ipq806x: Add support for IPQ806x chip family

Patches are generated using the "format-patch" command from the
following location:
*https://www.codeaurora.org/cgit/quic/kernel/galak-msm/log/?h=apq_ipq_base
*rev=0771849495b4128cac2faf7d49c85c729fc48b20
Patches numbered 76/77/102/103 have already been integrated in 3.14.12,
so they're not in this list.

All these patches are either integrated are pending integration into
kernel.org, therefore these patches should go away once the kernel
gets upgraded to 3.16.

Support is currently limited to AP148 board but can be extended to other
platforms in the future.

These changes do not cover ethernet connectivity.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 42334

1 files changed, 179 insertions, 0 deletions

diff --git a/target/linux/ipq806x/patches/0139-ARM-dts-msm-Add-PCIe-related-nodes-for-IPQ8064-AP148.patch b/target/linux/ipq806x/patches/0139-ARM-dts-msm-Add-PCIe-related-nodes-for-IPQ8064-AP148.patch
new file mode 100644
index 0000000..1105f14
--- /dev/null
+++ b/target/linux/ipq806x/patches/0139-ARM-dts-msm-Add-PCIe-related-nodes-for-IPQ8064-AP148.patch
@@ -0,0 +1,179 @@
+From 7c6525a0d5cf88f9244187fbe8ee293fa4ee43c1 Mon Sep 17 00:00:00 2001
+From: Kumar Gala <galak@codeaurora.org>
+Date: Mon, 12 May 2014 19:36:23 -0500
+Subject: [PATCH 139/182] ARM: dts: msm: Add PCIe related nodes for
+ IPQ8064/AP148
+
+---
+ arch/arm/boot/dts/qcom-ipq8064-ap148.dts |   38 ++++++++++++
+ arch/arm/boot/dts/qcom-ipq8064.dtsi      |   93 ++++++++++++++++++++++++++++++
+ 2 files changed, 131 insertions(+)
+
+diff --git a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+index 158a09f..11f7a77 100644
+--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
++++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+@@ -21,6 +21,22 @@
+ 				bias-disable;
+ 			};
+ 
++			pcie1_pins: pcie1_pinmux {
++				mux {
++					pins = "gpio3";
++					drive-strength = <2>;
++					bias-disable;
++				};
++			};
++
++			pcie2_pins: pcie2_pinmux {
++				mux {
++					pins = "gpio48";
++					drive-strength = <2>;
++					bias-disable;
++				};
++			};
++
+ 			spi_pins: spi_pins {
+ 				mux {
+ 					pins = "gpio18", "gpio19", "gpio21";
+@@ -80,5 +96,27 @@
+ 				};
+ 			};
+ 		};
++
++		pci@1b500000 {
++			status = "ok";
++			reset-gpio = <&qcom_pinmux 3 0>;
++			pinctrl-0 = <&pcie1_pins>;
++			pinctrl-names = "default";
++
++			ranges = <0x00000000 0 0x00000000 0x0ff00000 0 0x00100000   /* configuration space */
++				  0x81000000 0 0	  0x0fe00000 0 0x00100000   /* downstream I/O */
++				  0x82000000 0 0x00000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
++		};
++
++		pci@1b700000 {
++			status = "ok";
++			reset-gpio = <&qcom_pinmux 48 0>;
++			pinctrl-0 = <&pcie2_pins>;
++			pinctrl-names = "default";
++
++			ranges = <0x00000000 0 0x00000000 0x31f00000 0 0x00100000   /* configuration space */
++				  0x81000000 0 0	  0x31e00000 0 0x00100000   /* downstream I/O */
++				  0x82000000 0 0x00000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
++		};
+ 	};
+ };
+diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+index 244f857..42a651f 100644
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -2,6 +2,7 @@
+ 
+ #include "skeleton.dtsi"
+ #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
++#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
+ #include <dt-bindings/soc/qcom,gsbi.h>
+ 
+ / {
+@@ -246,5 +247,97 @@
+ 			#clock-cells = <1>;
+ 			#reset-cells = <1>;
+ 		};
++
++		pci@1b500000 {
++			compatible = "qcom,pcie-ipq8064";
++			reg = <0x1b500000 0x1000
++			       0x1b502000 0x80
++			       0x1b600000 0x100
++				>;
++			reg-names = "base", "elbi", "parf";
++
++			#address-cells = <3>;
++			#size-cells = <2>;
++			device_type = "pci";
++			interrupts = <0 35 0x0
++				      0 36 0x0
++				      0 37 0x0
++				      0 38 0x0
++				      0 39 0x0>;
++			resets = <&gcc PCIE_ACLK_RESET>,
++				 <&gcc PCIE_HCLK_RESET>,
++				 <&gcc PCIE_POR_RESET>,
++				 <&gcc PCIE_PCI_RESET>,
++				 <&gcc PCIE_PHY_RESET>;
++			reset-names = "axi", "ahb", "por", "pci", "phy";
++
++			clocks = <&gcc PCIE_A_CLK>,
++				 <&gcc PCIE_H_CLK>,
++				 <&gcc PCIE_PHY_CLK>;
++			clock-names = "core", "iface", "phy";
++			status = "disabled";
++		};
++
++		pci@1b700000 {
++			compatible = "qcom,pcie-ipq8064";
++			reg = <0x1b700000 0x1000
++			       0x1b702000 0x80
++			       0x1b800000 0x100
++				>;
++			reg-names = "base", "elbi", "parf";
++
++			#address-cells = <3>;
++			#size-cells = <2>;
++			device_type = "pci";
++
++			interrupts = <0 57 0x0
++				      0 58 0x0
++				      0 59 0x0
++				      0 60 0x0
++				      0 61 0x0>;
++			resets = <&gcc PCIE_1_ACLK_RESET>,
++				 <&gcc PCIE_1_HCLK_RESET>,
++				 <&gcc PCIE_1_POR_RESET>,
++				 <&gcc PCIE_1_PCI_RESET>,
++				 <&gcc PCIE_1_PHY_RESET>;
++			reset-names = "axi", "ahb", "por", "pci", "phy";
++
++			clocks = <&gcc PCIE_1_A_CLK>,
++				 <&gcc PCIE_1_H_CLK>,
++				 <&gcc PCIE_1_PHY_CLK>;
++			clock-names = "core", "iface", "phy";
++			status = "disabled";
++		};
++
++		pci@1b900000 {
++			compatible = "qcom,pcie-ipq8064";
++			reg = <0x1b900000 0x1000
++			       0x1b902000 0x80
++			       0x1ba00000 0x100
++				>;
++			reg-names = "base", "elbi", "parf";
++
++			#address-cells = <3>;
++			#size-cells = <2>;
++			device_type = "pci";
++
++			interrupts = <0 71 0x0
++				      0 72 0x0
++				      0 73 0x0
++				      0 74 0x0
++				      0 75 0x0>;
++			resets = <&gcc PCIE_2_ACLK_RESET>,
++				 <&gcc PCIE_2_HCLK_RESET>,
++				 <&gcc PCIE_2_POR_RESET>,
++				 <&gcc PCIE_2_PCI_RESET>,
++				 <&gcc PCIE_2_PHY_RESET>;
++			reset-names = "axi", "ahb", "por", "pci", "phy";
++
++			clocks = <&gcc PCIE_2_A_CLK>,
++				 <&gcc PCIE_2_H_CLK>,
++				 <&gcc PCIE_2_PHY_CLK>;
++			clock-names = "core", "iface", "phy";
++			status = "disabled";
++		};
+ 	};
+ };
+-- 
+1.7.10.4
+