1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
The network configuration in Kamikaze is stored in \texttt{/etc/config/network}
and is divided into interface configurations.
Each interface configuration either refers directly to an ethernet/wifi
interface (\texttt{eth0}, \texttt{wl0}, ..) or to a bridge containing multiple interfaces.
It looks like this:
\begin{Verbatim}
config interface "lan"
option ifname "eth0"
option proto "static"
option ipaddr "192.168.1.1"
option netmask "255.255.255.0"
option gateway "192.168.1.254"
option dns "192.168.1.254"
\end{Verbatim}
\texttt{ifname} specifies the Linux interface name.
If you want to use bridging on one or more interfaces, set \texttt{ifname} to a list
of interfaces and add:
\begin{Verbatim}
option type "bridge"
\end{Verbatim}
It is possible to use VLAN tagging on an interface simply by adding the VLAN IDs
to it, e.g. \texttt{eth0.1}. These can be nested as well.
This sets up a simple static configuration for \texttt{eth0}. \texttt{proto} specifies the
protocol used for the interface. The default image usually provides \texttt{'none'}
\texttt{'static'}, \texttt{'dhcp'} and \texttt{'pppoe'}. Others can be added by installing additional
packages.
When using the \texttt{'static'} method like in the example, the options \texttt{ipaddr} and
\texttt{netmask} are mandatory, while \texttt{gateway} and \texttt{dns} are optional.
You can specify more than one DNS server, separated with spaces.
DHCP currently only accepts \texttt{ipaddr} (IP address to request from the server)
and \texttt{hostname} (client hostname identify as) - both are optional.
PPP based protocols (\texttt{pppoe}, \texttt{pptp}, ...) accept these options:
\begin{itemize}
\item{username} \\
The PPP username (usually with PAP authentication)
\item{password} \\
The PPP password
\item{keepalive} \\
Ping the PPP server (using LCP). The value of this option
specifies the maximum number of failed pings before reconnecting.
The ping interval defaults to 5, but can be changed by appending
",<interval>" to the keepalive value
\item{demand} \\
Use Dial on Demand (value specifies the maximum idle time.
\item{server: (pptp)} \\
The remote pptp server IP
\end{itemize}
For all protocol types, you can also specify the MTU by using the \texttt{mtu} option.
\subsubsection{Setting up static routes}
You can set up static routes for a specific interface that will be brought up
after the interface is configured.
Simply add a config section like this:
\begin{Verbatim}
config route foo
option interface lan
option target 1.1.1.0
option netmask 255.255.255.0
option gateway 192.168.1.1
\end{Verbatim}
The name for the route section is optional, the \texttt{interface}, \texttt{target} and
\texttt{gateway} options are mandatory.
Leaving out the \texttt{netmask} option will turn the route into a host route.
\subsubsection{Setting up the switch (currently broadcom only)}
The switch configuration is set by adding a \texttt{'switch'} config section.
Example:
\begin{Verbatim}
config switch "eth0"
option vlan0 "1 2 3 4 5*"
option vlan1 "0 5"
\end{Verbatim}
On Broadcom hardware the section name needs to be eth0, as the switch driver
does not detect the switch on any other physical device.
Every vlan option needs to have the name vlan<n> where <n> is the VLAN number
as used in the switch driver.
As value it takes a list of ports with these optional suffixes:
\begin{itemize}
\item{\texttt{'*'}:}
Set the default VLAN (PVID) of the Port to the current VLAN
\item{\texttt{'u'}:}
Force the port to be untagged
\item{\texttt{'t'}:}
Force the port to be tagged
\end{itemize}
The CPU port defaults to tagged, all other ports to untagged.
On Broadcom hardware the CPU port is always 5. The other ports may vary with
different hardware.
For instance, if you wish to have 3 vlans, like one 3-port switch, 1 port in a
DMZ, and another one as your WAN interface, use the following configuration :
\begin{Verbatim}
config switch "eth0"
option vlan0 "1 2 3 5*"
option vlan1 "0 5"
option vlan2 "4 5"
\end{Verbatim}
\subsubsection{Setting up IPv6 connectivity}
OpenWrt supports IPv6 connectivity using PPP, Tunnel brokers or static
assignment.
If you use PPP, IPv6 will be setup using IP6CP and there is nothing to
configure.
To setup an IPv6 tunnel to a tunnel broker, you have to edit the
\texttt{/etc/config/6tunnel} file and change the settings accordingly :
\begin{Verbatim}
config 6tunnel
option tnlifname 'sixbone'
option remoteip4 '1.0.0.1'
option localip4 '1.0.0.2'
option localip6 '2001::DEAD::BEEF::1'
option prefix '/64'
\end{Verbatim}
\begin{itemize}
\item{\texttt{'tnlifname'}:}
Set the interface name of the IPv6 in IPv4 tunnel
\item{\texttt{'remoteip4'}:}
IP address of the remote end to establish the 6in4 tunnel.
This address is given by the tunnel broker
\item{\texttt{'localip4'}:}
IP address of your router to establish the 6in4 tunnel.
It will usually match your WAN IP address.
\item{\texttt{'localip6'}:}
IPv6 address to setup on your tunnel side
This address is given by the tunnel broker
\item{\texttt{'prefix'}:}
IPv6 prefix to setup on the LAN.
\end{itemize}
IPv6 static addressing is also supported using a similar setup as
IPv4 but with the \texttt{ip6} prefixing (when applicable).
\begin{Verbatim}
config interface "lan"
option ifname "eth0"
option proto "static"
option ip6addr "fe80::200:ff:fe00:0/64"
\end{Verbatim}
|
