ar71xx: add support for jjPlus JWAP230

jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers

Default configuration:

- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space

Flash instruction (do it under U-Boot, using RS232):

1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

4 files changed, 169 insertions, 0 deletions

diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index 9ab6fed..b0eada1 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -680,6 +680,15 @@ config ATH79_MACH_JWAP003
 	select ATH79_DEV_M25P80
 	select ATH79_DEV_USB
 
+config ATH79_MACH_JWAP230
+	bool "jjPlus JWAP230 board support"
+	select SOC_QCA955X
+	select ATH79_DEV_ETH
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+
 config ATH79_MACH_WRT160NL
 	bool "Linksys WRT160NL board support"
 	select SOC_AR913X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 33c274f..390b17d 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -100,6 +100,7 @@ obj-$(CONFIG_ATH79_MACH_GS_OOLITE)	+= mach-gs-oolite.o
 obj-$(CONFIG_ATH79_MACH_HIWIFI_HC6361)	+= mach-hiwifi-hc6361.o
 obj-$(CONFIG_ATH79_MACH_JA76PF)		+= mach-ja76pf.o
 obj-$(CONFIG_ATH79_MACH_JWAP003)	+= mach-jwap003.o
+obj-$(CONFIG_ATH79_MACH_JWAP230)	+= mach-jwap230.o
 obj-$(CONFIG_ATH79_MACH_HORNET_UB)	+= mach-hornet-ub.o
 obj-$(CONFIG_ATH79_MACH_MC_MAC1200R)     += mach-mc-mac1200r.o
 obj-$(CONFIG_ATH79_MACH_MR12)		+= mach-mr12.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-jwap230.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-jwap230.c
new file mode 100644
index 0000000..f94e5b4
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-jwap230.c
@@ -0,0 +1,158 @@
+/*
+ * jjPlus JWAP230 board support
+ *
+ * Copyright (C) 2016 Piotr Dymacz <pepe2k@gmail.com>
+ *
+ * Based on mach-wpj558.c and mach-tl-wr1043nd-v2.c
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/pci.h>
+#include <linux/phy.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/ar8216_platform.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define JWAP230_GPIO_LED_LED1		23
+#define JWAP230_GPIO_LED_LED2		22
+#define JWAP230_GPIO_LED_LED3		21
+
+#define JWAP230_MAC0_OFFSET		0x0
+#define JWAP230_MAC1_OFFSET		0x6
+#define JWAP230_WMAC_CALDATA_OFFSET	0x1000
+
+static struct gpio_led jwap230_leds_gpio[] __initdata = {
+	{
+		.name		= "jwap230:green:led1",
+		.gpio		= JWAP230_GPIO_LED_LED1,
+		.active_low	= 1,
+	},
+	{
+		.name		= "jwap230:green:led2",
+		.gpio		= JWAP230_GPIO_LED_LED2,
+		.active_low	= 1,
+	},
+	{
+		.name		= "jwap230:green:led3",
+		.gpio		= JWAP230_GPIO_LED_LED3,
+		.active_low	= 1,
+	}
+};
+
+static const struct ar8327_led_info jwap230_leds_qca8337[] = {
+	AR8327_LED_INFO(PHY0_0, HW, "jwap230:green:lan"),
+	AR8327_LED_INFO(PHY4_0, HW, "jwap230:green:wan"),
+};
+
+/* Blink rate: 1 Gbps -> 8 hz, 100 Mbs -> 4 Hz, 10 Mbps -> 2 Hz */
+static struct ar8327_led_cfg jwap230_qca8337_led_cfg = {
+	.led_ctrl0 = 0xcf37cf37,
+	.led_ctrl1 = 0xcf37cf37,
+	.led_ctrl2 = 0xcf37cf37,
+	.led_ctrl3 = 0x0,
+	.open_drain = true,
+};
+
+/* QCA8337 GMAC0 is connected with QCA9558 over RGMII */
+static struct ar8327_pad_cfg jwap230_qca8337_pad0_cfg = {
+	.mode = AR8327_PAD_MAC_RGMII,
+	.txclk_delay_en = true,
+	.rxclk_delay_en = true,
+	.txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
+	.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
+	.mac06_exchange_dis = true,
+};
+
+/* QCA8337 GMAC6 is connected with QCA9558 over SGMII */
+static struct ar8327_pad_cfg jwap230_qca8337_pad6_cfg = {
+	.mode = AR8327_PAD_MAC_SGMII,
+	.sgmii_delay_en = true,
+	.rxclk_delay_sel = AR8327_CLK_DELAY_SEL0,
+};
+
+static struct ar8327_platform_data jwap230_qca8337_data = {
+	.pad0_cfg = &jwap230_qca8337_pad0_cfg,
+	.pad6_cfg = &jwap230_qca8337_pad6_cfg,
+	.port0_cfg = {
+		.force_link = 1,
+		.speed = AR8327_PORT_SPEED_1000,
+		.duplex = 1,
+		.txpause = 1,
+		.rxpause = 1,
+	},
+	.port6_cfg = {
+		.force_link = 1,
+		.speed = AR8327_PORT_SPEED_1000,
+		.duplex = 1,
+		.txpause = 1,
+		.rxpause = 1,
+	},
+	.led_cfg = &jwap230_qca8337_led_cfg,
+	.num_leds = ARRAY_SIZE(jwap230_leds_qca8337),
+	.leds = jwap230_leds_qca8337,
+};
+
+static struct mdio_board_info jwap230_mdio0_info[] = {
+	{
+		.bus_id = "ag71xx-mdio.0",
+		.phy_addr = 0,
+		.platform_data = &jwap230_qca8337_data,
+	},
+};
+
+static void __init jwap230_setup(void)
+{
+	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+
+	ath79_register_m25p80(NULL);
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(jwap230_leds_gpio),
+				 jwap230_leds_gpio);
+
+	mdiobus_register_board_info(jwap230_mdio0_info,
+				    ARRAY_SIZE(jwap230_mdio0_info));
+	ath79_register_mdio(0, 0x0);
+
+	ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN);
+
+	/* QCA9558 GMAC0 is connected to RMGII interface */
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+	ath79_eth0_data.phy_mask = BIT(0);
+	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+	ath79_eth0_pll_data.pll_1000 = 0xa6000000;
+
+	ath79_init_mac(ath79_eth0_data.mac_addr, art + JWAP230_MAC0_OFFSET, 0);
+	ath79_register_eth(0);
+
+	/* QCA9558 GMAC1 is connected to SGMII interface */
+	ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+	ath79_eth1_data.speed = SPEED_1000;
+	ath79_eth1_data.duplex = DUPLEX_FULL;
+	ath79_eth1_pll_data.pll_1000 = 0x03000101;
+
+	ath79_init_mac(ath79_eth1_data.mac_addr, art + JWAP230_MAC1_OFFSET, 0);
+	ath79_register_eth(1);
+
+	ath79_register_wmac(art + JWAP230_WMAC_CALDATA_OFFSET, NULL);
+
+	ath79_register_pci();
+	ath79_register_usb();
+}
+
+MIPS_MACHINE(ATH79_MACH_JWAP230, "JWAP230", "jjPlus JWAP230", jwap230_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 3425ce9..7dd60ac 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -94,6 +94,7 @@ enum ath79_mach_type {
 	ATH79_MACH_JA76PF,		/* jjPlus JA76PF */
 	ATH79_MACH_JA76PF2,		/* jjPlus JA76PF2 */
 	ATH79_MACH_JWAP003,		/* jjPlus JWAP003 */
+	ATH79_MACH_JWAP230,		/* jjPlus JWAP230 */
 	ATH79_MACH_HORNET_UB,		/* ALFA Networks Hornet-UB */
 	ATH79_MACH_MR12,		/* Cisco Meraki MR12 */
 	ATH79_MACH_MR16,		/* Cisco Meraki MR16 */