From fff71f293b81ea6aa254397236484437b491ed9c Mon Sep 17 00:00:00 2001 From: Phil Elwell Date: Mon, 8 Feb 2016 09:46:33 +0000 Subject: [PATCH] BCM270X_DT: Adjust overlay README formatting --- arch/arm/boot/dts/overlays/README | 414 +++++++++++++++++++------------------- 1 file changed, 207 insertions(+), 207 deletions(-) --- a/arch/arm/boot/dts/overlays/README +++ b/arch/arm/boot/dts/overlays/README @@ -83,58 +83,58 @@ Name: Info: Configures the base Raspberry Pi hardware Load: Params: - audio Set to "on" to enable the onboard ALSA audio - interface (default "off") + audio Set to "on" to enable the onboard ALSA audio + interface (default "off") - i2c_arm Set to "on" to enable the ARM's i2c interface - (default "off") + i2c_arm Set to "on" to enable the ARM's i2c interface + (default "off") - i2c_vc Set to "on" to enable the i2c interface - usually reserved for the VideoCore processor - (default "off") + i2c_vc Set to "on" to enable the i2c interface + usually reserved for the VideoCore processor + (default "off") - i2c An alias for i2c_arm + i2c An alias for i2c_arm - i2c_arm_baudrate Set the baudrate of the ARM's i2c interface - (default "100000") + i2c_arm_baudrate Set the baudrate of the ARM's i2c interface + (default "100000") - i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface - (default "100000") + i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface + (default "100000") - i2c_baudrate An alias for i2c_arm_baudrate + i2c_baudrate An alias for i2c_arm_baudrate - i2s Set to "on" to enable the i2s interface - (default "off") + i2s Set to "on" to enable the i2s interface + (default "off") - spi Set to "on" to enable the spi interfaces - (default "off") + spi Set to "on" to enable the spi interfaces + (default "off") - random Set to "on" to enable the hardware random - number generator (default "on") + random Set to "on" to enable the hardware random + number generator (default "on") - uart0 Set to "off" to disable uart0 (default "on") + uart0 Set to "off" to disable uart0 (default "on") - watchdog Set to "on" to enable the hardware watchdog - (default "off") + watchdog Set to "on" to enable the hardware watchdog + (default "off") - act_led_trigger Choose which activity the LED tracks. - Use "heartbeat" for a nice load indicator. - (default "mmc") + act_led_trigger Choose which activity the LED tracks. + Use "heartbeat" for a nice load indicator. + (default "mmc") - act_led_activelow Set to "on" to invert the sense of the LED - (default "off") + act_led_activelow Set to "on" to invert the sense of the LED + (default "off") - act_led_gpio Set which GPIO to use for the activity LED - (in case you want to connect it to an external - device) - (default "16" on a non-Plus board, "47" on a - Plus or Pi 2) + act_led_gpio Set which GPIO to use for the activity LED + (in case you want to connect it to an external + device) + (default "16" on a non-Plus board, "47" on a + Plus or Pi 2) pwr_led_trigger pwr_led_activelow pwr_led_gpio - As for act_led_*, but using the PWR LED. - Not available on Model A/B boards. + As for act_led_*, but using the PWR LED. + Not available on Model A/B boards. N.B. It is recommended to only enable those interfaces that are needed. Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc @@ -149,19 +149,19 @@ Params: Name: ads7846 Info: ADS7846 Touch controller Load: dtoverlay=ads7846,= -Params: cs SPI bus Chip Select (default 1) - speed SPI bus speed (default 2MHz, max 3.25MHz) - penirq GPIO used for PENIRQ. REQUIRED - penirq_pull Set GPIO pull (default 0=none, 2=pullup) - swapxy Swap x and y axis - xmin Minimum value on the X axis (default 0) - ymin Minimum value on the Y axis (default 0) - xmax Maximum value on the X axis (default 4095) - ymax Maximum value on the Y axis (default 4095) - pmin Minimum reported pressure value (default 0) - pmax Maximum reported pressure value (default 65535) - xohms Touchpanel sensitivity (X-plate resistance) - (default 400) +Params: cs SPI bus Chip Select (default 1) + speed SPI bus speed (default 2MHz, max 3.25MHz) + penirq GPIO used for PENIRQ. REQUIRED + penirq_pull Set GPIO pull (default 0=none, 2=pullup) + swapxy Swap x and y axis + xmin Minimum value on the X axis (default 0) + ymin Minimum value on the Y axis (default 0) + xmax Maximum value on the X axis (default 4095) + ymax Maximum value on the Y axis (default 4095) + pmin Minimum reported pressure value (default 0) + pmax Maximum reported pressure value (default 65535) + xohms Touchpanel sensitivity (X-plate resistance) + (default 400) penirq is required and usually xohms (60-100) has to be set as well. Apart from that, pmax (255) and swapxy are also common. @@ -175,12 +175,12 @@ Name: at86rf233 Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver, connected to spi0.0 Load: dtoverlay=at86rf233,= -Params: interrupt GPIO used for INT (default 23) - reset GPIO used for Reset (default 24) - sleep GPIO used for Sleep (default 25) - speed SPI bus speed in Hz (default 6000000) - trim Fine tuning of the internal capacitance - arrays (0=+0pF, 15=+4.5pF, default 15) +Params: interrupt GPIO used for INT (default 23) + reset GPIO used for Reset (default 24) + sleep GPIO used for Sleep (default 25) + speed SPI bus speed in Hz (default 6000000) + trim Fine tuning of the internal capacitance + arrays (0=+0pF, 15=+4.5pF, default 15) Name: bmp085_i2c-sensor @@ -194,8 +194,8 @@ Name: dht11 Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors Also sometimes found with the part number(s) AM230x. Load: dtoverlay=dht11,= -Params: gpiopin GPIO connected to the sensor's DATA output. - (default 4) +Params: gpiopin GPIO connected to the sensor's DATA output. + (default 4) Name: dwc-otg @@ -208,15 +208,15 @@ Params: Name: dwc2 Info: Selects the dwc2 USB controller driver Load: dtoverlay=dwc2,= -Params: dr_mode Dual role mode: "host", "peripheral" or "otg" +Params: dr_mode Dual role mode: "host", "peripheral" or "otg" - g-rx-fifo-size Size of rx fifo size in gadget mode + g-rx-fifo-size Size of rx fifo size in gadget mode - g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget - mode + g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget + mode - g-tx-fifo-size Size of periodic tx fifo per endpoint - (except ep0) in gadget mode + g-tx-fifo-size Size of periodic tx fifo per endpoint + (except ep0) in gadget mode [ The ds1307-rtc overlay has been deleted. See i2c-rtc. ] @@ -225,9 +225,9 @@ Params: dr_mode Dual ro Name: enc28j60 Info: Overlay for the Microchip ENC28J60 Ethernet Controller (SPI) Load: dtoverlay=enc28j60,= -Params: int_pin GPIO used for INT (default 25) +Params: int_pin GPIO used for INT (default 25) - speed SPI bus speed (default 12000000) + speed SPI bus speed (default 12000000) Name: gpio-ir @@ -237,26 +237,26 @@ Info: Use GPIO pin as rc-core style in not required! The key mapping and other decoding parameters can be configured by "ir-keytable" tool. Load: dtoverlay=gpio-ir,= -Params: gpio_pin Input pin number. Default is 18. +Params: gpio_pin Input pin number. Default is 18. - gpio_pull Desired pull-up/down state (off, down, up) - Default is "down". + gpio_pull Desired pull-up/down state (off, down, up) + Default is "down". - rc-map-name Default rc keymap (can also be changed by - ir-keytable), defaults to "rc-rc6-mce" + rc-map-name Default rc keymap (can also be changed by + ir-keytable), defaults to "rc-rc6-mce" Name: gpio-poweroff Info: Drives a GPIO high or low on reboot Load: dtoverlay=gpio-poweroff,= -Params: gpiopin GPIO for signalling (default 26) +Params: gpiopin GPIO for signalling (default 26) - active_low Set if the power control device requires a - high->low transition to trigger a power-down. - Note that this will require the support of a - custom dt-blob.bin to prevent a power-down - during the boot process, and that a reboot - will also cause the pin to go low. + active_low Set if the power control device requires a + high->low transition to trigger a power-down. + Note that this will require the support of a + custom dt-blob.bin to prevent a power-down + during the boot process, and that a reboot + will also cause the pin to go low. Name: hifiberry-amp @@ -300,65 +300,65 @@ Name: hy28a Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics Default values match Texy's display shield Load: dtoverlay=hy28a,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} - xohms Touchpanel sensitivity (X-plate resistance) + xohms Touchpanel sensitivity (X-plate resistance) - resetgpio GPIO used to reset controller + resetgpio GPIO used to reset controller - ledgpio GPIO used to control backlight + ledgpio GPIO used to control backlight Name: hy28b Info: HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics Default values match Texy's display shield Load: dtoverlay=hy28b,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} - xohms Touchpanel sensitivity (X-plate resistance) + xohms Touchpanel sensitivity (X-plate resistance) - resetgpio GPIO used to reset controller + resetgpio GPIO used to reset controller - ledgpio GPIO used to control backlight + ledgpio GPIO used to control backlight Name: i2c-gpio Info: Adds support for software i2c controller on gpio pins Load: dtoverlay=i2c-gpio,= -Params: i2c_gpio_sda GPIO used for I2C data (default "23") +Params: i2c_gpio_sda GPIO used for I2C data (default "23") - i2c_gpio_scl GPIO used for I2C clock (default "24") + i2c_gpio_scl GPIO used for I2C clock (default "24") - i2c_gpio_delay_us Clock delay in microseconds - (default "2" = ~100kHz) + i2c_gpio_delay_us Clock delay in microseconds + (default "2" = ~100kHz) Name: i2c-rtc Info: Adds support for a number of I2C Real Time Clock devices Load: dtoverlay=i2c-rtc,= -Params: ds1307 Select the DS1307 device +Params: ds1307 Select the DS1307 device - ds3231 Select the DS3231 device + ds3231 Select the DS3231 device - mcp7941x Select the MCP7941x device + mcp7941x Select the MCP7941x device - pcf2127 Select the PCF2127 device + pcf2127 Select the PCF2127 device - pcf8523 Select the PCF8523 device + pcf8523 Select the PCF8523 device - pcf8563 Select the PCF8563 device + pcf8563 Select the PCF8563 device Name: i2s-mmap @@ -396,70 +396,70 @@ Name: lirc-rpi Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi) Consult the module documentation for more details. Load: dtoverlay=lirc-rpi,= -Params: gpio_out_pin GPIO for output (default "17") +Params: gpio_out_pin GPIO for output (default "17") - gpio_in_pin GPIO for input (default "18") + gpio_in_pin GPIO for input (default "18") - gpio_in_pull Pull up/down/off on the input pin - (default "down") + gpio_in_pull Pull up/down/off on the input pin + (default "down") - sense Override the IR receive auto-detection logic: - "0" = force active-high - "1" = force active-low - "-1" = use auto-detection - (default "-1") + sense Override the IR receive auto-detection logic: + "0" = force active-high + "1" = force active-low + "-1" = use auto-detection + (default "-1") - softcarrier Turn the software carrier "on" or "off" - (default "on") + softcarrier Turn the software carrier "on" or "off" + (default "on") - invert "on" = invert the output pin (default "off") + invert "on" = invert the output pin (default "off") - debug "on" = enable additional debug messages - (default "off") + debug "on" = enable additional debug messages + (default "off") Name: mcp2515-can0 Info: Configures the MCP2515 CAN controller on spi0.0 Load: dtoverlay=mcp2515-can0,= -Params: oscillator Clock frequency for the CAN controller (Hz) +Params: oscillator Clock frequency for the CAN controller (Hz) - spimaxfrequency Maximum SPI frequence (Hz) + spimaxfrequency Maximum SPI frequence (Hz) - interrupt GPIO for interrupt signal + interrupt GPIO for interrupt signal Name: mcp2515-can1 Info: Configures the MCP2515 CAN controller on spi0.1 Load: dtoverlay=mcp2515-can1,= -Params: oscillator Clock frequency for the CAN controller (Hz) +Params: oscillator Clock frequency for the CAN controller (Hz) - spimaxfrequency Maximum SPI frequence (Hz) + spimaxfrequency Maximum SPI frequence (Hz) - interrupt GPIO for interrupt signal + interrupt GPIO for interrupt signal Name: mmc Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock Load: dtoverlay=mmc,= -Params: overclock_50 Clock (in MHz) to use when the MMC framework - requests 50MHz - force_pio Disable DMA support +Params: overclock_50 Clock (in MHz) to use when the MMC framework + requests 50MHz + force_pio Disable DMA support Name: mz61581 Info: MZ61581 display by Tontec Load: dtoverlay=mz61581,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - txbuflen Transmit buffer length (default 32768) + txbuflen Transmit buffer length (default 32768) - debug Debug output level {0-7} + debug Debug output level {0-7} - xohms Touchpanel sensitivity (X-plate resistance) + xohms Touchpanel sensitivity (X-plate resistance) [ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ] @@ -474,69 +474,69 @@ Params: speed Display Name: piscreen Info: PiScreen display by OzzMaker.com Load: dtoverlay=piscreen,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} - xohms Touchpanel sensitivity (X-plate resistance) + xohms Touchpanel sensitivity (X-plate resistance) Name: piscreen2r Info: PiScreen 2 with resistive TP display by OzzMaker.com Load: dtoverlay=piscreen2r,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} - xohms Touchpanel sensitivity (X-plate resistance) + xohms Touchpanel sensitivity (X-plate resistance) Name: pitft28-capacitive Info: Adafruit PiTFT 2.8" capacitive touch screen Load: dtoverlay=pitft28-capacitive,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} - touch-sizex Touchscreen size x (default 240) + touch-sizex Touchscreen size x (default 240) - touch-sizey Touchscreen size y (default 320) + touch-sizey Touchscreen size y (default 320) - touch-invx Touchscreen inverted x axis + touch-invx Touchscreen inverted x axis - touch-invy Touchscreen inverted y axis + touch-invy Touchscreen inverted y axis - touch-swapxy Touchscreen swapped x y axis + touch-swapxy Touchscreen swapped x y axis Name: pitft28-resistive Info: Adafruit PiTFT 2.8" resistive touch screen Load: dtoverlay=pitft28-resistive,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} Name: pps-gpio Info: Configures the pps-gpio (pulse-per-second time signal via GPIO). Load: dtoverlay=pps-gpio,= -Params: gpiopin Input GPIO (default "18") +Params: gpiopin Input GPIO (default "18") Name: pwm @@ -553,9 +553,9 @@ Info: Configures a single PWM channel 4) Currently the clock must have been enabled and configured by other means. Load: dtoverlay=pwm,= -Params: pin Output pin (default 18) - see table - func Pin function (default 2 = Alt5) - see above - clock PWM clock frequency (informational) +Params: pin Output pin (default 18) - see table + func Pin function (default 2 = Alt5) - see above + clock PWM clock frequency (informational) Name: pwm-2chan @@ -572,11 +572,11 @@ Info: Configures both PWM channels 4) Currently the clock must have been enabled and configured by other means. Load: dtoverlay=pwm-2chan,= -Params: pin Output pin (default 18) - see table - pin2 Output pin for other channel (default 19) - func Pin function (default 2 = Alt5) - see above - func2 Function for pin2 (default 2 = Alt5) - clock PWM clock frequency (informational) +Params: pin Output pin (default 18) - see table + pin2 Output pin for other channel (default 19) + func Pin function (default 2 = Alt5) - see above + func2 Function for pin2 (default 2 = Alt5) + clock PWM clock frequency (informational) Name: raspidac3 @@ -600,15 +600,15 @@ Params: Name: rpi-display Info: RPi-Display - 2.8" Touch Display by Watterott Load: dtoverlay=rpi-display,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} - xohms Touchpanel sensitivity (X-plate resistance) + xohms Touchpanel sensitivity (X-plate resistance) Name: rpi-ft5406 @@ -632,52 +632,52 @@ Params: Name: sdhost Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock Load: dtoverlay=sdhost,= -Params: overclock_50 Clock (in MHz) to use when the MMC framework - requests 50MHz +Params: overclock_50 Clock (in MHz) to use when the MMC framework + requests 50MHz - force_pio Disable DMA support (default off) + force_pio Disable DMA support (default off) - pio_limit Number of blocks above which to use DMA - (default 1) + pio_limit Number of blocks above which to use DMA + (default 1) - debug Enable debug output (default off) + debug Enable debug output (default off) Name: sdio Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock, and enables SDIO via GPIOs 22-27. Load: dtoverlay=sdio,= -Params: overclock_50 SD Clock (in MHz) to use when the MMC framework - requests 50MHz +Params: overclock_50 SD Clock (in MHz) to use when the MMC framework + requests 50MHz - sdio_overclock SDIO Clock (in MHz) to use when the MMC - framework requests 50MHz + sdio_overclock SDIO Clock (in MHz) to use when the MMC + framework requests 50MHz - force_pio Disable DMA support (default off) + force_pio Disable DMA support (default off) - pio_limit Number of blocks above which to use DMA - (default 1) + pio_limit Number of blocks above which to use DMA + (default 1) - debug Enable debug output (default off) + debug Enable debug output (default off) - poll_once Disable SDIO-device polling every second - (default on: polling once at boot-time) + poll_once Disable SDIO-device polling every second + (default on: polling once at boot-time) - bus_width Set the SDIO host bus width (default 4 bits) + bus_width Set the SDIO host bus width (default 4 bits) Name: sdtweak Info: Tunes the bcm2835-sdhost SD/MMC driver Load: dtoverlay=sdtweak,= -Params: overclock_50 Clock (in MHz) to use when the MMC framework - requests 50MHz +Params: overclock_50 Clock (in MHz) to use when the MMC framework + requests 50MHz - force_pio Disable DMA support (default off) + force_pio Disable DMA support (default off) - pio_limit Number of blocks above which to use DMA - (default 1) + pio_limit Number of blocks above which to use DMA + (default 1) - debug Enable debug output (default off) + debug Enable debug output (default off) Name: smi @@ -708,25 +708,25 @@ Name: tinylcd35 Info: 3.5" Color TFT Display by www.tinylcd.com Options: Touch, RTC, keypad Load: dtoverlay=tinylcd35,= -Params: speed Display SPI bus speed +Params: speed Display SPI bus speed - rotate Display rotation {0,90,180,270} + rotate Display rotation {0,90,180,270} - fps Delay between frame updates + fps Delay between frame updates - debug Debug output level {0-7} + debug Debug output level {0-7} - touch Enable touch panel + touch Enable touch panel - touchgpio Touch controller IRQ GPIO + touchgpio Touch controller IRQ GPIO - xohms Touchpanel: Resistance of X-plate in ohms + xohms Touchpanel: Resistance of X-plate in ohms - rtc-pcf PCF8563 Real Time Clock + rtc-pcf PCF8563 Real Time Clock - rtc-ds DS1307 Real Time Clock + rtc-ds DS1307 Real Time Clock - keypad Enable keypad + keypad Enable keypad Examples: Display with touchpanel, PCF8563 RTC and keypad: @@ -738,9 +738,9 @@ Params: speed Display Name: uart1 Info: Enable uart1 in place of uart0 Load: dtoverlay=uart1,= -Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14) +Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14) - rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15) + rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15) Name: vc4-kms-v3d @@ -763,22 +763,22 @@ Name: w1-gpio Info: Configures the w1-gpio Onewire interface module. Use this overlay if you *don't* need a GPIO to drive an external pullup. Load: dtoverlay=w1-gpio,= -Params: gpiopin GPIO for I/O (default "4") +Params: gpiopin GPIO for I/O (default "4") - pullup Non-zero, "on", or "y" to enable the parasitic - power (2-wire, power-on-data) feature + pullup Non-zero, "on", or "y" to enable the parasitic + power (2-wire, power-on-data) feature Name: w1-gpio-pullup Info: Configures the w1-gpio Onewire interface module. Use this overlay if you *do* need a GPIO to drive an external pullup. Load: dtoverlay=w1-gpio-pullup,= -Params: gpiopin GPIO for I/O (default "4") +Params: gpiopin GPIO for I/O (default "4") - pullup Non-zero, "on", or "y" to enable the parasitic - power (2-wire, power-on-data) feature + pullup Non-zero, "on", or "y" to enable the parasitic + power (2-wire, power-on-data) feature - extpullup GPIO for external pullup (default "5") + extpullup GPIO for external pullup (default "5") Troubleshooting