#include "qcom-ipq8065-v1.0.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "ZyXEL NBG6817";
compatible = "zyxel,nbg6817", "qcom,ipq8065";
memory@0 {
reg = <0x42000000 0x1e000000>;
device_type = "memory";
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
rsvd@41200000 {
reg = <0x41200000 0x300000>;
no-map;
};
};
aliases {
serial0 = &gsbi4_serial;
mdio-gpio0 = &mdio0;
sdcc1 = &sdcc1;
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-upgrade = &power;
};
chosen {
bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
linux,stdout-path = "serial0:115200n8";
};
soc {
pinmux@800000 {
button_pins: button_pins {
mux {
pins = "gpio6", "gpio54", "gpio65";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
i2c4_pins: i2c4_pinmux {
mux {
pins = "gpio12", "gpio13";
function = "gsbi4";
drive-strength = <12>;
bias-disable;
};
};
led_pins: led_pins {
mux {
pins = "gpio9", "gpio26", "gpio33", "gpio64";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
};
mdio0_pins: mdio0_pins {
mux {
pins = "gpio0", "gpio1";
function = "gpio";
drive-strength = <8>;
bias-disable;
};
clk {
pins = "gpio1";
input-disable;
};
};
rgmii2_pins: rgmii2_pins {
mux {
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
function = "rgmii2";
drive-strength = <8>;
bias-disable;
};
tx {
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
input-disable;
};
};
spi_pins: spi_pins {
mux {
pins = "gpio18", "gpio19", "gpio21";
function = "gsbi5";
drive-strength = <10>;
bias-none;
};
cs {
pins = "gpio20";
drive-strength = <12>;
};
};
usb0_pwr_en_pins: usb0_pwr_en_pins {
mux {
pins = "gpio16", "gpio17";
function = "gpio";
drive-strength = <12>;
};
pwr {
pins = "gpio17";
bias-pull-down;
output-high;
};
ovc {
pins = "gpio16";
bias-pull-up;
};
};
usb1_pwr_en_pins: usb1_pwr_en_pins {
mux {
pins = "gpio14", "gpio15";
function = "gpio";
drive-strength = <12>;
};
pwr {
pins = "gpio14";
bias-pull-down;
output-high;
};
ovc {
pins = "gpio15";
bias-pull-up;
};
};
};
gsbi@16300000 {
qcom,mode = <GSBI_PROT_I2C_UART>;
status = "ok";
serial@16340000 {
status = "ok";
};
/*
* The i2c device on gsbi4 should not be enabled.
* On ipq806x designs gsbi4 i2c is meant for exclusive
* RPM usage. Turning this on in kernel manifests as
* i2c failure for the RPM.
*/
};
gsbi5: gsbi@1a200000 {
qcom,mode = <GSBI_PROT_SPI>;
status = "ok";
spi4: spi@1a280000 {
status = "ok";
pinctrl-0 = <&spi_pins>;
pinctrl-names = "default";
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
flash: m25p80@0 {
compatible = "jedec,spi-nor";
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <51200000>;
reg = <0>;
linux,part-probe = "qcom-smem";
};
};
};
phy@100f8800 { /* USB3 port 1 HS phy */
status = "ok";
};
phy@100f8830 { /* USB3 port 1 SS phy */
status = "ok";
};
phy@110f8800 { /* USB3 port 0 HS phy */
status = "ok";
};
phy@110f8830 { /* USB3 port 0 SS phy */
status = "ok";
};
usb30@0 {
status = "ok";
pinctrl-0 = <&usb0_pwr_en_pins>;
pinctrl-names = "default";
};
usb30@1 {
status = "ok";
pinctrl-0 = <&usb1_pwr_en_pins>;
pinctrl-names = "default";
};
pcie0: pci@1b500000 {
status = "ok";
reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_pins>;
pinctrl-names = "default";
};
pcie1: pci@1b700000 {
status = "ok";
reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_pins>;
pinctrl-names = "default";
};
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&mdio0_pins>;
pinctrl-names = "default";
phy0: ethernet-phy@0 {
device_type = "ethernet-phy";
reg = <0>;
qca,ar8327-initvals = <
0x00004 0x7600000 /* PAD0_MODE */
0x00008 0x1000000 /* PAD5_MODE */
0x0000c 0x80 /* PAD6_MODE */
0x000e4 0xaa545 /* MAC_POWER_SEL */
0x000e0 0xc74164de /* SGMII_CTRL */
0x0007c 0x4e /* PORT0_STATUS */
0x00094 0x4e /* PORT6_STATUS */
0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
0x00978 0x19008643 /* QM_PORT1_CTRL0 */
0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
0x00980 0x19008643 /* QM_PORT2_CTRL0 */
0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
0x00988 0x19008643 /* QM_PORT3_CTRL0 */
0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
0x00990 0x19008643 /* QM_PORT4_CTRL0 */
0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
>;
};
phy4: ethernet-phy@4 {
device_type = "ethernet-phy";
reg = <4>;
qca,ar8327-initvals = <
0x000e4 0x6a545 /* MAC_POWER_SEL */
0x0000c 0x80 /* PAD6_MODE */
>;
};
};
gmac1: ethernet@37200000 {
status = "ok";
phy-mode = "rgmii";
qcom,id = <1>;
qcom,phy_mdio_addr = <4>;
qcom,poll_required = <0>;
qcom,rgmii_delay = <1>;
qcom,phy_mii_type = <0>;
qcom,emulation = <0>;
qcom,irq = <255>;
mdiobus = <&mdio0>;
pinctrl-0 = <&rgmii2_pins>;
pinctrl-names = "default";
fixed-link {
speed = <1000>;
full-duplex;
};
};
gmac2: ethernet@37400000 {
status = "ok";
phy-mode = "sgmii";
qcom,id = <2>;
qcom,phy_mdio_addr = <0>; /* none */
qcom,poll_required = <0>; /* no polling */
qcom,rgmii_delay = <0>;
qcom,phy_mii_type = <1>;
qcom,emulation = <0>;
qcom,irq = <258>;
mdiobus = <&mdio0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
rpm@108000 {
pinctrl-0 = <&i2c4_pins>;
pinctrl-names = "default";
};
amba {
sdcc1: sdcc@12400000 {
status = "okay";
};
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&button_pins>;
pinctrl-names = "default";
wifi {
label = "wifi";
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
reset {
label = "reset";
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&led_pins>;
pinctrl-names = "default";
internet {
label = "nbg6817:white:internet";
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
};
power: power {
label = "nbg6817:white:power";
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
default-state = "keep";
};
wifi2g {
label = "nbg6817:amber:wifi2g";
gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
};
/* wifi2g amber from the manual is missing */
wifi5g {
label = "nbg6817:amber:wifi5g";
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
};
/* wifi5g amber from the manual is missing */
};
};
&adm_dma {
status = "ok";
};