1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
Index: linux-4.3/drivers/thermal/imx_thermal.c
===================================================================
--- linux-4.3.orig/drivers/thermal/imx_thermal.c 2015-11-01 16:05:25.000000000 -0800
+++ linux-4.3/drivers/thermal/imx_thermal.c 2015-12-18 10:39:44.915158318 -0800
@@ -55,6 +55,7 @@
#define TEMPSENSE2_PANIC_VALUE_SHIFT 16
#define TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
+#define OCOTP_MEM0 0x0480
#define OCOTP_ANA1 0x04e0
/* The driver supports 1 passive trip point and 1 critical trip point */
@@ -64,12 +65,6 @@
IMX_TRIP_NUM,
};
-/*
- * It defines the temperature in millicelsius for passive trip point
- * that will trigger cooling action when crossed.
- */
-#define IMX_TEMP_PASSIVE 85000
-
#define IMX_POLLING_DELAY 2000 /* millisecond */
#define IMX_PASSIVE_DELAY 1000
@@ -100,12 +95,14 @@
u32 c1, c2; /* See formula in imx_get_sensor_data() */
int temp_passive;
int temp_critical;
+ unsigned long temp_max;
int alarm_temp;
int last_temp;
bool irq_enabled;
int irq;
struct clk *thermal_clk;
const struct thermal_soc_data *socdata;
+ const char *temp_grade;
};
static void imx_set_panic_temp(struct imx_thermal_data *data,
@@ -285,10 +282,12 @@
{
struct imx_thermal_data *data = tz->devdata;
+ /* do not allow changing critical threshold */
if (trip == IMX_TRIP_CRITICAL)
return -EPERM;
- if (temp > IMX_TEMP_PASSIVE)
+ /* do not allow passive to be set higher than critical */
+ if (temp < 0 || temp > data->temp_critical)
return -EINVAL;
data->temp_passive = temp;
@@ -404,17 +403,39 @@
data->c1 = temp64;
data->c2 = n1 * data->c1 + 1000 * t1;
- /*
- * Set the default passive cooling trip point,
- * can be changed from userspace.
- */
- data->temp_passive = IMX_TEMP_PASSIVE;
+ /* use OTP for thermal grade */
+ ret = regmap_read(map, OCOTP_MEM0, &val);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to read temp grade: %d\n", ret);
+ return ret;
+ }
+
+ /* The maximum die temp is specified by the Temperature Grade */
+ switch ((val >> 6) & 0x3) {
+ case 0: /* Commercial (0 to 95C) */
+ data->temp_grade = "Commercial";
+ data->temp_max = 95000;
+ break;
+ case 1: /* Extended Commercial (-20 to 105C) */
+ data->temp_grade = "Extended Commercial";
+ data->temp_max = 105000;
+ break;
+ case 2: /* Industrial (-40 to 105C) */
+ data->temp_grade = "Industrial";
+ data->temp_max = 105000;
+ break;
+ case 3: /* Automotive (-40 to 125C) */
+ data->temp_grade = "Automotive";
+ data->temp_max = 125000;
+ break;
+ }
/*
- * The maximum die temperature set to 20 C higher than
- * IMX_TEMP_PASSIVE.
+ * Set the critical trip point at 5C under max
+ * Set the passive trip point at 10C under max (can change via sysfs)
*/
- data->temp_critical = 1000 * 20 + data->temp_passive;
+ data->temp_critical = data->temp_max - (1000 * 5);
+ data->temp_passive = data->temp_max - (1000 * 10);
return 0;
}
@@ -559,6 +580,11 @@
return ret;
}
+ dev_info(&pdev->dev, "%s CPU temperature grade - max:%ldC"
+ " critical:%ldC passive:%ldC\n", data->temp_grade,
+ data->temp_max / 1000, data->temp_critical / 1000,
+ data->temp_passive / 1000);
+
/* Enable measurements at ~ 10 Hz */
regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
|
