ramips: add preliminary support for 2.6.32

SVN-Revision: 19343

7 files changed, 316 insertions, 0 deletions

diff --git a/target/linux/ramips/patches-2.6.32/001-mips-add-cp0-compare-irq-function.patch b/target/linux/ramips/patches-2.6.32/001-mips-add-cp0-compare-irq-function.patch
new file mode 100644
index 0000000..babe906
--- /dev/null
+++ b/target/linux/ramips/patches-2.6.32/001-mips-add-cp0-compare-irq-function.patch
@@ -0,0 +1,29 @@
+--- a/arch/mips/kernel/traps.c
++++ b/arch/mips/kernel/traps.c
+@@ -48,6 +48,7 @@
+ #include <asm/types.h>
+ #include <asm/stacktrace.h>
+ #include <asm/irq.h>
++#include <asm/time.h>
+ 
+ extern void check_wait(void);
+ extern asmlinkage void r4k_wait(void);
+@@ -1537,6 +1538,8 @@ void __cpuinit per_cpu_trap_init(void)
+ 	 */
+ 	if (cpu_has_mips_r2) {
+ 		cp0_compare_irq = (read_c0_intctl() >> 29) & 7;
++		if (get_c0_compare_irq)
++			cp0_compare_irq = get_c0_compare_irq();
+ 		cp0_perfcount_irq = (read_c0_intctl() >> 26) & 7;
+ 		if (cp0_perfcount_irq == cp0_compare_irq)
+ 			cp0_perfcount_irq = -1;
+--- a/arch/mips/include/asm/time.h
++++ b/arch/mips/include/asm/time.h
+@@ -52,6 +52,7 @@ extern int (*perf_irq)(void);
+  */
+ #ifdef CONFIG_CEVT_R4K_LIB
+ extern unsigned int __weak get_c0_compare_int(void);
++extern unsigned int __weak get_c0_compare_irq(void);
+ extern int r4k_clockevent_init(void);
+ #endif
+ 
diff --git a/target/linux/ramips/patches-2.6.32/002-mips-clocksource-init-war.patch b/target/linux/ramips/patches-2.6.32/002-mips-clocksource-init-war.patch
new file mode 100644
index 0000000..894eed1
--- /dev/null
+++ b/target/linux/ramips/patches-2.6.32/002-mips-clocksource-init-war.patch
@@ -0,0 +1,56 @@
+--- a/arch/mips/kernel/cevt-r4k.c
++++ b/arch/mips/kernel/cevt-r4k.c
+@@ -16,6 +16,22 @@
+ #include <asm/cevt-r4k.h>
+ 
+ /*
++ * Compare interrupt can be routed and latched outside the core,
++ * so a single execution hazard barrier may not be enough to give
++ * it time to clear as seen in the Cause register.  4 time the
++ * pipeline depth seems reasonably conservative, and empirically
++ * works better in configurations with high CPU/bus clock ratios.
++ */
++
++#define compare_change_hazard() \
++	do { \
++		irq_disable_hazard(); \
++		irq_disable_hazard(); \
++		irq_disable_hazard(); \
++		irq_disable_hazard(); \
++	} while (0)
++
++/*
+  * The SMTC Kernel for the 34K, 1004K, et. al. replaces several
+  * of these routines with SMTC-specific variants.
+  */
+@@ -31,6 +47,7 @@ static int mips_next_event(unsigned long
+ 	cnt = read_c0_count();
+ 	cnt += delta;
+ 	write_c0_compare(cnt);
++	compare_change_hazard();
+ 	res = ((int)(read_c0_count() - cnt) > 0) ? -ETIME : 0;
+ 	return res;
+ }
+@@ -100,22 +117,6 @@ static int c0_compare_int_pending(void)
+ 	return (read_c0_cause() >> cp0_compare_irq) & 0x100;
+ }
+ 
+-/*
+- * Compare interrupt can be routed and latched outside the core,
+- * so a single execution hazard barrier may not be enough to give
+- * it time to clear as seen in the Cause register.  4 time the
+- * pipeline depth seems reasonably conservative, and empirically
+- * works better in configurations with high CPU/bus clock ratios.
+- */
+-
+-#define compare_change_hazard() \
+-	do { \
+-		irq_disable_hazard(); \
+-		irq_disable_hazard(); \
+-		irq_disable_hazard(); \
+-		irq_disable_hazard(); \
+-	} while (0)
+-
+ int c0_compare_int_usable(void)
+ {
+ 	unsigned int delta;
diff --git a/target/linux/ramips/patches-2.6.32/010-mtd_fix_cfi_cmdset_0002_erase_status_check.patch b/target/linux/ramips/patches-2.6.32/010-mtd_fix_cfi_cmdset_0002_erase_status_check.patch
new file mode 100644
index 0000000..22aefe0
--- /dev/null
+++ b/target/linux/ramips/patches-2.6.32/010-mtd_fix_cfi_cmdset_0002_erase_status_check.patch
@@ -0,0 +1,20 @@
+--- a/drivers/mtd/chips/cfi_cmdset_0002.c
++++ b/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -1568,7 +1568,7 @@ static int __xipram do_erase_chip(struct
+ 			chip->erase_suspended = 0;
+ 		}
+ 
+-		if (chip_ready(map, adr))
++		if (chip_good(map, adr, map_word_ff(map)))
+ 			break;
+ 
+ 		if (time_after(jiffies, timeo)) {
+@@ -1656,7 +1656,7 @@ static int __xipram do_erase_oneblock(st
+ 			chip->erase_suspended = 0;
+ 		}
+ 
+-		if (chip_ready(map, adr)) {
++		if (chip_good(map, adr, map_word_ff(map))) {
+ 			xip_enable(map, chip, adr);
+ 			break;
+ 		}
diff --git a/target/linux/ramips/patches-2.6.32/100-mips-ralink-core.patch b/target/linux/ramips/patches-2.6.32/100-mips-ralink-core.patch
new file mode 100644
index 0000000..5bf5f34
--- /dev/null
+++ b/target/linux/ramips/patches-2.6.32/100-mips-ralink-core.patch
@@ -0,0 +1,58 @@
+--- a/arch/mips/Makefile
++++ b/arch/mips/Makefile
+@@ -624,6 +624,26 @@ else
+ load-$(CONFIG_CPU_CAVIUM_OCTEON) 	+= 0xffffffff81100000
+ endif
+ 
++#
++# Ralink SoC common stuff
++#
++core-$(CONFIG_MIPS_RALINK)	+= arch/mips/ralink/common/
++cflags-$(CONFIG_MIPS_RALINK)	+= -I$(srctree)/arch/mips/include/asm/mach-ralink
++
++#
++# Ralink RT288x
++#
++core-$(CONFIG_RALINK_RT288X)	+= arch/mips/ralink/rt288x/
++cflags-$(CONFIG_RALINK_RT288X)	+= -I$(srctree)//arch/mips/include/asm/mach-ralink/rt288x
++load-$(CONFIG_RALINK_RT288X)	+= 0xffffffff88000000
++
++#
++# Ralink RT305x
++#
++core-$(CONFIG_RALINK_RT305X)	+= arch/mips/ralink/rt305x/
++cflags-$(CONFIG_RALINK_RT305X)	+= -I$(srctree)/arch/mips/include/asm/mach-ralink/rt305x
++load-$(CONFIG_RALINK_RT305X)	+= 0xffffffff80000000
++
+ # temporary until string.h is fixed
+ cflags-y += -ffreestanding
+ 
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -43,6 +43,9 @@ config AR7
+ 	  Support for the Texas Instruments AR7 System-on-a-Chip
+ 	  family: TNETD7100, 7200 and 7300.
+ 
++config MIPS_RALINK
++	bool "Ralink MIPS SoC based boards"
++
+ config BASLER_EXCITE
+ 	bool "Basler eXcite smart camera"
+ 	select CEVT_R4K
+@@ -679,6 +682,7 @@ source "arch/mips/bcm63xx/Kconfig"
+ source "arch/mips/jazz/Kconfig"
+ source "arch/mips/lasat/Kconfig"
+ source "arch/mips/pmc-sierra/Kconfig"
++source "arch/mips/ralink/Kconfig"
+ source "arch/mips/sgi-ip27/Kconfig"
+ source "arch/mips/sibyte/Kconfig"
+ source "arch/mips/txx9/Kconfig"
+@@ -1045,7 +1049,7 @@ config BOOT_ELF32
+ 
+ config MIPS_L1_CACHE_SHIFT
+ 	int
+-	default "4" if MACH_DECSTATION || MIKROTIK_RB532 || PMC_MSP4200_EVAL
++	default "4" if MACH_DECSTATION || MIKROTIK_RB532 || PMC_MSP4200_EVAL || RALINK_RT288X
+ 	default "6" if MIPS_CPU_SCACHE
+ 	default "7" if SGI_IP22 || SGI_IP27 || SGI_IP28 || SNI_RM || CPU_CAVIUM_OCTEON
+ 	default "5"
diff --git a/target/linux/ramips/patches-2.6.32/101-rt288x_serial_driver_hack.patch b/target/linux/ramips/patches-2.6.32/101-rt288x_serial_driver_hack.patch
new file mode 100644
index 0000000..06d921f
--- /dev/null
+++ b/target/linux/ramips/patches-2.6.32/101-rt288x_serial_driver_hack.patch
@@ -0,0 +1,118 @@
+--- a/drivers/serial/8250.c
++++ b/drivers/serial/8250.c
+@@ -298,9 +298,9 @@ static const struct serial8250_config ua
+ 	},
+ };
+ 
+-#if defined (CONFIG_SERIAL_8250_AU1X00)
++#if defined (CONFIG_SERIAL_8250_AU1X00) || defined (CONFIG_SERIAL_8250_RT288X)
+ 
+-/* Au1x00 UART hardware has a weird register layout */
++/* Au1x00 and RT288x UART hardware has a weird register layout */
+ static const u8 au_io_in_map[] = {
+ 	[UART_RX]  = 0,
+ 	[UART_IER] = 2,
+@@ -418,7 +418,7 @@ static unsigned int mem32_serial_in(stru
+ 	return readl(p->membase + offset);
+ }
+ 
+-#ifdef CONFIG_SERIAL_8250_AU1X00
++#if defined(CONFIG_SERIAL_8250_AU1X00) || defined(CONFIG_SERIAL_8250_RT288X)
+ static unsigned int au_serial_in(struct uart_port *p, int offset)
+ {
+ 	offset = map_8250_in_reg(p, offset) << p->regshift;
+@@ -499,7 +499,7 @@ static void set_io_from_upio(struct uart
+ 		p->serial_out = mem32_serial_out;
+ 		break;
+ 
+-#ifdef CONFIG_SERIAL_8250_AU1X00
++#if defined (CONFIG_SERIAL_8250_AU1X00) || defined (CONFIG_SERIAL_8250_RT288X)
+ 	case UPIO_AU:
+ 		p->serial_in = au_serial_in;
+ 		p->serial_out = au_serial_out;
+@@ -531,7 +531,7 @@ serial_out_sync(struct uart_8250_port *u
+ 	switch (p->iotype) {
+ 	case UPIO_MEM:
+ 	case UPIO_MEM32:
+-#ifdef CONFIG_SERIAL_8250_AU1X00
++#if defined (CONFIG_SERIAL_8250_AU1X00) || defined (CONFIG_SERIAL_8250_RT288X)
+ 	case UPIO_AU:
+ #endif
+ 	case UPIO_DWAPB:
+@@ -569,8 +569,8 @@ static inline void _serial_dl_write(stru
+ 	serial_outp(up, UART_DLM, value >> 8 & 0xff);
+ }
+ 
+-#if defined(CONFIG_SERIAL_8250_AU1X00)
+-/* Au1x00 haven't got a standard divisor latch */
++#if defined (CONFIG_SERIAL_8250_AU1X00) || defined (CONFIG_SERIAL_8250_RT288X)
++/* Au1x00 and RT288x haven't got a standard divisor latch */
+ static int serial_dl_read(struct uart_8250_port *up)
+ {
+ 	if (up->port.iotype == UPIO_AU)
+@@ -777,22 +777,19 @@ static int size_fifo(struct uart_8250_po
+  */
+ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
+ {
+-	unsigned char old_dll, old_dlm, old_lcr;
++	unsigned char old_lcr;
++	unsigned int old_dl;
+ 	unsigned int id;
+ 
+ 	old_lcr = serial_inp(p, UART_LCR);
+ 	serial_outp(p, UART_LCR, UART_LCR_DLAB);
+ 
+-	old_dll = serial_inp(p, UART_DLL);
+-	old_dlm = serial_inp(p, UART_DLM);
++	old_dl = serial_dl_read(p);
+ 
+-	serial_outp(p, UART_DLL, 0);
+-	serial_outp(p, UART_DLM, 0);
++	serial_dl_write(p, 0);
++	id = serial_dl_read(p);
+ 
+-	id = serial_inp(p, UART_DLL) | serial_inp(p, UART_DLM) << 8;
+-
+-	serial_outp(p, UART_DLL, old_dll);
+-	serial_outp(p, UART_DLM, old_dlm);
++	serial_dl_write(p, old_dl);
+ 	serial_outp(p, UART_LCR, old_lcr);
+ 
+ 	return id;
+@@ -1214,7 +1211,7 @@ static void autoconfig(struct uart_8250_
+ 	}
+ #endif
+ 
+-#ifdef CONFIG_SERIAL_8250_AU1X00
++#if defined (CONFIG_SERIAL_8250_AU1X00) || defined (CONFIG_SERIAL_8250_RT288X)
+ 	/* if access method is AU, it is a 16550 with a quirk */
+ 	if (up->port.type == PORT_16550A && up->port.iotype == UPIO_AU)
+ 		up->bugs |= UART_BUG_NOMSR;
+--- a/drivers/serial/Kconfig
++++ b/drivers/serial/Kconfig
+@@ -266,6 +266,14 @@ config SERIAL_8250_AU1X00
+ 	  say Y to this option. The driver can handle up to 4 serial ports,
+ 	  depending on the SOC. If unsure, say N.
+ 
++config SERIAL_8250_RT288X
++	bool "Ralink RT288x/RT305x serial port support"
++	depends on SERIAL_8250 != n && (SOC_RT288X || SOC_RT305X)
++	help
++	  If you have a Ralink RT288x/RT305x SoC based board and want to use the 
++	  serial port, say Y to this option. The driver can handle up to 2 serial 
++	  ports. If unsure, say N.
++
+ config SERIAL_8250_RM9K
+ 	bool "Support for MIPS RM9xxx integrated serial port"
+ 	depends on SERIAL_8250 != n && SERIAL_RM9000
+--- a/include/linux/serial_core.h
++++ b/include/linux/serial_core.h
+@@ -281,7 +281,7 @@ struct uart_port {
+ #define UPIO_HUB6		(1)
+ #define UPIO_MEM		(2)
+ #define UPIO_MEM32		(3)
+-#define UPIO_AU			(4)			/* Au1x00 type IO */
++#define UPIO_AU			(4)			/* Au1x00 and RT288x type IO */
+ #define UPIO_TSI		(5)			/* Tsi108/109 type IO */
+ #define UPIO_DWAPB		(6)			/* DesignWare APB UART */
+ #define UPIO_RM9000		(7)			/* RM9000 type IO */
diff --git a/target/linux/ramips/patches-2.6.32/102-rt288x-pci-driver-hook.patch b/target/linux/ramips/patches-2.6.32/102-rt288x-pci-driver-hook.patch
new file mode 100644
index 0000000..d2056c6
--- /dev/null
+++ b/target/linux/ramips/patches-2.6.32/102-rt288x-pci-driver-hook.patch
@@ -0,0 +1,10 @@
+--- a/arch/mips/pci/Makefile
++++ b/arch/mips/pci/Makefile
+@@ -55,6 +55,7 @@ obj-$(CONFIG_ZAO_CAPCELLA)	+= fixup-capc
+ obj-$(CONFIG_WR_PPMC)		+= fixup-wrppmc.o
+ obj-$(CONFIG_MIKROTIK_RB532)	+= pci-rc32434.o ops-rc32434.o fixup-rc32434.o
+ obj-$(CONFIG_CPU_CAVIUM_OCTEON)	+= pci-octeon.o pcie-octeon.o
++obj-$(CONFIG_SOC_RT288X)	+= pci-rt288x.o
+ 
+ ifdef CONFIG_PCI_MSI
+ obj-$(CONFIG_CPU_CAVIUM_OCTEON)	+= msi-octeon.o
diff --git a/target/linux/ramips/patches-2.6.32/103-ethernet.patch b/target/linux/ramips/patches-2.6.32/103-ethernet.patch
new file mode 100644
index 0000000..8b370b6
--- /dev/null
+++ b/target/linux/ramips/patches-2.6.32/103-ethernet.patch
@@ -0,0 +1,25 @@
+--- a/drivers/net/Kconfig
++++ b/drivers/net/Kconfig
+@@ -602,6 +602,12 @@ config MIPS_AU1X00_ENET
+ 	  If you have an Alchemy Semi AU1X00 based system
+ 	  say Y.  Otherwise, say N.
+ 
++config MIPS_RAMIPS_NET
++	tristate "Ethernet driver for rt288x/rt305x"
++	depends on MIPS_RALINK
++	help
++	  This driver supports the etehrnet mac inside the ralink wisocs
++
+ config SGI_IOC3_ETH
+ 	bool "SGI IOC3 Ethernet"
+ 	depends on PCI && SGI_IP27
+--- a/drivers/net/Makefile
++++ b/drivers/net/Makefile
+@@ -217,6 +217,7 @@ obj-$(CONFIG_KORINA) += korina.o
+ obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
+ obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
+ obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
++obj-$(CONFIG_MIPS_RAMIPS_NET) += ramips.o
+ obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
+ obj-$(CONFIG_DECLANCE) += declance.o
+ obj-$(CONFIG_ATARILANCE) += atarilance.o