target/linux : drop many arch

8 files changed, 0 insertions, 374 deletions

diff --git a/target/linux/lantiq/base-files/etc/diag.sh b/target/linux/lantiq/base-files/etc/diag.sh
deleted file mode 100644
index 26f0a3c..0000000
--- a/target/linux/lantiq/base-files/etc/diag.sh
+++ /dev/null
@@ -1,42 +0,0 @@
-#!/bin/sh
-# Copyright (C) 2012-2013 OpenWrt.org
-
-. /lib/functions/leds.sh
-
-status_led="power"
-
-set_state() {
-	[ -d /sys/class/leds/power2/ ] && {
-
-		case "$1" in
-		preinit)
-			led_set_attr "power2" "trigger" "heartbeat"
-			status_led_on
-			;;
-		failsafe)
-			led_off "power2"
-			status_led_set_timer 100 100
-			;;
-		done)
-			led_off "power2"
-			;;
-		esac
-		return
-	}
-
-	case "$1" in
-	preinit)
-		status_led_set_heartbeat
-		;;
-	failsafe)
-		[ -d /sys/class/leds/power1 ] && {
-			status_led_off
-			led_timer "power1" 100 100
-		} || status_led_set_timer 100 100
-		;;
-	done)
-		status_led_on
-		led_off "power1"
-		;;
-	esac
-}
diff --git a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
deleted file mode 100644
index 5664c13..0000000
--- a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ /dev/null
@@ -1,49 +0,0 @@
-#!/bin/sh
-# based on gabors ralink wisoc implementation
-
-rt2x00_eeprom_die() {
-	echo "rt2x00 eeprom: " "$*"
-	exit 1
-}
-
-rt2x00_eeprom_extract() {
-	local part=$1
-	local offset=$2
-	local count=$3
-	local swab=$4
-	local mtd
-
-	. /lib/functions.sh
-
-	mtd=$(find_mtd_part $part)
-	[ -n "$mtd" ] || \
-		rt2x00_eeprom_die "no mtd device found for partition $part"
-
-	if [ $swab -gt 0 ]; then
-		dd if=$mtd of=/lib/firmware/$FIRMWARE bs=2 skip=$offset count=$count conv=swab || \
-			rt2x00_eeprom_die "failed to extract from $mtd"
-	else
-		dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count || \
-			rt2x00_eeprom_die "failed to extract from $mtd"
-	fi
-}
-
-[ -e /lib/firmware/$FIRMWARE ] && exit 0
-. /lib/functions/lantiq.sh
-
-case "$FIRMWARE" in
-"RT2860.eeprom" )
-	local board=$(lantiq_board_name)
-	case $board in
-	ARV7510PW22|ARV7519PW|ARV752DPW|ARV752DPW22)
-		rt2x00_eeprom_extract "board_config" 520 256 1
-		;;
-	ARV7525PW)
-		rt2x00_eeprom_extract "board_config" 1040 512 0
-		;;
-	*)
-		rt2x00_eeprom_die "board $board is not supported yet"
-		;;
-	esac
-	;;
-esac
diff --git a/target/linux/lantiq/base-files/etc/init.d/dsl_fs b/target/linux/lantiq/base-files/etc/init.d/dsl_fs
deleted file mode 100755
index 09c8a4a..0000000
--- a/target/linux/lantiq/base-files/etc/init.d/dsl_fs
+++ /dev/null
@@ -1,35 +0,0 @@
-#!/bin/sh /etc/rc.common
-# Copyright (C) 2014 OpenWrt.org
-
-. /lib/functions.sh
-
-START=30
-
-boot() {
-	MTD=$(find_mtd_index dsl_fw)
-
-	grep /lib/firmware/lantiq /proc/mounts && umount /lib/firmware/lantiq
-
-	mkdir -p /lib/firmware/lantiq
-	[ "$MTD" -gt 0 ] || return 0
-
-	mount -t tmpfs none /lib/firmware/lantiq
-	case "$(dd if=/dev/mtd$MTD bs=2 count=1 2>/dev/null | hexdump -n 2 -e '1/1 "%02x"')" in
-		1985)
-			mkdir -p /tmp/fw_mnt
-			mount -t jffs2 /dev/mtdblock$MTD /tmp/fw_mnt
-			cp -a /tmp/fw_mnt/*.bin /lib/firmware/lantiq/
-			umount /tmp/fw_mnt
-			rmdir /tmp/fw_mnt
-		;;
-		1f8b)
-			tar xz -C /lib/firmware/lantiq < /dev/mtd$MTD
-		;;
-		*)
-			echo "No DSL firmware detected in /dev/mtd$MTD (dsl_fw)"
-			return 0
-		;;
-	esac
-
-	[ -e /lib/firmware/vdsl.bin ] || ln -s /lib/firmware/lantiq/vr9_dsl_fw_annex_b.bin /lib/firmware/vdsl.bin
-}
diff --git a/target/linux/lantiq/base-files/etc/init.d/esi b/target/linux/lantiq/base-files/etc/init.d/esi
deleted file mode 100755
index 5635b53..0000000
--- a/target/linux/lantiq/base-files/etc/init.d/esi
+++ /dev/null
@@ -1,7 +0,0 @@
-#!/bin/sh /etc/rc.common
-# Copyright (C) 2013 OpenWrt.org
-
-START=19
-start() {
-	esi $(printf '%X' $((1+0x$(tr -d : </sys/class/net/eth0/address)))) 2>/dev/null || :
-}
diff --git a/target/linux/lantiq/base-files/etc/inittab b/target/linux/lantiq/base-files/etc/inittab
deleted file mode 100644
index 46a1312..0000000
--- a/target/linux/lantiq/base-files/etc/inittab
+++ /dev/null
@@ -1,3 +0,0 @@
-::sysinit:/etc/init.d/rcS S boot
-::shutdown:/etc/init.d/rcS K stop
-ttyLTQ0::askfirst:/bin/ash --login
diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/01_leds b/target/linux/lantiq/base-files/etc/uci-defaults/01_leds
deleted file mode 100644
index 2b3293b..0000000
--- a/target/linux/lantiq/base-files/etc/uci-defaults/01_leds
+++ /dev/null
@@ -1,39 +0,0 @@
-#!/bin/sh
-#
-# Copyright (C) 2011 OpenWrt.org
-# based on ar71xx
-#
-
-. /lib/functions/uci-defaults.sh
-. /lib/functions/lantiq.sh
-
-[ -e "/sys/class/leds/wifi" ] && ucidef_set_led_wlan "wifi" "wifi" "wifi" "phy0tpt"
-[ -e "/sys/class/leds/usb" ] && ucidef_set_led_usbdev "usb" "usb" "usb" "1-1"
-[ -e "/sys/class/leds/usb2" ] && ucidef_set_led_usbdev "usb2" "usb2" "usb2" "2-1"
-[ -e "/sys/class/leds/internet" ] && ucidef_set_led_netdev "internet" "internet" "internet" "pppoe-wan"
-
-for a in `ls /sys/class/leds/`; do
-	grep -q "\[none\]" /sys/class/leds/$a/trigger
-	[ $? -eq 0 ] && ucidef_set_led_default $a $a $a `cat /sys/class/leds/$a/brightness`
-done
-
-board=$(lantiq_board_name)
-
-case "$board" in
-VG3503J)
-	ucidef_set_led_netdev "vdsl" "vdsl" "bt:green:dsl" "ptm0"
-	;;
-BTHOMEHUBV2B)
-	ucidef_set_led_default "power" "power" "soc:blue:power" "1"
-#	ucidef_set_led_wlan "wifi" "wifi" "soc:blue:wireless" "phy0radio"
-	ucidef_set_led_wlan "wifi" "wifi" "soc:blue:wireless" "phy0tpt"
-	ucidef_set_led_netdev "internet" "internet" "soc:blue:broadband" "nas0"
-	ucidef_set_led_usbdev "usb" "usb" "soc:blue:phone" "1-1"
-	;;
-*)
-	;;
-esac
-
-ucidef_commit_leds
-
-exit 0
diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/02_network b/target/linux/lantiq/base-files/etc/uci-defaults/02_network
deleted file mode 100644
index 2dee0c1..0000000
--- a/target/linux/lantiq/base-files/etc/uci-defaults/02_network
+++ /dev/null
@@ -1,183 +0,0 @@
-#!/bin/sh
-#
-# Copyright (C) 2011-2012 OpenWrt.org
-#
-
-[ -e /etc/config/network ] && exit 0
-
-set_atm_wan() {
-	local vpi=$1
-	local vci=$2
-	local encaps=$3
-	local payload=$4
-	uci batch <<EOF
-set network.atm='atm-bridge'
-set network.atm.vpi='$vpi'
-set network.atm.vci='$vci'
-set network.atm.encaps='$encaps'
-set network.atm.payload='$payload'
-set network.wan='interface'
-set network.wan.ifname='nas0'
-set network.wan.proto='pppoe'
-set network.wan.username='foo'
-set network.wan.password='bar'
-set network.wan.ipv6='1'
-set network.wan6='interface'
-set network.wan6.ifname='@wan'
-set network.wan6.proto='dhcpv6'
-EOF
-}
-
-set_adsl_modem() {
-	local annex=$1
-	local firmware=$2
-	uci batch <<EOF
-set network.dsl='adsl'
-set network.dsl.annex='$annex'
-set network.dsl.firmware='$firmware'
-EOF
-}
-
-set_vdsl_modem() {
-	local annex=$1
-	local firmware=$2
-	local tone=$3
-	local xfer_mode=$4
-	uci batch <<EOF
-set network.dsl='vdsl'
-set network.dsl.annex='$annex'
-set network.dsl.firmware='$firmware'
-set network.dsl.tone='$tone'
-set network.dsl.xfer_mode='$xfer_mode'
-EOF
-}
-
-. /lib/functions/uci-defaults.sh
-. /lib/functions/lantiq.sh
-
-touch /etc/config/network
-
-ucidef_set_interface_loopback
-ucidef_set_interface_lan 'eth0'
-
-vpi=1
-vci=32
-annex="a"
-encaps="llc"
-payload="bridged"
-lan_mac=""
-wan_mac=""
-
-board=$(lantiq_board_name)
-
-case "$board" in
-# adm6996
-ARV4510PW)
-	lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
-	wan_mac=$(macaddr_add "$lan_mac" 1)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "3 2 1 0 5t"
-	;;
-
-ARV4520PW)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "3 2 1 0 5t"
-	;;
-
-ACMP252|GIGASX76X)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "4 3 2 1 5t"
-	;;
-
-# ar8316
-ARV4519PW|ARV7510PW22|ARV7518PW|ARV752DPW22)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "0t 2 3 4 5"
-	;;
-
-# rtl8306g
-ARV7519PW)
-	lan_mac=$(mtd_get_mac_binary board_config 22)
-	wan_mac=$(macaddr_add "$lan_mac" 1)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 4t"
-	;;
-
-WBMR)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "0t 2 3 4 5"
-	;;
-
-VG3503J)
-	ucidef_set_interface_lan 'eth0'
-	uci set network.lan.type='none'
-	;;
-
-DGN3500*)
-	lan_mac=$(mtd_get_mac_ascii uboot-env ethaddr)
-	wan_mac=$(macaddr_add "$lan_mac" 1)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "3 2 1 0 5t"
-	;;
-
-GR7000)
-	ucidef_set_interface_wan "eth0"
-	uci set network.lan.ifname=''
-	;;
-
-H201L)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 4t"
-	;;
-
-#rtl8306g
-P2601HNFX)
-	ucidef_set_interface_lan "eth0.1"
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 5t"
-	;;
-
-P2812HNUFX)
-	ucidef_set_interface_lan 'eth0.1'
-	ucidef_add_switch "switch0" "1" "1"
-	ucidef_add_switch_vlan "switch0" "1" "0 1 2 4 5 6t"
-	;;
-
-TDW8970)
-	lan_mac=$(mtd_get_mac_binary boardconfig 61696)
-	wan_mac=$(macaddr_add "$lan_mac" 1)
-	;;
-
-ARV7519RW22)
-	lan_mac=$(mtd_get_mac_binary boardconfig 22)
-	wan_mac=$(macaddr_add "$lan_mac" 1)
-	;;
-
-BTHOMEHUBV2B)
-	lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
-	wan_mac=$(macaddr_add "$lan_mac" 1)
-	;;
-esac
-
-[ -z "$(ls /lib/modules/`uname -r`/ltq_atm*)" ] || set_atm_wan "$vpi" "$vci" "$encaps" "$payload"
-
-if [ -n "$(grep "system type.*: VR9" /proc/cpuinfo)" ]; then
-	set_vdsl_modem "$annex" "/lib/firmware/vdsl.bin" "av" "ptm"
-else
-	set_adsl_modem "$annex" "/lib/firmware/adsl.bin"
-fi
-
-[ -n "$lan_mac" ] && ucidef_set_interface_macaddr lan $lan_mac
-[ -n "$wan_mac" ] && ucidef_set_interface_macaddr wan $wan_mac
-
-uci commit network
-
-exit 0
diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/03_wireless-wps b/target/linux/lantiq/base-files/etc/uci-defaults/03_wireless-wps
deleted file mode 100644
index e75fb84..0000000
--- a/target/linux/lantiq/base-files/etc/uci-defaults/03_wireless-wps
+++ /dev/null
@@ -1,16 +0,0 @@
-. /lib/functions.sh
-. /lib/functions/lantiq.sh
-
-set_wps() {
-	uci set wireless.$1.wps_pushbutton=0
-	uci set wireless.$1.wps_device_name="OpenWrt - $(lantiq_board_model)"
-}
-
-board=$(lantiq_board_name)
-case $board in
-WBMR)
-	config_load wireless
-	config_foreach set_wps wifi-iface
-	uci commit wireless
-	;;
-esac