summaryrefslogtreecommitdiff
path: root/target/linux/brcm2708/patches-4.1/0098-BCM270X_DT-Add-overlay-to-enable-uart1.patch
blob: ccf68356961c0600f5089c079e242177ef6a002e (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
From 98e84cdbce80fe8a8177fb1f42800af76b3da9ac Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Fri, 26 Jun 2015 08:50:11 +0100
Subject: [PATCH 098/171] BCM270X_DT: Add overlay to enable uart1

N.B. The UART1 clock is derived from the core clock. The firmware
will update clock-frequency if core_freq is set, but be aware
that unless force_turbo=1 while overclocking then the baud rate
will vary with ARM activity.
---
 arch/arm/boot/dts/bcm2708-rpi-b-plus.dts     |  1 +
 arch/arm/boot/dts/bcm2708-rpi-b.dts          |  1 +
 arch/arm/boot/dts/bcm2708-rpi-cm.dts         |  1 +
 arch/arm/boot/dts/bcm2709-rpi-2-b.dts        |  1 +
 arch/arm/boot/dts/overlays/Makefile          |  1 +
 arch/arm/boot/dts/overlays/README            |  8 ++++++
 arch/arm/boot/dts/overlays/uart1-overlay.dts | 38 ++++++++++++++++++++++++++++
 arch/arm/configs/bcm2709_defconfig           |  2 +-
 arch/arm/configs/bcmrpi_defconfig            |  2 +-
 9 files changed, 53 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/boot/dts/overlays/uart1-overlay.dts

--- a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
@@ -103,6 +103,7 @@
 	__overrides__ {
 		uart0 = <&uart0>,"status";
 		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
 		i2s = <&i2s>,"status";
 		spi = <&spi0>,"status";
 		i2c0 = <&i2c0>,"status";
--- a/arch/arm/boot/dts/bcm2708-rpi-b.dts
+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
@@ -97,6 +97,7 @@
 	__overrides__ {
 		uart0 = <&uart0>,"status";
 		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
 		i2s = <&i2s>,"status";
 		spi = <&spi0>,"status";
 		i2c0 = <&i2c0>,"status";
--- a/arch/arm/boot/dts/bcm2708-rpi-cm.dts
+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts
@@ -79,6 +79,7 @@
 	__overrides__ {
 		uart0 = <&uart0>,"status";
 		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
 		i2s = <&i2s>,"status";
 		spi = <&spi0>,"status";
 		i2c0 = <&i2c0>,"status";
--- a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
@@ -103,6 +103,7 @@
 	__overrides__ {
 		uart0 = <&uart0>,"status";
 		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
 		i2s = <&i2s>,"status";
 		spi = <&spi0>,"status";
 		i2c0 = <&i2c0>,"status";
--- a/arch/arm/boot/dts/overlays/Makefile
+++ b/arch/arm/boot/dts/overlays/Makefile
@@ -42,6 +42,7 @@ dtb-$(RPI_DT_OVERLAYS) += sdhost-overlay
 dtb-$(RPI_DT_OVERLAYS) += spi-bcm2708-overlay.dtb
 dtb-$(RPI_DT_OVERLAYS) += spi-bcm2835-overlay.dtb
 dtb-$(RPI_DT_OVERLAYS) += tinylcd35-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += uart1-overlay.dtb
 dtb-$(RPI_DT_OVERLAYS) += w1-gpio-overlay.dtb
 dtb-$(RPI_DT_OVERLAYS) += w1-gpio-pullup-overlay.dtb
 
--- a/arch/arm/boot/dts/overlays/README
+++ b/arch/arm/boot/dts/overlays/README
@@ -489,6 +489,14 @@ Params: speed                    Display
                 dtoverlay=tinylcd35,touch,touchgpio=3
 
 
+Name:   uart1
+Info:   Enable uart1 in place of uart0
+Load:   dtoverlay=uart1,<param>=<val>
+Params: txd1_pin                 GPIO pin for TXD1 (14, 32 or 40 - default 14)
+
+        rxd1_pin                 GPIO pin for RXD1 (15, 33 or 41 - default 15)
+
+
 Name:   w1-gpio
 Info:   Configures the w1-gpio Onewire interface module.
         Use this overlay if you *don't* need a GPIO to drive an external pullup.
--- /dev/null
+++ b/arch/arm/boot/dts/overlays/uart1-overlay.dts
@@ -0,0 +1,38 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&uart1>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			uart1_pins: uart1_pins {
+				brcm,pins = <14 15>;
+				brcm,function = <2>; /* alt5 */
+				brcm,pull = <0 2>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target-path = "/chosen";
+		__overlay__ {
+			bootargs = "8250.nr_uarts=1";
+		};
+	};
+
+	__overrides__ {
+		txd1_pin = <&uart1_pins>,"brcm,pins:0";
+		rxd1_pin = <&uart1_pins>,"brcm,pins:4";
+	};
+};
--- a/arch/arm/configs/bcm2709_defconfig
+++ b/arch/arm/configs/bcm2709_defconfig
@@ -562,7 +562,7 @@ CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 # CONFIG_SERIAL_8250_DMA is not set
 CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+CONFIG_SERIAL_8250_RUNTIME_UARTS=0
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y
--- a/arch/arm/configs/bcmrpi_defconfig
+++ b/arch/arm/configs/bcmrpi_defconfig
@@ -555,7 +555,7 @@ CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 # CONFIG_SERIAL_8250_DMA is not set
 CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+CONFIG_SERIAL_8250_RUNTIME_UARTS=0
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y