diff options
Diffstat (limited to 'package/boot/uboot-layerscape/patches/0045-board-freescale-ls1012afrdm-Add-support-of-Ethernet.patch')
-rw-r--r-- | package/boot/uboot-layerscape/patches/0045-board-freescale-ls1012afrdm-Add-support-of-Ethernet.patch | 155 |
1 files changed, 0 insertions, 155 deletions
diff --git a/package/boot/uboot-layerscape/patches/0045-board-freescale-ls1012afrdm-Add-support-of-Ethernet.patch b/package/boot/uboot-layerscape/patches/0045-board-freescale-ls1012afrdm-Add-support-of-Ethernet.patch deleted file mode 100644 index 0b993cb..0000000 --- a/package/boot/uboot-layerscape/patches/0045-board-freescale-ls1012afrdm-Add-support-of-Ethernet.patch +++ /dev/null @@ -1,155 +0,0 @@ -From 691deae097b2583a4e9890307c684ce9f58aca78 Mon Sep 17 00:00:00 2001 -From: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> -Date: Tue, 24 May 2016 15:03:33 +0530 -Subject: [PATCH 45/93] board/freescale/ls1012afrdm: Add support of Ethernet - -Add support of SGMII Ethernet present on FRDM board. -Also add support of PHY reset. - -Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> ---- - board/freescale/ls1012afrdm/Makefile | 1 + - board/freescale/ls1012afrdm/eth.c | 86 +++++++++++++++++++++++++++++ - board/freescale/ls1012afrdm/ls1012afrdm.c | 5 -- - include/configs/ls1012afrdm.h | 5 ++ - 4 files changed, 92 insertions(+), 5 deletions(-) - create mode 100644 board/freescale/ls1012afrdm/eth.c - -diff --git a/board/freescale/ls1012afrdm/Makefile b/board/freescale/ls1012afrdm/Makefile -index dbfa2ce..1364f22 100644 ---- a/board/freescale/ls1012afrdm/Makefile -+++ b/board/freescale/ls1012afrdm/Makefile -@@ -5,3 +5,4 @@ - # - - obj-y += ls1012afrdm.o -+obj-y += eth.o -diff --git a/board/freescale/ls1012afrdm/eth.c b/board/freescale/ls1012afrdm/eth.c -new file mode 100644 -index 0000000..8ae3f45 ---- /dev/null -+++ b/board/freescale/ls1012afrdm/eth.c -@@ -0,0 +1,86 @@ -+/* -+ * Copyright 2016 Freescale Semiconductor, Inc. -+ * -+ * SPDX-License-Identifier: GPL-2.0+ -+ */ -+ -+#include <common.h> -+#include <asm/io.h> -+#include <netdev.h> -+#include <fm_eth.h> -+#include <fsl_mdio.h> -+#include <malloc.h> -+#include <fsl_dtsec.h> -+#include <asm/arch/soc.h> -+#include <asm/arch-fsl-layerscape/config.h> -+#include <asm/arch/fsl_serdes.h> -+ -+#include "../../../drivers/net/pfe_eth/pfe_eth.h" -+#include <asm/arch-fsl-layerscape/immap_lsch2.h> -+ -+#define DEFAULT_PFE_MDIO_NAME "PFE_MDIO" -+ -+#define MASK_ETH_PHY_RST 0x00000100 -+ -+void reset_phy(void) -+{ -+ unsigned int val; -+ ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_GPIO1_ADDR); -+ -+ setbits_be32(&pgpio->gpdir, MASK_ETH_PHY_RST); -+ -+ val = in_be32(&pgpio->gpdat); -+ setbits_be32(&pgpio->gpdat, val & ~MASK_ETH_PHY_RST); -+ mdelay(10); -+ -+ val = in_be32(&pgpio->gpdat); -+ setbits_be32(&pgpio->gpdat, val | MASK_ETH_PHY_RST); -+ mdelay(50); -+} -+ -+int board_eth_init(bd_t *bis) -+{ -+#ifdef CONFIG_FSL_PPFE -+ struct mii_dev *bus; -+ struct mdio_info mac1_mdio_info; -+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; -+ -+ -+ /*TODO Following config should be done for all boards, where is the right place to put this */ -+ out_be32(&scfg->pfeasbcr, in_be32(&scfg->pfeasbcr) | SCFG_PPFEASBCR_AWCACHE0); -+ out_be32(&scfg->pfebsbcr, in_be32(&scfg->pfebsbcr) | SCFG_PPFEASBCR_AWCACHE0); -+ -+ /*CCI-400 QoS settings for PFE */ -+ out_be32(&scfg->wr_qos1, 0x0ff00000); -+ out_be32(&scfg->rd_qos1, 0x0ff00000); -+ -+ /* Set RGMII into 1G + Full duplex mode */ -+ out_be32(&scfg->rgmiipcr, in_be32(&scfg->rgmiipcr) | (SCFG_RGMIIPCR_SETSP_1000M | SCFG_RGMIIPCR_SETFD)); -+ -+ -+ out_be32((CONFIG_SYS_DCSR_DCFG_ADDR + 0x520), 0xFFFFFFFF); -+ out_be32((CONFIG_SYS_DCSR_DCFG_ADDR + 0x524), 0xFFFFFFFF); -+ -+ mac1_mdio_info.reg_base = (void *)0x04200000; /*EMAC1_BASE_ADDR*/ -+ mac1_mdio_info.name = DEFAULT_PFE_MDIO_NAME; -+ -+ bus = ls1012a_mdio_init(&mac1_mdio_info); -+ if(!bus) -+ { -+ printf("Failed to register mdio \n"); -+ return -1; -+ } -+ -+ /*MAC1 */ -+ ls1012a_set_mdio(0, miiphy_get_dev_by_name(DEFAULT_PFE_MDIO_NAME)); -+ ls1012a_set_phy_address_mode(0, EMAC1_PHY_ADDR, PHY_INTERFACE_MODE_SGMII); -+ -+ /*MAC2 */ -+ ls1012a_set_mdio(1, miiphy_get_dev_by_name(DEFAULT_PFE_MDIO_NAME)); -+ ls1012a_set_phy_address_mode(1, EMAC2_PHY_ADDR, PHY_INTERFACE_MODE_SGMII); -+ -+ -+ cpu_eth_init(bis); -+#endif -+ return pci_eth_init(bis); -+} -diff --git a/board/freescale/ls1012afrdm/ls1012afrdm.c b/board/freescale/ls1012afrdm/ls1012afrdm.c -index 6be8951..6856250 100644 ---- a/board/freescale/ls1012afrdm/ls1012afrdm.c -+++ b/board/freescale/ls1012afrdm/ls1012afrdm.c -@@ -133,11 +133,6 @@ int dram_init(void) - return 0; - } - --int board_eth_init(bd_t *bis) --{ -- return pci_eth_init(bis); --} -- - int board_early_init_f(void) - { - fsl_lsch2_early_init_f(); -diff --git a/include/configs/ls1012afrdm.h b/include/configs/ls1012afrdm.h -index 3231ab7..5e619c1 100644 ---- a/include/configs/ls1012afrdm.h -+++ b/include/configs/ls1012afrdm.h -@@ -18,8 +18,13 @@ - #define CONFIG_SYS_MEMTEST_START 0x80000000 - #define CONFIG_SYS_MEMTEST_END 0x9fffffff - -+#ifdef CONFIG_FSL_PPFE -+#define EMAC1_PHY_ADDR 0x2 -+#define EMAC2_PHY_ADDR 0x1 - #define CONFIG_PHYLIB - #define CONFIG_PHY_REALTEK -+#define CONFIG_RESET_PHY_R -+#endif - /* - * USB - */ --- -1.7.9.5 - |