTRL_START + INTERRUPT_VEC)
+#define IRQ_CPG (IRQ_ARMCTRL_START + INTERRUPT_CPG)
+#define IRQ_RNG (IRQ_ARMCTRL_START + INTERRUPT_RNG)
+#define IRQ_ARASANSDIO (IRQ_ARMCTRL_START + INTERRUPT_ARASANSDIO)
+#define IRQ_AVSPMON (IRQ_ARMCTRL_START + INTERRUPT_AVSPMON)
+
+#define IRQ_ARM_TIMER (IRQ_ARMCTRL_START + INTERRUPT_ARM_TIMER)
+#define IRQ_ARM_MAILBOX (IRQ_ARMCTRL_START + INTERRUPT_ARM_MAILBOX)
+#define IRQ_ARM_DOORBELL_0 (IRQ_ARMCTRL_START + INTERRUPT_ARM_DOORBELL_0)
+#define IRQ_ARM_DOORBELL_1 (IRQ_ARMCTRL_START + INTERRUPT_ARM_DOORBELL_1)
+#define IRQ_VPU0_HALTED (IRQ_ARMCTRL_START + INTERRUPT_VPU0_HALTED)
+#define IRQ_VPU1_HALTED (IRQ_ARMCTRL_START + INTERRUPT_VPU1_HALTED)
+#define IRQ_ILLEGAL_TYPE0 (IRQ_ARMCTRL_START + INTERRUPT_ILLEGAL_TYPE0)
+#define IRQ_ILLEGAL_TYPE1 (IRQ_ARMCTRL_START + INTERRUPT_ILLEGAL_TYPE1)
+#define IRQ_PENDING1 (IRQ_ARMCTRL_START + INTERRUPT_PENDING1)
+#define IRQ_PENDING2 (IRQ_ARMCTRL_START + INTERRUPT_PENDING2)
+
+#define FIQ_START HARD_IRQS
+
+/*
+ * FIQ interrupts definitions are the same as the INT definitions.
+ */
+#define FIQ_TIMER0 (FIQ_START+INTERRUPT_TIMER0)
+#define FIQ_TIMER1 (FIQ_START+INTERRUPT_TIMER1)
+#define FIQ_TIMER2 (FIQ_START+INTERRUPT_TIMER2)
+#define FIQ_TIMER3 (FIQ_START+INTERRUPT_TIMER3)
+#define FIQ_CODEC0 (FIQ_START+INTERRUPT_CODEC0)
+#define FIQ_CODEC1 (FIQ_START+INTERRUPT_CODEC1)
+#define FIQ_CODEC2 (FIQ_START+INTERRUPT_CODEC2)
+#define FIQ_JPEG (FIQ_START+INTERRUPT_JPEG)
+#define FIQ_ISP (FIQ_START+INTERRUPT_ISP)
+#define FIQ_USB (FIQ_START+INTERRUPT_USB)
+#define FIQ_3D (FIQ_START+INTERRUPT_3D)
+#define FIQ_TRANSPOSER (FIQ_START+INTERRUPT_TRANSPOSER)
+#define FIQ_MULTICORESYNC0 (FIQ_START+INTERRUPT_MULTICORESYNC0)
+#define FIQ_MULTICORESYNC1 (FIQ_START+INTERRUPT_MULTICORESYNC1)
+#define FIQ_MULTICORESYNC2 (FIQ_START+INTERRUPT_MULTICORESYNC2)
+#define FIQ_MULTICORESYNC3 (FIQ_START+INTERRUPT_MULTICORESYNC3)
+#define FIQ_DMA0 (FIQ_START+INTERRUPT_DMA0)
+#define FIQ_DMA1 (FIQ_START+INTERRUPT_DMA1)
+#define FIQ_DMA2 (FIQ_START+INTERRUPT_DMA2)
+#define FIQ_DMA3 (FIQ_START+INTERRUPT_DMA3)
+#define FIQ_DMA4 (FIQ_START+INTERRUPT_DMA4)
+#define FIQ_DMA5 (FIQ_START+INTERRUPT_DMA5)
+#define FIQ_DMA6 (FIQ_START+INTERRUPT_DMA6)
+#define FIQ_DMA7 (FIQ_START+INTERRUPT_DMA7)
+#define FIQ_DMA8 (FIQ_START+INTERRUPT_DMA8)
+#define FIQ_DMA9 (FIQ_START+INTERRUPT_DMA9)
+#define FIQ_DMA10 (FIQ_START+INTERRUPT_DMA10)
+#define FIQ_DMA11 (FIQ_START+INTERRUPT_DMA11)
+#define FIQ_DMA12 (FIQ_START+INTERRUPT_DMA12)
+#define FIQ_AUX (FIQ_START+INTERRUPT_AUX)
+#define FIQ_ARM (FIQ_START+INTERRUPT_ARM)
+#define FIQ_VPUDMA (FIQ_START+INTERRUPT_VPUDMA)
+#define FIQ_HOSTPORT (FIQ_START+INTERRUPT_HOSTPORT)
+#define FIQ_VIDEOSCALER (FIQ_START+INTERRUPT_VIDEOSCALER)
+#define FIQ_CCP2TX (FIQ_START+INTERRUPT_CCP2TX)
+#define FIQ_SDC (FIQ_START+INTERRUPT_SDC)
+#define FIQ_DSI0 (FIQ_START+INTERRUPT_DSI0)
+#define FIQ_AVE (FIQ_START+INTERRUPT_AVE)
+#define FIQ_CAM0 (FIQ_START+INTERRUPT_CAM0)
+#define FIQ_CAM1 (FIQ_START+INTERRUPT_CAM1)
+#define FIQ_HDMI0 (FIQ_START+INTERRUPT_HDMI0)
+#define FIQ_HDMI1 (FIQ_START+INTERRUPT_HDMI1)
+#define FIQ_PIXELVALVE1 (FIQ_START+INTERRUPT_PIXELVALVE1)
+#define FIQ_I2CSPISLV (FIQ_START+INTERRUPT_I2CSPISLV)
+#define FIQ_DSI1 (FIQ_START+INTERRUPT_DSI1)
+#define FIQ_PWA0 (FIQ_START+INTERRUPT_PWA0)
+#define FIQ_PWA1 (FIQ_START+INTERRUPT_PWA1)
+#define FIQ_CPR (FIQ_START+INTERRUPT_CPR)
+#define FIQ_SMI (FIQ_START+INTERRUPT_SMI)
+#define FIQ_GPIO0 (FIQ_START+INTERRUPT_GPIO0)
+#define FIQ_GPIO1 (FIQ_START+INTERRUPT_GPIO1)
+#define FIQ_GPIO2 (FIQ_START+INTERRUPT_GPIO2)
+#define FIQ_GPIO3 (FIQ_START+INTERRUPT_GPIO3)
+#define FIQ_I2C (FIQ_START+INTERRUPT_I2C)
+#define FIQ_SPI (FIQ_START+INTERRUPT_SPI)
+#define FIQ_I2SPCM (FIQ_START+INTERRUPT_I2SPCM)
+#define FIQ_SDIO (FIQ_START+INTERRUPT_SDIO)
+#define FIQ_UART (FIQ_START+INTERRUPT_UART)
+#define FIQ_SLIMBUS (FIQ_START+INTERRUPT_SLIMBUS)
+#define FIQ_VEC (FIQ_START+INTERRUPT_VEC)
+#define FIQ_CPG (FIQ_START+INTERRUPT_CPG)
+#define FIQ_RNG (FIQ_START+INTERRUPT_RNG)
+#define FIQ_ARASANSDIO (FIQ_START+INTERRUPT_ARASANSDIO)
+#define FIQ_AVSPMON (FIQ_START+INTERRUPT_AVSPMON)
+
+#define FIQ_ARM_TIMER (FIQ_START+INTERRUPT_ARM_TIMER)
+#define FIQ_ARM_MAILBOX (FIQ_START+INTERRUPT_ARM_MAILBOX)
+#define FIQ_ARM_DOORBELL_0 (FIQ_START+INTERRUPT_ARM_DOORBELL_0)
+#define FIQ_ARM_DOORBELL_1 (FIQ_START+INTERRUPT_ARM_DOORBELL_1)
+#define FIQ_VPU0_HALTED (FIQ_START+INTERRUPT_VPU0_HALTED)
+#define FIQ_VPU1_HALTED (FIQ_START+INTERRUPT_VPU1_HALTED)
+#define FIQ_ILLEGAL_TYPE0 (FIQ_START+INTERRUPT_ILLEGAL_TYPE0)
+#define FIQ_ILLEGAL_TYPE1 (FIQ_START+INTERRUPT_ILLEGAL_TYPE1)
+#define FIQ_PENDING1 (FIQ_START+INTERRUPT_PENDING1)
+#define FIQ_PENDING2 (FIQ_START+INTERRUPT_PENDING2)
+
+#define GPIO_IRQ_START (HARD_IRQS + FIQ_IRQS)
+
+#define HARD_IRQS (64 + 21)
+#define FIQ_IRQS (64 + 21)
+#define GPIO_IRQS (32*5)
+
+#define NR_IRQS HARD_IRQS+FIQ_IRQS+GPIO_IRQS
+
+
+#endif /* _BCM2708_IRQS_H_ */
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/memory.h
@@ -0,0 +1,57 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/memory.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/* Memory overview:
+
+ [ARMcore] <--virtual addr-->
+ [ARMmmu] <--physical addr-->
+ [GERTmap] <--bus add-->
+ [VCperiph]
+
+*/
+
+/*
+ * Physical DRAM offset.
+ */
+#define PLAT_PHYS_OFFSET UL(0x00000000)
+#define VC_ARMMEM_OFFSET UL(0x00000000) /* offset in VC of ARM memory */
+
+#ifdef CONFIG_BCM2708_NOL2CACHE
+ #define _REAL_BUS_OFFSET UL(0xC0000000) /* don't use L1 or L2 caches */
+#else
+ #define _REAL_BUS_OFFSET UL(0x40000000) /* use L2 cache */
+#endif
+
+/* We're using the memory at 64M in the VideoCore for Linux - this adjustment
+ * will provide the offset into this area as well as setting the bits that
+ * stop the L1 and L2 cache from being used
+ *
+ * WARNING: this only works because the ARM is given memory at a fixed location
+ * (ARMMEM_OFFSET)
+ */
+#define BUS_OFFSET (VC_ARMMEM_OFFSET + _REAL_BUS_OFFSET)
+#define __virt_to_bus(x) ((x) + (BUS_OFFSET - PAGE_OFFSET))
+#define __bus_to_virt(x) ((x) - (BUS_OFFSET - PAGE_OFFSET))
+#define __pfn_to_bus(x) (__pfn_to_phys(x) + (BUS_OFFSET - PLAT_PHYS_OFFSET))
+#define __bus_to_pfn(x) __phys_to_pfn((x) - (BUS_OFFSET - PLAT_PHYS_OFFSET))
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/platform.h
@@ -0,0 +1,226 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/platform.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _BCM2708_PLATFORM_H
+#define _BCM2708_PLATFORM_H
+
+
+/* macros to get at IO space when running virtually */
+#define IO_ADDRESS(x) (((x) & 0x0fffffff) + (((x) >> 4) & 0x0f000000) + 0xf0000000)
+
+#define __io_address(n) IOMEM(IO_ADDRESS(n))
+
+
+/*
+ * SDRAM
+ */
+#define BCM2708_SDRAM_BASE 0x00000000
+
+/*
+ * Logic expansion modules
+ *
+ */
+
+
+/* ------------------------------------------------------------------------
+ * BCM2708 ARMCTRL Registers
+ * ------------------------------------------------------------------------
+ */
+
+#define HW_REGISTER_RW(addr) (addr)
+#define HW_REGISTER_RO(addr) (addr)
+
+#include "arm_control.h"
+#undef ARM_BASE
+
+/*
+ * Definitions and addresses for the ARM CONTROL logic
+ * This file is manually generated.
+ */
+
+#define BCM2708_PERI_BASE 0x20000000
+#define IC0_BASE (BCM2708_PERI_BASE + 0x2000)
+#define ST_BASE (BCM2708_PERI_BASE + 0x3000) /* System Timer */
+#define MPHI_BASE (BCM2708_PERI_BASE + 0x6000) /* Message -based Parallel Host Interface */
+#define DMA_BASE (BCM2708_PERI_BASE + 0x7000) /* DMA controller */
+#define ARM_BASE (BCM2708_PERI_BASE + 0xB000) /* BCM2708 ARM control block */
+#define PM_BASE (BCM2708_PERI_BASE + 0x100000) /* Power Management, Reset controller and Watchdog registers */
+#define RNG_BASE (BCM2708_PERI_BASE + 0x104000) /* Hardware RNG */
+#define GPIO_BASE (BCM2708_PERI_BASE + 0x200000) /* GPIO */
+#define UART0_BASE (BCM2708_PERI_BASE + 0x201000) /* Uart 0 */
+#define MMCI0_BASE (BCM2708_PERI_BASE + 0x202000) /* MMC interface */
+#define SPI0_BASE (BCM2708_PERI_BASE + 0x204000) /* SPI0 */
+#define BSC0_BASE (BCM2708_PERI_BASE + 0x205000) /* BSC0 I2C/TWI */
+#define UART1_BASE (BCM2708_PERI_BASE + 0x215000) /* Uart 1 */
+#define EMMC_BASE (BCM2708_PERI_BASE + 0x300000) /* eMMC interface */
+#define SMI_BASE (BCM2708_PERI_BASE + 0x600000) /* SMI */
+#define BSC1_BASE (BCM2708_PERI_BASE + 0x804000) /* BSC1 I2C/TWI */
+#define USB_BASE (BCM2708_PERI_BASE + 0x980000) /* DTC_OTG USB controller */
+#define MCORE_BASE (BCM2708_PERI_BASE + 0x0000) /* Fake frame buffer device (actually the multicore sync block*/
+
+#define ARMCTRL_BASE (ARM_BASE + 0x000)
+#define ARMCTRL_IC_BASE (ARM_BASE + 0x200) /* ARM interrupt controller */
+#define ARMCTRL_TIMER0_1_BASE (ARM_BASE + 0x400) /* Timer 0 and 1 */
+#define ARMCTRL_0_SBM_BASE (ARM_BASE + 0x800) /* User 0 (ARM)'s Semaphores Doorbells and Mailboxes */
+
+
+/*
+ * Interrupt assignments
+ */
+
+#define ARM_IRQ1_BASE 0
+#define INTERRUPT_TIMER0 (ARM_IRQ1_BASE + 0)
+#define INTERRUPT_TIMER1 (ARM_IRQ1_BASE + 1)
+#define INTERRUPT_TIMER2 (ARM_IRQ1_BASE + 2)
+#define INTERRUPT_TIMER3 (ARM_IRQ1_BASE + 3)
+#define INTERRUPT_CODEC0 (ARM_IRQ1_BASE + 4)
+#define INTERRUPT_CODEC1 (ARM_IRQ1_BASE + 5)
+#define INTERRUPT_CODEC2 (ARM_IRQ1_BASE + 6)
+#define INTERRUPT_VC_JPEG (ARM_IRQ1_BASE + 7)
+#define INTERRUPT_ISP (ARM_IRQ1_BASE + 8)
+#define INTERRUPT_VC_USB (ARM_IRQ1_BASE + 9)
+#define INTERRUPT_VC_3D (ARM_IRQ1_BASE + 10)
+#define INTERRUPT_TRANSPOSER (ARM_IRQ1_BASE + 11)
+#define INTERRUPT_MULTICORESYNC0 (ARM_IRQ1_BASE + 12)
+#define INTERRUPT_MULTICORESYNC1 (ARM_IRQ1_BASE + 13)
+#define INTERRUPT_MULTICORESYNC2 (ARM_IRQ1_BASE + 14)
+#define INTERRUPT_MULTICORESYNC3 (ARM_IRQ1_BASE + 15)
+#define INTERRUPT_DMA0 (ARM_IRQ1_BASE + 16)
+#define INTERRUPT_DMA1 (ARM_IRQ1_BASE + 17)
+#define INTERRUPT_VC_DMA2 (ARM_IRQ1_BASE + 18)
+#define INTERRUPT_VC_DMA3 (ARM_IRQ1_BASE + 19)
+#define INTERRUPT_DMA4 (ARM_IRQ1_BASE + 20)
+#define INTERRUPT_DMA5 (ARM_IRQ1_BASE + 21)
+#define INTERRUPT_DMA6 (ARM_IRQ1_BASE + 22)
+#define INTERRUPT_DMA7 (ARM_IRQ1_BASE + 23)
+#define INTERRUPT_DMA8 (ARM_IRQ1_BASE + 24)
+#define INTERRUPT_DMA9 (ARM_IRQ1_BASE + 25)
+#define INTERRUPT_DMA10 (ARM_IRQ1_BASE + 26)
+#define INTERRUPT_DMA11 (ARM_IRQ1_BASE + 27)
+#define INTERRUPT_DMA12 (ARM_IRQ1_BASE + 28)
+#define INTERRUPT_AUX (ARM_IRQ1_BASE + 29)
+#define INTERRUPT_ARM (ARM_IRQ1_BASE + 30)
+#define INTERRUPT_VPUDMA (ARM_IRQ1_BASE + 31)
+
+#define ARM_IRQ2_BASE 32
+#define INTERRUPT_HOSTPORT (ARM_IRQ2_BASE + 0)
+#define INTERRUPT_VIDEOSCALER (ARM_IRQ2_BASE + 1)
+#define INTERRUPT_CCP2TX (ARM_IRQ2_BASE + 2)
+#define INTERRUPT_SDC (ARM_IRQ2_BASE + 3)
+#define INTERRUPT_DSI0 (ARM_IRQ2_BASE + 4)
+#define INTERRUPT_AVE (ARM_IRQ2_BASE + 5)
+#define INTERRUPT_CAM0 (ARM_IRQ2_BASE + 6)
+#define INTERRUPT_CAM1 (ARM_IRQ2_BASE + 7)
+#define INTERRUPT_HDMI0 (ARM_IRQ2_BASE + 8)
+#define INTERRUPT_HDMI1 (ARM_IRQ2_BASE + 9)
+#define INTERRUPT_PIXELVALVE1 (ARM_IRQ2_BASE + 10)
+#define INTERRUPT_I2CSPISLV (ARM_IRQ2_BASE + 11)
+#define INTERRUPT_DSI1 (ARM_IRQ2_BASE + 12)
+#define INTERRUPT_PWA0 (ARM_IRQ2_BASE + 13)
+#define INTERRUPT_PWA1 (ARM_IRQ2_BASE + 14)
+#define INTERRUPT_CPR (ARM_IRQ2_BASE + 15)
+#define INTERRUPT_SMI (ARM_IRQ2_BASE + 16)
+#define INTERRUPT_GPIO0 (ARM_IRQ2_BASE + 17)
+#define INTERRUPT_GPIO1 (ARM_IRQ2_BASE + 18)
+#define INTERRUPT_GPIO2 (ARM_IRQ2_BASE + 19)
+#define INTERRUPT_GPIO3 (ARM_IRQ2_BASE + 20)
+#define INTERRUPT_VC_I2C (ARM_IRQ2_BASE + 21)
+#define INTERRUPT_VC_SPI (ARM_IRQ2_BASE + 22)
+#define INTERRUPT_VC_I2SPCM (ARM_IRQ2_BASE + 23)
+#define INTERRUPT_VC_SDIO (ARM_IRQ2_BASE + 24)
+#define INTERRUPT_VC_UART (ARM_IRQ2_BASE + 25)
+#define INTERRUPT_SLIMBUS (ARM_IRQ2_BASE + 26)
+#define INTERRUPT_VEC (ARM_IRQ2_BASE + 27)
+#define INTERRUPT_CPG (ARM_IRQ2_BASE + 28)
+#define INTERRUPT_RNG (ARM_IRQ2_BASE + 29)
+#define INTERRUPT_VC_ARASANSDIO (ARM_IRQ2_BASE + 30)
+#define INTERRUPT_AVSPMON (ARM_IRQ2_BASE + 31)
+
+#define ARM_IRQ0_BASE 64
+#define INTERRUPT_ARM_TIMER (ARM_IRQ0_BASE + 0)
+#define INTERRUPT_ARM_MAILBOX (ARM_IRQ0_BASE + 1)
+#define INTERRUPT_ARM_DOORBELL_0 (ARM_IRQ0_BASE + 2)
+#define INTERRUPT_ARM_DOORBELL_1 (ARM_IRQ0_BASE + 3)
+#define INTERRUPT_VPU0_HALTED (ARM_IRQ0_BASE + 4)
+#define INTERRUPT_VPU1_HALTED (ARM_IRQ0_BASE + 5)
+#define INTERRUPT_ILLEGAL_TYPE0 (ARM_IRQ0_BASE + 6)
+#define INTERRUPT_ILLEGAL_TYPE1 (ARM_IRQ0_BASE + 7)
+#define INTERRUPT_PENDING1 (ARM_IRQ0_BASE + 8)
+#define INTERRUPT_PENDING2 (ARM_IRQ0_BASE + 9)
+#define INTERRUPT_JPEG (ARM_IRQ0_BASE + 10)
+#define INTERRUPT_USB (ARM_IRQ0_BASE + 11)
+#define INTERRUPT_3D (ARM_IRQ0_BASE + 12)
+#define INTERRUPT_DMA2 (ARM_IRQ0_BASE + 13)
+#define INTERRUPT_DMA3 (ARM_IRQ0_BASE + 14)
+#define INTERRUPT_I2C (ARM_IRQ0_BASE + 15)
+#define INTERRUPT_SPI (ARM_IRQ0_BASE + 16)
+#define INTERRUPT_I2SPCM (ARM_IRQ0_BASE + 17)
+#define INTERRUPT_SDIO (ARM_IRQ0_BASE + 18)
+#define INTERRUPT_UART (ARM_IRQ0_BASE + 19)
+#define INTERRUPT_ARASANSDIO (ARM_IRQ0_BASE + 20)
+
+#define MAXIRQNUM (32 + 32 + 20)
+#define MAXFIQNUM (32 + 32 + 20)
+
+#define MAX_TIMER 2
+#define MAX_PERIOD 699050
+#define TICKS_PER_uSEC 1
+
+/*
+ * These are useconds NOT ticks.
+ *
+ */
+#define mSEC_1 1000
+#define mSEC_5 (mSEC_1 * 5)
+#define mSEC_10 (mSEC_1 * 10)
+#define mSEC_25 (mSEC_1 * 25)
+#define SEC_1 (mSEC_1 * 1000)
+
+/*
+ * Watchdog
+ */
+#define PM_RSTC (PM_BASE+0x1c)
+#define PM_RSTS (PM_BASE+0x20)
+#define PM_WDOG (PM_BASE+0x24)
+
+#define PM_WDOG_RESET 0000000000
+#define PM_PASSWORD 0x5a000000
+#define PM_WDOG_TIME_SET 0x000fffff
+#define PM_RSTC_WRCFG_CLR 0xffffffcf
+#define PM_RSTC_WRCFG_SET 0x00000030
+#define PM_RSTC_WRCFG_FULL_RESET 0x00000020
+#define PM_RSTC_RESET 0x00000102
+
+#define PM_RSTS_HADPOR_SET 0x00001000
+#define PM_RSTS_HADSRH_SET 0x00000400
+#define PM_RSTS_HADSRF_SET 0x00000200
+#define PM_RSTS_HADSRQ_SET 0x00000100
+#define PM_RSTS_HADWRH_SET 0x00000040
+#define PM_RSTS_HADWRF_SET 0x00000020
+#define PM_RSTS_HADWRQ_SET 0x00000010
+#define PM_RSTS_HADDRH_SET 0x00000004
+#define PM_RSTS_HADDRF_SET 0x00000002
+#define PM_RSTS_HADDRQ_SET 0x00000001
+
+#define UART0_CLOCK 3000000
+
+#endif
+
+/* END */
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/power.h
@@ -0,0 +1,26 @@
+/*
+ * linux/arch/arm/mach-bcm2708/power.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This device provides a shared mechanism for controlling the power to
+ * VideoCore subsystems.
+ */
+
+#ifndef _MACH_BCM2708_POWER_H
+#define _MACH_BCM2708_POWER_H
+
+#include <linux/types.h>
+#include <mach/arm_power.h>
+
+typedef unsigned int BCM_POWER_HANDLE_T;
+
+extern int bcm_power_open(BCM_POWER_HANDLE_T *handle);
+extern int bcm_power_request(BCM_POWER_HANDLE_T handle, uint32_t request);
+extern int bcm_power_close(BCM_POWER_HANDLE_T handle);
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/system.h
@@ -0,0 +1,38 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/system.h
+ *
+ * Copyright (C) 2010 Broadcom
+ * Copyright (C) 2003 ARM Limited
+ * Copyright (C) 2000 Deep Blue Solutions Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+
+#include <linux/io.h>
+#include <mach/hardware.h>
+#include <mach/platform.h>
+
+static inline void arch_idle(void)
+{
+ /*
+ * This should do all the clock switching
+ * and wait for interrupt tricks
+ */
+ cpu_do_idle();
+}
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/timex.h
@@ -0,0 +1,23 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/timex.h
+ *
+ * BCM2708 sysem clock frequency
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#define CLOCK_TICK_RATE (1000000)
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/uncompress.h
@@ -0,0 +1,85 @@
+/*
+ * arch/arm/mach-bcn2708/include/mach/uncompress.h
+ *
+ * Copyright (C) 2010 Broadcom
+ * Copyright (C) 2003 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/io.h>
+#include <linux/amba/serial.h>
+#include <mach/hardware.h>
+
+#define UART_BAUD 115200
+
+#define BCM2708_UART_DR __io(UART0_BASE + UART01x_DR)
+#define BCM2708_UART_FR __io(UART0_BASE + UART01x_FR)
+#define BCM2708_UART_IBRD __io(UART0_BASE + UART011_IBRD)
+#define BCM2708_UART_FBRD __io(UART0_BASE + UART011_FBRD)
+#define BCM2708_UART_LCRH __io(UART0_BASE + UART011_LCRH)
+#define BCM2708_UART_CR __io(UART0_BASE + UART011_CR)
+
+/*
+ * This does not append a newline
+ */
+static inline void putc(int c)
+{
+ while (__raw_readl(BCM2708_UART_FR) & UART01x_FR_TXFF)
+ barrier();
+
+ __raw_writel(c, BCM2708_UART_DR);
+}
+
+static inline void flush(void)
+{
+ int fr;
+
+ do {
+ fr = __raw_readl(BCM2708_UART_FR);
+ barrier();
+ } while ((fr & (UART011_FR_TXFE | UART01x_FR_BUSY)) != UART011_FR_TXFE);
+}
+
+static inline void arch_decomp_setup(void)
+{
+ int temp, div, rem, frac;
+
+ temp = 16 * UART_BAUD;
+ div = UART0_CLOCK / temp;
+ rem = UART0_CLOCK % temp;
+ temp = (8 * rem) / UART_BAUD;
+ frac = (temp >> 1) + (temp & 1);
+
+ /* Make sure the UART is disabled before we start */
+ __raw_writel(0, BCM2708_UART_CR);
+
+ /* Set the baud rate */
+ __raw_writel(div, BCM2708_UART_IBRD);
+ __raw_writel(frac, BCM2708_UART_FBRD);
+
+ /* Set the UART to 8n1, FIFO enabled */
+ __raw_writel(UART01x_LCRH_WLEN_8 | UART01x_LCRH_FEN, BCM2708_UART_LCRH);
+
+ /* Enable the UART */
+ __raw_writel(UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_RXE,
+ BCM2708_UART_CR);
+}
+
+/*
+ * nothing to do
+ */
+#define arch_decomp_wdog()
+
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/vcio.h
@@ -0,0 +1,141 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/vcio.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef _MACH_BCM2708_VCIO_H
+#define _MACH_BCM2708_VCIO_H
+
+/* Routines to handle I/O via the VideoCore "ARM control" registers
+ * (semaphores, doorbells, mailboxes)
+ */
+
+#define BCM_VCIO_DRIVER_NAME "bcm2708_vcio"
+
+/* Constants shared with the ARM identifying separate mailbox channels */
+#define MBOX_CHAN_POWER 0 /* for use by the power management interface */
+#define MBOX_CHAN_FB 1 /* for use by the frame buffer */
+#define MBOX_CHAN_VCHIQ 3 /* for use by the VCHIQ interface */
+#define MBOX_CHAN_PROPERTY 8 /* for use by the property channel */
+#define MBOX_CHAN_COUNT 9
+
+/* Mailbox property tags */
+enum {
+ VCMSG_PROPERTY_END = 0x00000000,
+ VCMSG_GET_FIRMWARE_REVISION = 0x00000001,
+ VCMSG_GET_BOARD_MODEL = 0x00010001,
+ VCMSG_GET_BOARD_REVISION = 0x00020002,
+ VCMSG_GET_BOARD_MAC_ADDRESS = 0x00020003,
+ VCMSG_GET_BOARD_SERIAL = 0x00020004,
+ VCMSG_GET_ARM_MEMORY = 0x00020005,
+ VCMSG_GET_VC_MEMORY = 0x00020006,
+ VCMSG_GET_CLOCKS = 0x00020007,
+ VCMSG_GET_COMMAND_LINE = 0x00050001,
+ VCMSG_GET_DMA_CHANNELS = 0x00060001,
+ VCMSG_GET_POWER_STATE = 0x00020001,
+ VCMSG_GET_TIMING = 0x00020002,
+ VCMSG_SET_POWER_STATE = 0x00028001,
+ VCMSG_GET_CLOCK_STATE = 0x00030001,
+ VCMSG_SET_CLOCK_STATE = 0x00038001,
+ VCMSG_GET_CLOCK_RATE = 0x00030002,
+ VCMSG_SET_CLOCK_RATE = 0x00038002,
+ VCMSG_GET_VOLTAGE = 0x00030003,
+ VCMSG_SET_VOLTAGE = 0x00038003,
+ VCMSG_GET_MAX_CLOCK = 0x00030004,
+ VCMSG_GET_MAX_VOLTAGE = 0x00030005,
+ VCMSG_GET_TEMPERATURE = 0x00030006,
+ VCMSG_GET_MIN_CLOCK = 0x00030007,
+ VCMSG_GET_MIN_VOLTAGE = 0x00030008,
+ VCMSG_GET_TURBO = 0x00030009,
+ VCMSG_SET_TURBO = 0x00038009,
+ VCMSG_SET_ALLOCATE_BUFFER = 0x00040001,
+ VCMSG_SET_RELEASE_BUFFER = 0x00048001,
+ VCMSG_SET_BLANK_SCREEN = 0x00040002,
+ VCMSG_TST_BLANK_SCREEN = 0x00044002,
+ VCMSG_GET_PHYSICAL_WIDTH_HEIGHT = 0x00040003,
+ VCMSG_TST_PHYSICAL_WIDTH_HEIGHT = 0x00044003,
+ VCMSG_SET_PHYSICAL_WIDTH_HEIGHT = 0x00048003,
+ VCMSG_GET_VIRTUAL_WIDTH_HEIGHT = 0x00040004,
+ VCMSG_TST_VIRTUAL_WIDTH_HEIGHT = 0x00044004,
+ VCMSG_SET_VIRTUAL_WIDTH_HEIGHT = 0x00048004,
+ VCMSG_GET_DEPTH = 0x00040005,
+ VCMSG_TST_DEPTH = 0x00044005,
+ VCMSG_SET_DEPTH = 0x00048005,
+ VCMSG_GET_PIXEL_ORDER = 0x00040006,
+ VCMSG_TST_PIXEL_ORDER = 0x00044006,
+ VCMSG_SET_PIXEL_ORDER = 0x00048006,
+ VCMSG_GET_ALPHA_MODE = 0x00040007,
+ VCMSG_TST_ALPHA_MODE = 0x00044007,
+ VCMSG_SET_ALPHA_MODE = 0x00048007,
+ VCMSG_GET_PITCH = 0x00040008,
+ VCMSG_TST_PITCH = 0x00044008,
+ VCMSG_SET_PITCH = 0x00048008,
+ VCMSG_GET_VIRTUAL_OFFSET = 0x00040009,
+ VCMSG_TST_VIRTUAL_OFFSET = 0x00044009,
+ VCMSG_SET_VIRTUAL_OFFSET = 0x00048009,
+ VCMSG_GET_OVERSCAN = 0x0004000a,
+ VCMSG_TST_OVERSCAN = 0x0004400a,
+ VCMSG_SET_OVERSCAN = 0x0004800a,
+ VCMSG_GET_PALETTE = 0x0004000b,
+ VCMSG_TST_PALETTE = 0x0004400b,
+ VCMSG_SET_PALETTE = 0x0004800b,
+ VCMSG_GET_LAYER = 0x0004000c,
+ VCMSG_TST_LAYER = 0x0004400c,
+ VCMSG_SET_LAYER = 0x0004800c,
+ VCMSG_GET_TRANSFORM = 0x0004000d,
+ VCMSG_TST_TRANSFORM = 0x0004400d,
+ VCMSG_SET_TRANSFORM = 0x0004800d,
+};
+
+extern int /*rc*/ bcm_mailbox_read(unsigned chan, uint32_t *data28);
+extern int /*rc*/ bcm_mailbox_write(unsigned chan, uint32_t data28);
+extern int /*rc*/ bcm_mailbox_property(void *data, int size);
+
+#include <linux/ioctl.h>
+
+/*
+ * The major device number. We can't rely on dynamic
+ * registration any more, because ioctls need to know
+ * it.
+ */
+#define MAJOR_NUM 100
+
+/*
+ * Set the message of the device driver
+ */
+#define IOCTL_MBOX_PROPERTY _IOWR(MAJOR_NUM, 0, char *)
+/*
+ * _IOWR means that we're creating an ioctl command
+ * number for passing information from a user process
+ * to the kernel module and from the kernel module to user process
+ *
+ * The first arguments, MAJOR_NUM, is the major device
+ * number we're using.
+ *
+ * The second argument is the number of the command
+ * (there could be several with different meanings).
+ *
+ * The third argument is the type we want to get from
+ * the process to the kernel.
+ */
+
+/*
+ * The name of the device file
+ */
+#define DEVICE_FILE_NAME "char_dev"
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/vc_mem.h
@@ -0,0 +1,36 @@
+/*****************************************************************************
+* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+#if !defined( VC_MEM_H )
+#define VC_MEM_H
+
+#include <linux/ioctl.h>
+
+#define VC_MEM_IOC_MAGIC 'v'
+
+#define VC_MEM_IOC_MEM_PHYS_ADDR _IOR( VC_MEM_IOC_MAGIC, 0, unsigned long )
+#define VC_MEM_IOC_MEM_SIZE _IOR( VC_MEM_IOC_MAGIC, 1, unsigned int )
+#define VC_MEM_IOC_MEM_BASE _IOR( VC_MEM_IOC_MAGIC, 2, unsigned int )
+#define VC_MEM_IOC_MEM_LOAD _IOR( VC_MEM_IOC_MAGIC, 3, unsigned int )
+
+#if defined( __KERNEL__ )
+#define VC_MEM_TO_ARM_ADDR_MASK 0x3FFFFFFF
+
+extern unsigned long mm_vc_mem_phys_addr;
+extern unsigned int mm_vc_mem_size;
+extern int vc_mem_get_current_size( void );
+#endif
+
+#endif /* VC_MEM_H */
+
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/vc_support.h
@@ -0,0 +1,69 @@
+#ifndef _VC_SUPPORT_H_
+#define _VC_SUPPORT_H_
+
+/*
+ * vc_support.h
+ *
+ * Created on: 25 Nov 2012
+ * Author: Simon
+ */
+
+enum {
+/*
+ If a MEM_HANDLE_T is discardable, the memory manager may resize it to size
+ 0 at any time when it is not locked or retained.
+ */
+ MEM_FLAG_DISCARDABLE = 1 << 0,
+
+ /*
+ If a MEM_HANDLE_T is allocating (or normal), its block of memory will be
+ accessed in an allocating fashion through the cache.
+ */
+ MEM_FLAG_NORMAL = 0 << 2,
+ MEM_FLAG_ALLOCATING = MEM_FLAG_NORMAL,
+
+ /*
+ If a MEM_HANDLE_T is direct, its block of memory will be accessed
+ directly, bypassing the cache.
+ */
+ MEM_FLAG_DIRECT = 1 << 2,
+
+ /*
+ If a MEM_HANDLE_T is coherent, its block of memory will be accessed in a
+ non-allocating fashion through the cache.
+ */
+ MEM_FLAG_COHERENT = 2 << 2,
+
+ /*
+ If a MEM_HANDLE_T is L1-nonallocating, its block of memory will be accessed by
+ the VPU in a fashion which is allocating in L2, but only coherent in L1.
+ */
+ MEM_FLAG_L1_NONALLOCATING = (MEM_FLAG_DIRECT | MEM_FLAG_COHERENT),
+
+ /*
+ If a MEM_HANDLE_T is zero'd, its contents are set to 0 rather than
+ MEM_HANDLE_INVALID on allocation and resize up.
+ */
+ MEM_FLAG_ZERO = 1 << 4,
+
+ /*
+ If a MEM_HANDLE_T is uninitialised, it will not be reset to a defined value
+ (either zero, or all 1's) on allocation.
+ */
+ MEM_FLAG_NO_INIT = 1 << 5,
+
+ /*
+ Hints.
+ */
+ MEM_FLAG_HINT_PERMALOCK = 1 << 6, /* Likely to be locked for long periods of time. */
+};
+
+unsigned int AllocateVcMemory(unsigned int *pHandle, unsigned int size, unsigned int alignment, unsigned int flags);
+unsigned int ReleaseVcMemory(unsigned int handle);
+unsigned int LockVcMemory(unsigned int *pBusAddress, unsigned int handle);
+unsigned int UnlockVcMemory(unsigned int handle);
+
+unsigned int ExecuteVcCode(unsigned int code,
+ unsigned int r0, unsigned int r1, unsigned int r2, unsigned int r3, unsigned int r4, unsigned int r5);
+
+#endif
--- /dev/null
+++ b/arch/arm/mach-bcm2708/include/mach/vmalloc.h
@@ -0,0 +1,20 @@
+/*
+ * arch/arm/mach-bcm2708/include/mach/vmalloc.h
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#define VMALLOC_END (0xe8000000)
--- /dev/null
+++ b/arch/arm/mach-bcm2708/Kconfig
@@ -0,0 +1,48 @@
+menu "Broadcom BCM2708 Implementations"
+ depends on ARCH_BCM2708
+
+config MACH_BCM2708
+ bool "Broadcom BCM2708 Development Platform"
+ select NEED_MACH_MEMORY_H
+ select NEED_MACH_IO_H
+ select CPU_V6
+ help
+ Include support for the Broadcom(R) BCM2708 platform.
+
+config BCM2708_GPIO
+ bool "BCM2708 gpio support"
+ depends on MACH_BCM2708
+ select ARCH_REQUIRE_GPIOLIB
+ default y
+ help
+ Include support for the Broadcom(R) BCM2708 gpio.
+
+config BCM2708_VCMEM
+ bool "Videocore Memory"
+ depends on MACH_BCM2708
+ default y
+ help
+ Helper for videocore memory access and total size allocation.
+
+config BCM2708_NOL2CACHE
+ bool "Videocore L2 cache disable"
+ depends on MACH_BCM2708
+ default n
+ help
+ Do not allow ARM to use GPU's L2 cache. Requires disable_l2cache in config.txt.
+
+config BCM2708_DMAER
+ tristate "BCM2708 DMA helper"
+ depends on MACH_BCM2708
+ default n
+ help
+ Enable DMA helper for accelerating X composition
+
+config BCM2708_SPIDEV
+ bool "Bind spidev to SPI0 master"
+ depends on MACH_BCM2708
+ depends on SPI
+ default y
+ help
+ Binds spidev driver to the SPI0 master
+endmenu
--- /dev/null
+++ b/arch/arm/mach-bcm2708/Makefile
@@ -0,0 +1,11 @@
+#
+# Makefile for the linux kernel.
+#
+
+obj-$(CONFIG_MACH_BCM2708) += clock.o bcm2708.o armctrl.o vcio.o power.o dma.o
+obj-$(CONFIG_BCM2708_GPIO) += bcm2708_gpio.o
+obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o
+
+obj-$(CONFIG_BCM2708_DMAER) += dmaer_master.o
+dmaer_master-objs := dmaer.o vc_support.o
+
--- /dev/null
+++ b/arch/arm/mach-bcm2708/Makefile.boot
@@ -0,0 +1,3 @@
+ zreladdr-y := 0x00008000
+params_phys-y := 0x00000100
+initrd_phys-y := 0x00800000
--- /dev/null
+++ b/arch/arm/mach-bcm2708/power.c
@@ -0,0 +1,194 @@
+/*
+ * linux/arch/arm/mach-bcm2708/power.c
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This device provides a shared mechanism for controlling the power to
+ * VideoCore subsystems.
+ */
+
+#include <linux/module.h>
+#include <linux/semaphore.h>
+#include <linux/bug.h>
+#include <mach/power.h>
+#include <mach/vcio.h>
+#include <mach/arm_power.h>
+
+#define DRIVER_NAME "bcm2708_power"
+
+#define BCM_POWER_MAXCLIENTS 4
+#define BCM_POWER_NOCLIENT (1<<31)
+
+/* Some drivers expect there devices to be permanently powered */
+#define BCM_POWER_ALWAYS_ON (BCM_POWER_USB)
+
+#if 1
+#define DPRINTK printk
+#else
+#define DPRINTK if (0) printk
+#endif
+
+struct state_struct {
+ uint32_t global_request;
+ uint32_t client_request[BCM_POWER_MAXCLIENTS];
+ struct semaphore client_mutex;
+ struct semaphore mutex;
+} g_state;
+
+int bcm_power_open(BCM_POWER_HANDLE_T *handle)
+{
+ BCM_POWER_HANDLE_T i;
+ int ret = -EBUSY;
+
+ down(&g_state.client_mutex);
+
+ for (i = 0; i < BCM_POWER_MAXCLIENTS; i++) {
+ if (g_state.client_request[i] == BCM_POWER_NOCLIENT) {
+ g_state.client_request[i] = BCM_POWER_NONE;
+ *handle = i;
+ ret = 0;
+ break;
+ }
+ }
+
+ up(&g_state.client_mutex);
+
+ DPRINTK("bcm_power_open() -> %d\n", *handle);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(bcm_power_open);
+
+int bcm_power_request(BCM_POWER_HANDLE_T handle, uint32_t request)
+{
+ int rc = 0;
+
+ DPRINTK("bcm_power_request(%d, %x)\n", handle, request);
+
+ if ((handle < BCM_POWER_MAXCLIENTS) &&
+ (g_state.client_request[handle] != BCM_POWER_NOCLIENT)) {
+ if (down_interruptible(&g_state.mutex) != 0) {
+ DPRINTK("bcm_power_request -> interrupted\n");
+ return -EINTR;
+ }
+
+ if (request != g_state.client_request[handle]) {
+ uint32_t others_request = 0;
+ uint32_t global_request;
+ BCM_POWER_HANDLE_T i;
+
+ for (i = 0; i < BCM_POWER_MAXCLIENTS; i++) {
+ if (i != handle)
+ others_request |=
+ g_state.client_request[i];
+ }
+ others_request &= ~BCM_POWER_NOCLIENT;
+
+ global_request = request | others_request;
+ if (global_request != g_state.global_request) {
+ uint32_t actual;
+
+ /* Send a request to VideoCore */
+ bcm_mailbox_write(MBOX_CHAN_POWER,
+ global_request << 4);
+
+ /* Wait for a response during power-up */
+ if (global_request & ~g_state.global_request) {
+ rc = bcm_mailbox_read(MBOX_CHAN_POWER,
+ &actual);
+ DPRINTK
+ ("bcm_mailbox_read -> %08x, %d\n",
+ actual, rc);
+ actual >>= 4;
+ } else {
+ rc = 0;
+ actual = global_request;
+ }
+
+ if (rc == 0) {
+ if (actual != global_request) {
+ printk(KERN_ERR
+ "%s: prev global %x, new global %x, actual %x, request %x, others_request %x\n",
+ __func__,
+ g_state.global_request,
+ global_request, actual, request, others_request);
+ /* A failure */
+ BUG_ON((others_request & actual)
+ != others_request);
+ request &= actual;
+ rc = -EIO;
+ }
+
+ g_state.global_request = actual;
+ g_state.client_request[handle] =
+ request;
+ }
+ }
+ }
+ up(&g_state.mutex);
+ } else {
+ rc = -EINVAL;
+ }
+ DPRINTK("bcm_power_request -> %d\n", rc);
+ return rc;
+}
+EXPORT_SYMBOL_GPL(bcm_power_request);
+
+int bcm_power_close(BCM_POWER_HANDLE_T handle)
+{
+ int rc;
+
+ DPRINTK("bcm_power_close(%d)\n", handle);
+
+ rc = bcm_power_request(handle, BCM_POWER_NONE);
+ if (rc == 0)
+ g_state.client_request[handle] = BCM_POWER_NOCLIENT;
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(bcm_power_close);
+
+static int __init bcm_power_init(void)
+{
+#if defined(BCM_POWER_ALWAYS_ON)
+ BCM_POWER_HANDLE_T always_on_handle;
+#endif
+ int rc = 0;
+ int i;
+
+ printk(KERN_INFO "bcm_power: Broadcom power driver\n");
+ bcm_mailbox_write(MBOX_CHAN_POWER, 0);
+
+ for (i = 0; i < BCM_POWER_MAXCLIENTS; i++)
+ g_state.client_request[i] = BCM_POWER_NOCLIENT;
+
+ sema_init(&g_state.client_mutex, 1);
+ sema_init(&g_state.mutex, 1);
+
+ g_state.global_request = 0;
+
+#if defined(BCM_POWER_ALWAYS_ON)
+ if (BCM_POWER_ALWAYS_ON) {
+ bcm_power_open(&always_on_handle);
+ bcm_power_request(always_on_handle, BCM_POWER_ALWAYS_ON);
+ }
+#endif
+
+ return rc;
+}
+
+static void __exit bcm_power_exit(void)
+{
+ bcm_mailbox_write(MBOX_CHAN_POWER, 0);
+}
+
+arch_initcall(bcm_power_init); /* Initialize early */
+module_exit(bcm_power_exit);
+
+MODULE_AUTHOR("Phil Elwell");
+MODULE_DESCRIPTION("Interface to BCM2708 power management");
+MODULE_LICENSE("GPL");
--- /dev/null
+++ b/arch/arm/mach-bcm2708/vcio.c
@@ -0,0 +1,474 @@
+/*
+ * linux/arch/arm/mach-bcm2708/vcio.c
+ *
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This device provides a shared mechanism for writing to the mailboxes,
+ * semaphores, doorbells etc. that are shared between the ARM and the
+ * VideoCore processor
+ */
+
+#if defined(CONFIG_SERIAL_BCM_MBOX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/console.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/errno.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/sysrq.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <linux/io.h>
+
+#include <mach/vcio.h>
+#include <mach/platform.h>
+
+#include <asm/uaccess.h>
+
+
+#define DRIVER_NAME BCM_VCIO_DRIVER_NAME
+
+/* ----------------------------------------------------------------------
+ * Mailbox
+ * -------------------------------------------------------------------- */
+
+/* offsets from a mail box base address */
+#define MAIL_WRT 0x00 /* write - and next 4 words */
+#define MAIL_RD 0x00 /* read - and next 4 words */
+#define MAIL_POL 0x10 /* read without popping the fifo */
+#define MAIL_SND 0x14 /* sender ID (bottom two bits) */
+#define MAIL_STA 0x18 /* status */
+#define MAIL_CNF 0x1C /* configuration */
+
+#define MBOX_MSG(chan, data28) (((data28) & ~0xf) | ((chan) & 0xf))
+#define MBOX_MSG_LSB(chan, data28) (((data28) << 4) | ((chan) & 0xf))
+#define MBOX_CHAN(msg) ((msg) & 0xf)
+#define MBOX_DATA28(msg) ((msg) & ~0xf)
+#define MBOX_DATA28_LSB(msg) (((uint32_t)msg) >> 4)
+
+#define MBOX_MAGIC 0xd0d0c0de
+
+struct vc_mailbox {
+ struct device *dev; /* parent device */
+ void __iomem *status;
+ void __iomem *config;
+ void __iomem *read;
+ void __iomem *write;
+ uint32_t msg[MBOX_CHAN_COUNT];
+ struct semaphore sema[MBOX_CHAN_COUNT];
+ uint32_t magic;
+};
+
+static void mbox_init(struct vc_mailbox *mbox_out, struct device *dev,
+ uint32_t addr_mbox)
+{
+ int i;
+
+ mbox_out->dev = dev;
+ mbox_out->status = __io_address(addr_mbox + MAIL_STA);
+ mbox_out->config = __io_address(addr_mbox + MAIL_CNF);
+ mbox_out->read = __io_address(addr_mbox + MAIL_RD);
+ /* Write to the other mailbox */
+ mbox_out->write =
+ __io_address((addr_mbox ^ ARM_0_MAIL0_WRT ^ ARM_0_MAIL1_WRT) +
+ MAIL_WRT);
+
+ for (i = 0; i < MBOX_CHAN_COUNT; i++) {
+ mbox_out->msg[i] = 0;
+ sema_init(&mbox_out->sema[i], 0);
+ }
+
+ /* Enable the interrupt on data reception */
+ writel(ARM_MC_IHAVEDATAIRQEN, mbox_out->config);
+
+ mbox_out->magic = MBOX_MAGIC;
+}
+
+static int mbox_write(struct vc_mailbox *mbox, unsigned chan, uint32_t data28)
+{
+ int rc;
+
+ if (mbox->magic != MBOX_MAGIC)
+ rc = -EINVAL;
+ else {
+ /* wait for the mailbox FIFO to have some space in it */
+ while (0 != (readl(mbox->status) & ARM_MS_FULL))
+ cpu_relax();
+
+ writel(MBOX_MSG(chan, data28), mbox->write);
+ rc = 0;
+ }
+ return rc;
+}
+
+static int mbox_read(struct vc_mailbox *mbox, unsigned chan, uint32_t *data28)
+{
+ int rc;
+
+ if (mbox->magic != MBOX_MAGIC)
+ rc = -EINVAL;
+ else {
+ down(&mbox->sema[chan]);
+ *data28 = MBOX_DATA28(mbox->msg[chan]);
+ mbox->msg[chan] = 0;
+ rc = 0;
+ }
+ return rc;
+}
+
+static irqreturn_t mbox_irq(int irq, void *dev_id)
+{
+ /* wait for the mailbox FIFO to have some data in it */
+ struct vc_mailbox *mbox = (struct vc_mailbox *) dev_id;
+ int status = readl(mbox->status);
+ int ret = IRQ_NONE;
+
+ while (!(status & ARM_MS_EMPTY)) {
+ uint32_t msg = readl(mbox->read);
+ int chan = MBOX_CHAN(msg);
+ if (chan < MBOX_CHAN_COUNT) {
+ if (mbox->msg[chan]) {
+ /* Overflow */
+ printk(KERN_ERR DRIVER_NAME
+ ": mbox chan %d overflow - drop %08x\n",
+ chan, msg);
+ } else {
+ mbox->msg[chan] = (msg | 0xf);
+ up(&mbox->sema[chan]);
+ }
+ } else {
+ printk(KERN_ERR DRIVER_NAME
+ ": invalid channel selector (msg %08x)\n", msg);
+ }
+ ret = IRQ_HANDLED;
+ status = readl(mbox->status);
+ }
+ return ret;
+}
+
+static struct irqaction mbox_irqaction = {
+ .name = "ARM Mailbox IRQ",
+ .flags = IRQF_DISABLED | IRQF_IRQPOLL,
+ .handler = mbox_irq,
+};
+
+/* ----------------------------------------------------------------------
+ * Mailbox Methods
+ * -------------------------------------------------------------------- */
+
+static struct device *mbox_dev; /* we assume there's only one! */
+
+static int dev_mbox_write(struct device *dev, unsigned chan, uint32_t data28)
+{
+ int rc;
+
+ struct vc_mailbox *mailbox = dev_get_drvdata(dev);
+ device_lock(dev);
+ rc = mbox_write(mailbox, chan, data28);
+ device_unlock(dev);
+
+ return rc;
+}
+
+static int dev_mbox_read(struct device *dev, unsigned chan, uint32_t *data28)
+{
+ int rc;
+
+ struct vc_mailbox *mailbox = dev_get_drvdata(dev);
+ device_lock(dev);
+ rc = mbox_read(mailbox, chan, data28);
+ device_unlock(dev);
+
+ return rc;
+}
+
+extern int bcm_mailbox_write(unsigned chan, uint32_t data28)
+{
+ if (mbox_dev)
+ return dev_mbox_write(mbox_dev, chan, data28);
+ else
+ return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(bcm_mailbox_write);
+
+extern int bcm_mailbox_read(unsigned chan, uint32_t *data28)
+{
+ if (mbox_dev)
+ return dev_mbox_read(mbox_dev, chan, data28);
+ else
+ return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(bcm_mailbox_read);
+
+static void dev_mbox_register(const char *dev_name, struct device *dev)
+{
+ mbox_dev = dev;
+}
+
+static int mbox_copy_from_user(void *dst, const void *src, int size)
+{
+ if ( (uint32_t)src < TASK_SIZE)
+ {
+ return copy_from_user(dst, src, size);
+ }
+ else
+ {
+ memcpy( dst, src, size );
+ return 0;
+ }
+}
+
+static int mbox_copy_to_user(void *dst, const void *src, int size)
+{
+ if ( (uint32_t)dst < TASK_SIZE)
+ {
+ return copy_to_user(dst, src, size);
+ }
+ else
+ {
+ memcpy( dst, src, size );
+ return 0;
+ }
+}
+
+static DEFINE_MUTEX(mailbox_lock);
+extern int bcm_mailbox_property(void *data, int size)
+{
+ uint32_t success;
+ dma_addr_t mem_bus; /* the memory address accessed from videocore */
+ void *mem_kern; /* the memory address accessed from driver */
+ int s = 0;
+
+ mutex_lock(&mailbox_lock);
+ /* allocate some memory for the messages communicating with GPU */
+ mem_kern = dma_alloc_coherent(NULL, PAGE_ALIGN(size), &mem_bus, GFP_ATOMIC);
+ if (mem_kern) {
+ /* create the message */
+ mbox_copy_from_user(mem_kern, data, size);
+
+ /* send the message */
+ wmb();
+ s = bcm_mailbox_write(MBOX_CHAN_PROPERTY, (uint32_t)mem_bus);
+ if (s == 0) {
+ s = bcm_mailbox_read(MBOX_CHAN_PROPERTY, &success);
+ }
+ if (s == 0) {
+ /* copy the response */
+ rmb();
+ mbox_copy_to_user(data, mem_kern, size);
+ }
+ dma_free_coherent(NULL, PAGE_ALIGN(size), mem_kern, mem_bus);
+ } else {
+ s = -ENOMEM;
+ }
+ if (s != 0)
+ printk(KERN_ERR DRIVER_NAME ": %s failed (%d)\n", __func__, s);
+
+ mutex_unlock(&mailbox_lock);
+ return s;
+}
+EXPORT_SYMBOL_GPL(bcm_mailbox_property);
+
+/* ----------------------------------------------------------------------
+ * Platform Device for Mailbox
+ * -------------------------------------------------------------------- */
+
+/*
+ * Is the device open right now? Used to prevent
+ * concurent access into the same device
+ */
+static int Device_Open = 0;
+
+/*
+ * This is called whenever a process attempts to open the device file
+ */
+static int device_open(struct inode *inode, struct file *file)
+{
+ /*
+ * We don't want to talk to two processes at the same time
+ */
+ if (Device_Open)
+ return -EBUSY;
+
+ Device_Open++;
+ /*
+ * Initialize the message
+ */
+ try_module_get(THIS_MODULE);
+ return 0;
+}
+
+static int device_release(struct inode *inode, struct file *file)
+{
+ /*
+ * We're now ready for our next caller
+ */
+ Device_Open--;
+
+ module_put(THIS_MODULE);
+ return 0;
+}
+
+/*
+ * This function is called whenever a process tries to do an ioctl on our
+ * device file. We get two extra parameters (additional to the inode and file
+ * structures, which all device functions get): the number of the ioctl called
+ * and the parameter given to the ioctl function.
+ *
+ * If the ioctl is write or read/write (meaning output is returned to the
+ * calling process), the ioctl call returns the output of this function.
+ *
+ */
+static long device_ioctl(struct file *file, /* see include/linux/fs.h */
+ unsigned int ioctl_num, /* number and param for ioctl */
+ unsigned long ioctl_param)
+{
+ unsigned size;
+ /*
+ * Switch according to the ioctl called
+ */
+ switch (ioctl_num) {
+ case IOCTL_MBOX_PROPERTY:
+ /*
+ * Receive a pointer to a message (in user space) and set that
+ * to be the device's message. Get the parameter given to
+ * ioctl by the process.
+ */
+ mbox_copy_from_user(&size, (void *)ioctl_param, sizeof size);
+ return bcm_mailbox_property((void *)ioctl_param, size);
+ break;
+ default:
+ printk(KERN_ERR DRIVER_NAME "unknown ioctl: %d\n", ioctl_num);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/* Module Declarations */
+
+/*
+ * This structure will hold the functions to be called
+ * when a process does something to the device we
+ * created. Since a pointer to this structure is kept in
+ * the devices table, it can't be local to
+ * init_module. NULL is for unimplemented functios.
+ */
+struct file_operations fops = {
+ .unlocked_ioctl = device_ioctl,
+ .open = device_open,
+ .release = device_release, /* a.k.a. close */
+};
+
+static int bcm_vcio_probe(struct platform_device *pdev)
+{
+ int ret = 0;
+ struct vc_mailbox *mailbox;
+
+ mailbox = kzalloc(sizeof(*mailbox), GFP_KERNEL);
+ if (NULL == mailbox) {
+ printk(KERN_ERR DRIVER_NAME ": failed to allocate "
+ "mailbox memory\n");
+ ret = -ENOMEM;
+ } else {
+ struct resource *res;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL) {
+ printk(KERN_ERR DRIVER_NAME ": failed to obtain memory "
+ "resource\n");
+ ret = -ENODEV;
+ kfree(mailbox);
+ } else {
+ /* should be based on the registers from res really */
+ mbox_init(mailbox, &pdev->dev, ARM_0_MAIL0_RD);
+
+ platform_set_drvdata(pdev, mailbox);
+ dev_mbox_register(DRIVER_NAME, &pdev->dev);
+
+ mbox_irqaction.dev_id = mailbox;
+ setup_irq(IRQ_ARM_MAILBOX, &mbox_irqaction);
+ printk(KERN_INFO DRIVER_NAME ": mailbox at %p\n",
+ __io_address(ARM_0_MAIL0_RD));
+ }
+ }
+
+ if (ret == 0) {
+ /*
+ * Register the character device
+ */
+ ret = register_chrdev(MAJOR_NUM, DEVICE_FILE_NAME, &fops);
+
+ /*
+ * Negative values signify an error
+ */
+ if (ret < 0) {
+ printk(KERN_ERR DRIVER_NAME
+ "Failed registering the character device %d\n", ret);
+ return ret;
+ }
+ }
+ return ret;
+}
+
+static int bcm_vcio_remove(struct platform_device *pdev)
+{
+ struct vc_mailbox *mailbox = platform_get_drvdata(pdev);
+
+ platform_set_drvdata(pdev, NULL);
+ kfree(mailbox);
+
+ return 0;
+}
+
+static struct platform_driver bcm_mbox_driver = {
+ .probe = bcm_vcio_probe,
+ .remove = bcm_vcio_remove,
+
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init bcm_mbox_init(void)
+{
+ int ret;
+
+ printk(KERN_INFO "mailbox: Broadcom VideoCore Mailbox driver\n");
+
+ ret = platform_driver_register(&bcm_mbox_driver);
+ if (ret != 0) {
+ printk(KERN_ERR DRIVER_NAME ": failed to register "
+ "on platform\n");
+ }
+
+ return ret;
+}
+
+static void __exit bcm_mbox_exit(void)
+{
+ platform_driver_unregister(&bcm_mbox_driver);
+}
+
+arch_initcall(bcm_mbox_init); /* Initialize early */
+module_exit(bcm_mbox_exit);
+
+MODULE_AUTHOR("Gray Girling");
+MODULE_DESCRIPTION("ARM I/O to VideoCore processor");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bcm-mbox");
--- /dev/null
+++ b/arch/arm/mach-bcm2708/vc_mem.c
@@ -0,0 +1,462 @@
+/*****************************************************************************
+* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/fs.h>
+#include <linux/device.h>
+#include <linux/cdev.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/proc_fs.h>
+#include <asm/uaccess.h>
+#include <linux/dma-mapping.h>
+
+#ifdef CONFIG_ARCH_KONA
+#include <chal/chal_ipc.h>
+#elif CONFIG_ARCH_BCM2708
+#else
+#include <csp/chal_ipc.h>
+#endif
+
+#include "mach/vc_mem.h"
+#include <mach/vcio.h>
+
+#define DRIVER_NAME "vc-mem"
+
+// Uncomment to enable debug logging
+// #define ENABLE_DBG
+
+#if defined(ENABLE_DBG)
+#define LOG_DBG( fmt, ... ) printk( KERN_INFO fmt "\n", ##__VA_ARGS__ )
+#else
+#define LOG_DBG( fmt, ... )
+#endif
+#define LOG_ERR( fmt, ... ) printk( KERN_ERR fmt "\n", ##__VA_ARGS__ )
+
+// Device (/dev) related variables
+static dev_t vc_mem_devnum = 0;
+static struct class *vc_mem_class = NULL;
+static struct cdev vc_mem_cdev;
+static int vc_mem_inited = 0;
+
+// Proc entry
+static struct proc_dir_entry *vc_mem_proc_entry;
+
+/*
+ * Videocore memory addresses and size
+ *
+ * Drivers that wish to know the videocore memory addresses and sizes should
+ * use these variables instead of the MM_IO_BASE and MM_ADDR_IO defines in
+ * headers. This allows the other drivers to not be tied down to a a certain
+ * address/size at compile time.
+ *
+ * In the future, the goal is to have the videocore memory virtual address and
+ * size be calculated at boot time rather than at compile time. The decision of
+ * where the videocore memory resides and its size would be in the hands of the
+ * bootloader (and/or kernel). When that happens, the values of these variables
+ * would be calculated and assigned in the init function.
+ */
+// in the 2835 VC in mapped above ARM, but ARM has full access to VC space
+unsigned long mm_vc_mem_phys_addr = 0x00000000;
+unsigned int mm_vc_mem_size = 0;
+unsigned int mm_vc_mem_base = 0;
+
+EXPORT_SYMBOL(mm_vc_mem_phys_addr);
+EXPORT_SYMBOL(mm_vc_mem_size);
+EXPORT_SYMBOL(mm_vc_mem_base);
+
+static uint phys_addr = 0;
+static uint mem_size = 0;
+static uint mem_base = 0;
+
+
+/****************************************************************************
+*
+* vc_mem_open
+*
+***************************************************************************/
+
+static int
+vc_mem_open(struct inode *inode, struct file *file)
+{
+ (void) inode;
+ (void) file;
+
+ LOG_DBG("%s: called file = 0x%p", __func__, file);
+
+ return 0;
+}
+
+/****************************************************************************
+*
+* vc_mem_release
+*
+***************************************************************************/
+
+static int
+vc_mem_release(struct inode *inode, struct file *file)
+{
+ (void) inode;
+ (void) file;
+
+ LOG_DBG("%s: called file = 0x%p", __func__, file);
+
+ return 0;
+}
+
+/****************************************************************************
+*
+* vc_mem_get_size
+*
+***************************************************************************/
+
+static void
+vc_mem_get_size(void)
+{
+}
+
+/****************************************************************************
+*
+* vc_mem_get_base
+*
+***************************************************************************/
+
+static void
+vc_mem_get_base(void)
+{
+}
+
+/****************************************************************************
+*
+* vc_mem_get_current_size
+*
+***************************************************************************/
+
+int
+vc_mem_get_current_size(void)
+{
+ return mm_vc_mem_size;
+}
+
+EXPORT_SYMBOL_GPL(vc_mem_get_current_size);
+
+/****************************************************************************
+*
+* vc_mem_ioctl
+*
+***************************************************************************/
+
+static long
+vc_mem_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+ int rc = 0;
+
+ (void) cmd;
+ (void) arg;
+
+ LOG_DBG("%s: called file = 0x%p", __func__, file);
+
+ switch (cmd) {
+ case VC_MEM_IOC_MEM_PHYS_ADDR:
+ {
+ LOG_DBG("%s: VC_MEM_IOC_MEM_PHYS_ADDR=0x%p",
+ __func__, (void *) mm_vc_mem_phys_addr);
+
+ if (copy_to_user((void *) arg, &mm_vc_mem_phys_addr,
+ sizeof (mm_vc_mem_phys_addr)) != 0) {
+ rc = -EFAULT;
+ }
+ break;
+ }
+ case VC_MEM_IOC_MEM_SIZE:
+ {
+ // Get the videocore memory size first
+ vc_mem_get_size();
+
+ LOG_DBG("%s: VC_MEM_IOC_MEM_SIZE=%u", __func__,
+ mm_vc_mem_size);
+
+ if (copy_to_user((void *) arg, &mm_vc_mem_size,
+ sizeof (mm_vc_mem_size)) != 0) {
+ rc = -EFAULT;
+ }
+ break;
+ }
+ case VC_MEM_IOC_MEM_BASE:
+ {
+ // Get the videocore memory base
+ vc_mem_get_base();
+
+ LOG_DBG("%s: VC_MEM_IOC_MEM_BASE=%u", __func__,
+ mm_vc_mem_base);
+
+ if (copy_to_user((void *) arg, &mm_vc_mem_base,
+ sizeof (mm_vc_mem_base)) != 0) {
+ rc = -EFAULT;
+ }
+ break;
+ }
+ case VC_MEM_IOC_MEM_LOAD:
+ {
+ // Get the videocore memory base
+ vc_mem_get_base();
+
+ LOG_DBG("%s: VC_MEM_IOC_MEM_LOAD=%u", __func__,
+ mm_vc_mem_base);
+
+ if (copy_to_user((void *) arg, &mm_vc_mem_base,
+ sizeof (mm_vc_mem_base)) != 0) {
+ rc = -EFAULT;
+ }
+ break;
+ }
+ default:
+ {
+ return -ENOTTY;
+ }
+ }
+ LOG_DBG("%s: file = 0x%p returning %d", __func__, file, rc);
+
+ return rc;
+}
+
+/****************************************************************************
+*
+* vc_mem_mmap
+*
+***************************************************************************/
+
+static int
+vc_mem_mmap(struct file *filp, struct vm_area_struct *vma)
+{
+ int rc = 0;
+ unsigned long length = vma->vm_end - vma->vm_start;
+ unsigned long offset = vma->vm_pgoff << PAGE_SHIFT;
+
+ LOG_DBG("%s: vm_start = 0x%08lx vm_end = 0x%08lx vm_pgoff = 0x%08lx",
+ __func__, (long) vma->vm_start, (long) vma->vm_end,
+ (long) vma->vm_pgoff);
+
+ if (offset + length > mm_vc_mem_size) {
+ LOG_ERR("%s: length %ld is too big", __func__, length);
+ return -EINVAL;
+ }
+ // Do not cache the memory map
+ vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+
+ rc = remap_pfn_range(vma, vma->vm_start,
+ (mm_vc_mem_phys_addr >> PAGE_SHIFT) +
+ vma->vm_pgoff, length, vma->vm_page_prot);
+ if (rc != 0) {
+ LOG_ERR("%s: remap_pfn_range failed (rc=%d)", __func__, rc);
+ }
+
+ return rc;
+}
+
+/****************************************************************************
+*
+* File Operations for the driver.
+*
+***************************************************************************/
+
+static const struct file_operations vc_mem_fops = {
+ .owner = THIS_MODULE,
+ .open = vc_mem_open,
+ .release = vc_mem_release,
+ .unlocked_ioctl = vc_mem_ioctl,
+ .mmap = vc_mem_mmap,
+};
+
+/****************************************************************************
+*
+* vc_mem_proc_read
+*
+***************************************************************************/
+
+static int
+vc_mem_proc_read(char *buf, char **start, off_t offset, int count, int *eof,
+ void *data)
+{
+ char *p = buf;
+
+ (void) start;
+ (void) count;
+ (void) data;
+
+ if (offset > 0) {
+ *eof = 1;
+ return 0;
+ }
+ // Get the videocore memory size first
+ vc_mem_get_size();
+
+ p += sprintf(p, "Videocore memory:\n");
+ if (mm_vc_mem_phys_addr != 0)
+ p += sprintf(p, " Physical address: 0x%p\n",
+ (void *) mm_vc_mem_phys_addr);
+ else
+ p += sprintf(p, " Physical address: 0x00000000\n");
+ p += sprintf(p, " Length (bytes): %u\n", mm_vc_mem_size);
+
+ *eof = 1;
+ return p - buf;
+}
+
+/****************************************************************************
+*
+* vc_mem_proc_write
+*
+***************************************************************************/
+
+static int
+vc_mem_proc_write(struct file *file, const char __user * buffer,
+ unsigned long count, void *data)
+{
+ int rc = -EFAULT;
+ char input_str[10];
+
+ memset(input_str, 0, sizeof (input_str));
+
+ if (count > sizeof (input_str)) {
+ LOG_ERR("%s: input string length too long", __func__);
+ goto out;
+ }
+
+ if (copy_from_user(input_str, buffer, count - 1)) {
+ LOG_ERR("%s: failed to get input string", __func__);
+ goto out;
+ }
+
+ if (strncmp(input_str, "connect", strlen("connect")) == 0) {
+ // Get the videocore memory size from the videocore
+ vc_mem_get_size();
+ }
+
+ out:
+ return rc;
+}
+
+/****************************************************************************
+*
+* vc_mem_init
+*
+***************************************************************************/
+
+static int __init
+vc_mem_init(void)
+{
+ int rc = -EFAULT;
+ struct device *dev;
+
+ LOG_DBG("%s: called", __func__);
+
+ mm_vc_mem_phys_addr = phys_addr;
+ mm_vc_mem_size = mem_size;
+ mm_vc_mem_base = mem_base;
+
+ vc_mem_get_size();
+
+ printk("vc-mem: phys_addr:0x%08lx mem_base=0x%08x mem_size:0x%08x(%u MiB)\n",
+ mm_vc_mem_phys_addr, mm_vc_mem_base, mm_vc_mem_size, mm_vc_mem_size / (1024 * 1024));
+
+ if ((rc = alloc_chrdev_region(&vc_mem_devnum, 0, 1, DRIVER_NAME)) < 0) {
+ LOG_ERR("%s: alloc_chrdev_region failed (rc=%d)", __func__, rc);
+ goto out_err;
+ }
+
+ cdev_init(&vc_mem_cdev, &vc_mem_fops);
+ if ((rc = cdev_add(&vc_mem_cdev, vc_mem_devnum, 1)) != 0) {
+ LOG_ERR("%s: cdev_add failed (rc=%d)", __func__, rc);
+ goto out_unregister;
+ }
+
+ vc_mem_class = class_create(THIS_MODULE, DRIVER_NAME);
+ if (IS_ERR(vc_mem_class)) {
+ rc = PTR_ERR(vc_mem_class);
+ LOG_ERR("%s: class_create failed (rc=%d)", __func__, rc);
+ goto out_cdev_del;
+ }
+
+ dev = device_create(vc_mem_class, NULL, vc_mem_devnum, NULL,
+ DRIVER_NAME);
+ if (IS_ERR(dev)) {
+ rc = PTR_ERR(dev);
+ LOG_ERR("%s: device_create failed (rc=%d)", __func__, rc);
+ goto out_class_destroy;
+ }
+
+#if 0
+ vc_mem_proc_entry = create_proc_entry(DRIVER_NAME, 0444, NULL);
+ if (vc_mem_proc_entry == NULL) {
+ rc = -EFAULT;
+ LOG_ERR("%s: create_proc_entry failed", __func__);
+ goto out_device_destroy;
+ }
+ vc_mem_proc_entry->read_proc = vc_mem_proc_read;
+ vc_mem_proc_entry->write_proc = vc_mem_proc_write;
+#endif
+
+ vc_mem_inited = 1;
+ return 0;
+
+ out_device_destroy:
+ device_destroy(vc_mem_class, vc_mem_devnum);
+
+ out_class_destroy:
+ class_destroy(vc_mem_class);
+ vc_mem_class = NULL;
+
+ out_cdev_del:
+ cdev_del(&vc_mem_cdev);
+
+ out_unregister:
+ unregister_chrdev_region(vc_mem_devnum, 1);
+
+ out_err:
+ return -1;
+}
+
+/****************************************************************************
+*
+* vc_mem_exit
+*
+***************************************************************************/
+
+static void __exit
+vc_mem_exit(void)
+{
+ LOG_DBG("%s: called", __func__);
+
+ if (vc_mem_inited) {
+#if 0
+ remove_proc_entry(vc_mem_proc_entry->name, NULL);
+#endif
+ device_destroy(vc_mem_class, vc_mem_devnum);
+ class_destroy(vc_mem_class);
+ cdev_del(&vc_mem_cdev);
+ unregister_chrdev_region(vc_mem_devnum, 1);
+ }
+}
+
+module_init(vc_mem_init);
+module_exit(vc_mem_exit);
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Broadcom Corporation");
+
+module_param(phys_addr, uint, 0644);
+module_param(mem_size, uint, 0644);
+module_param(mem_base, uint, 0644);
+
--- /dev/null
+++ b/arch/arm/mach-bcm2708/vc_support.c
@@ -0,0 +1,319 @@
+/*
+ * vc_support.c
+ *
+ * Created on: 25 Nov 2012
+ * Author: Simon
+ */
+
+#include <linux/module.h>
+#include <mach/vcio.h>
+
+#ifdef ECLIPSE_IGNORE
+
+#define __user
+#define __init
+#define __exit
+#define __iomem
+#define KERN_DEBUG
+#define KERN_ERR
+#define KERN_WARNING
+#define KERN_INFO
+#define _IOWR(a, b, c) b
+#define _IOW(a, b, c) b
+#define _IO(a, b) b
+
+#endif
+
+/****** VC MAILBOX FUNCTIONALITY ******/
+unsigned int AllocateVcMemory(unsigned int *pHandle, unsigned int size, unsigned int alignment, unsigned int flags)
+{
+ struct vc_msg
+ {
+ unsigned int m_msgSize;
+ unsigned int m_response;
+
+ struct vc_tag
+ {
+ unsigned int m_tagId;
+ unsigned int m_sendBufferSize;
+ union {
+ unsigned int m_sendDataSize;
+ unsigned int m_recvDataSize;
+ };
+
+ struct args
+ {
+ union {
+ unsigned int m_size;
+ unsigned int m_handle;
+ };
+ unsigned int m_alignment;
+ unsigned int m_flags;
+ } m_args;
+ } m_tag;
+
+ unsigned int m_endTag;
+ } msg;
+ int s;
+
+ msg.m_msgSize = sizeof(msg);
+ msg.m_response = 0;
+ msg.m_endTag = 0;
+
+ //fill in the tag for the allocation command
+ msg.m_tag.m_tagId = 0x3000c;
+ msg.m_tag.m_sendBufferSize = 12;
+ msg.m_tag.m_sendDataSize = 12;
+
+ //fill in our args
+ msg.m_tag.m_args.m_size = size;
+ msg.m_tag.m_args.m_alignment = alignment;
+ msg.m_tag.m_args.m_flags = flags;
+
+ //run the command
+ s = bcm_mailbox_property(&msg, sizeof(msg));
+
+ if (s == 0 && msg.m_response == 0x80000000 && msg.m_tag.m_recvDataSize == 0x80000004)
+ {
+ *pHandle = msg.m_tag.m_args.m_handle;
+ return 0;
+ }
+ else
+ {
+ printk(KERN_ERR "failed to allocate vc memory: s=%d response=%08x recv data size=%08x\n",
+ s, msg.m_response, msg.m_tag.m_recvDataSize);
+ return 1;
+ }
+}
+
+unsigned int ReleaseVcMemory(unsigned int handle)
+{
+ struct vc_msg
+ {
+ unsigned int m_msgSize;
+ unsigned int m_response;
+
+ struct vc_tag
+ {
+ unsigned int m_tagId;
+ unsigned int m_sendBufferSize;
+ union {
+ unsigned int m_sendDataSize;
+ unsigned int m_recvDataSize;
+ };
+
+ struct args
+ {
+ union {
+ unsigned int m_handle;
+ unsigned int m_error;
+ };
+ } m_args;
+ } m_tag;
+
+ unsigned int m_endTag;
+ } msg;
+ int s;
+
+ msg.m_msgSize = sizeof(msg);
+ msg.m_response = 0;
+ msg.m_endTag = 0;
+
+ //fill in the tag for the release command
+ msg.m_tag.m_tagId = 0x3000f;
+ msg.m_tag.m_sendBufferSize = 4;
+ msg.m_tag.m_sendDataSize = 4;
+
+ //pass across the handle
+ msg.m_tag.m_args.m_handle = handle;
+
+ s = bcm_mailbox_property(&msg, sizeof(msg));
+
+ if (s == 0 && msg.m_response == 0x80000000 && msg.m_tag.m_recvDataSize == 0x80000004 && msg.m_tag.m_args.m_error == 0)
+ return 0;
+ else
+ {
+ printk(KERN_ERR "failed to release vc memory: s=%d response=%08x recv data size=%08x error=%08x\n",
+ s, msg.m_response, msg.m_tag.m_recvDataSize, msg.m_tag.m_args.m_error);
+ return 1;
+ }
+}
+
+unsigned int LockVcMemory(unsigned int *pBusAddress, unsigned int handle)
+{
+ struct vc_msg
+ {
+ unsigned int m_msgSize;
+ unsigned int m_response;
+
+ struct vc_tag
+ {
+ unsigned int m_tagId;
+ unsigned int m_sendBufferSize;
+ union {
+ unsigned int m_sendDataSize;
+ unsigned int m_recvDataSize;
+ };
+
+ struct args
+ {
+ union {
+ unsigned int m_handle;
+ unsigned int m_busAddress;
+ };
+ } m_args;
+ } m_tag;
+
+ unsigned int m_endTag;
+ } msg;
+ int s;
+
+ msg.m_msgSize = sizeof(msg);
+ msg.m_response = 0;
+ msg.m_endTag = 0;
+
+ //fill in the tag for the lock command
+ msg.m_tag.m_tagId = 0x3000d;
+ msg.m_tag.m_sendBufferSize = 4;
+ msg.m_tag.m_sendDataSize = 4;
+
+ //pass across the handle
+ msg.m_tag.m_args.m_handle = handle;
+
+ s = bcm_mailbox_property(&msg, sizeof(msg));
+
+ if (s == 0 && msg.m_response == 0x80000000 && msg.m_tag.m_recvDataSize == 0x80000004)
+ {
+ //pick out the bus address
+ *pBusAddress = msg.m_tag.m_args.m_busAddress;
+ return 0;
+ }
+ else
+ {
+ printk(KERN_ERR "failed to lock vc memory: s=%d response=%08x recv data size=%08x\n",
+ s, msg.m_response, msg.m_tag.m_recvDataSize);
+ return 1;
+ }
+}
+
+unsigned int UnlockVcMemory(unsigned int handle)
+{
+ struct vc_msg
+ {
+ unsigned int m_msgSize;
+ unsigned int m_response;
+
+ struct vc_tag
+ {
+ unsigned int m_tagId;
+ unsigned int m_sendBufferSize;
+ union {
+ unsigned int m_sendDataSize;
+ unsigned int m_recvDataSize;
+ };
+
+ struct args
+ {
+ union {
+ unsigned int m_handle;
+ unsigned int m_error;
+ };
+ } m_args;
+ } m_tag;
+
+ unsigned int m_endTag;
+ } msg;
+ int s;
+
+ msg.m_msgSize = sizeof(msg);
+ msg.m_response = 0;
+ msg.m_endTag = 0;
+
+ //fill in the tag for the unlock command
+ msg.m_tag.m_tagId = 0x3000e;
+ msg.m_tag.m_sendBufferSize = 4;
+ msg.m_tag.m_sendDataSize = 4;
+
+ //pass across the handle
+ msg.m_tag.m_args.m_handle = handle;
+
+ s = bcm_mailbox_property(&msg, sizeof(msg));
+
+ //check the error code too
+ if (s == 0 && msg.m_response == 0x80000000 && msg.m_tag.m_recvDataSize == 0x80000004 && msg.m_tag.m_args.m_error == 0)
+ return 0;
+ else
+ {
+ printk(KERN_ERR "failed to unlock vc memory: s=%d response=%08x recv data size=%08x error%08x\n",
+ s, msg.m_response, msg.m_tag.m_recvDataSize, msg.m_tag.m_args.m_error);
+ return 1;
+ }
+}
+
+unsigned int ExecuteVcCode(unsigned int code,
+ unsigned int r0, unsigned int r1, unsigned int r2, unsigned int r3, unsigned int r4, unsigned int r5)
+{
+ struct vc_msg
+ {
+ unsigned int m_msgSize;
+ unsigned int m_response;
+
+ struct vc_tag
+ {
+ unsigned int m_tagId;
+ unsigned int m_sendBufferSize;
+ union {
+ unsigned int m_sendDataSize;
+ unsigned int m_recvDataSize;
+ };
+
+ struct args
+ {
+ union {
+ unsigned int m_pCode;
+ unsigned int m_return;
+ };
+ unsigned int m_r0;
+ unsigned int m_r1;
+ unsigned int m_r2;
+ unsigned int m_r3;
+ unsigned int m_r4;
+ unsigned int m_r5;
+ } m_args;
+ } m_tag;
+
+ unsigned int m_endTag;
+ } msg;
+ int s;
+
+ msg.m_msgSize = sizeof(msg);
+ msg.m_response = 0;
+ msg.m_endTag = 0;
+
+ //fill in the tag for the unlock command
+ msg.m_tag.m_tagId = 0x30010;
+ msg.m_tag.m_sendBufferSize = 28;
+ msg.m_tag.m_sendDataSize = 28;
+
+ //pass across the handle
+ msg.m_tag.m_args.m_pCode = code;
+ msg.m_tag.m_args.m_r0 = r0;
+ msg.m_tag.m_args.m_r1 = r1;
+ msg.m_tag.m_args.m_r2 = r2;
+ msg.m_tag.m_args.m_r3 = r3;
+ msg.m_tag.m_args.m_r4 = r4;
+ msg.m_tag.m_args.m_r5 = r5;
+
+ s = bcm_mailbox_property(&msg, sizeof(msg));
+
+ //check the error code too
+ if (s == 0 && msg.m_response == 0x80000000 && msg.m_tag.m_recvDataSize == 0x80000004)
+ return msg.m_tag.m_args.m_return;
+ else
+ {
+ printk(KERN_ERR "failed to execute: s=%d response=%08x recv data size=%08x\n",
+ s, msg.m_response, msg.m_tag.m_recvDataSize);
+ return 1;
+ }
+}
+
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -144,6 +144,7 @@ textofs-$(CONFIG_ARCH_MSM8960) := 0x0020
# by CONFIG_* macro name.
machine-$(CONFIG_ARCH_AT91) += at91
machine-$(CONFIG_ARCH_BCM) += bcm
+machine-$(CONFIG_ARCH_BCM2708) += bcm2708
machine-$(CONFIG_ARCH_BCM2835) += bcm2835
machine-$(CONFIG_ARCH_CLPS711X) += clps711x
machine-$(CONFIG_ARCH_CNS3XXX) += cns3xxx
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -358,7 +358,7 @@ config CPU_PJ4B
# ARMv6
config CPU_V6
- bool "Support ARM V6 processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX
+ bool "Support ARM V6 processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX || MACH_BCM2708
select CPU_32v6
select CPU_ABRT_EV6
select CPU_CACHE_V6
--- a/arch/arm/mm/proc-v6.S
+++ b/arch/arm/mm/proc-v6.S
@@ -73,10 +73,19 @@ ENDPROC(cpu_v6_reset)
*
* IRQs are already disabled.
*/
+
+/* See jira SW-5991 for details of this workaround */
ENTRY(cpu_v6_do_idle)
- mov r1, #0
- mcr p15, 0, r1, c7, c10, 4 @ DWB - WFI may enter a low-power mode
- mcr p15, 0, r1, c7, c0, 4 @ wait for interrupt
+ .align 5
+ mov r1, #2
+1: subs r1, #1
+ nop
+ mcreq p15, 0, r1, c7, c10, 4 @ DWB - WFI may enter a low-power mode
+ mcreq p15, 0, r1, c7, c0, 4 @ wait for interrupt
+ nop
+ nop
+ nop
+ bne 1b
mov pc, lr
ENTRY(cpu_v6_dcache_clean_area)
--- a/arch/arm/tools/mach-types
+++ b/arch/arm/tools/mach-types
@@ -522,6 +522,7 @@ torbreck MACH_TORBRECK TORBRECK 3090
prima2_evb MACH_PRIMA2_EVB PRIMA2_EVB 3103
paz00 MACH_PAZ00 PAZ00 3128
acmenetusfoxg20 MACH_ACMENETUSFOXG20 ACMENETUSFOXG20 3129
+bcm2708 MACH_BCM2708 BCM2708 3138
ag5evm MACH_AG5EVM AG5EVM 3189
ics_if_voip MACH_ICS_IF_VOIP ICS_IF_VOIP 3206
wlf_cragg_6410 MACH_WLF_CRAGG_6410 WLF_CRAGG_6410 3207