summaryrefslogtreecommitdiff
path: root/package/boot/uboot-xburst/files/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'package/boot/uboot-xburst/files/include/configs')
-rw-r--r--package/boot/uboot-xburst/files/include/configs/avt2.h26
-rw-r--r--package/boot/uboot-xburst/files/include/configs/n516.h311
-rw-r--r--package/boot/uboot-xburst/files/include/configs/nanonote.h191
-rw-r--r--package/boot/uboot-xburst/files/include/configs/qi_lb60.h27
-rw-r--r--package/boot/uboot-xburst/files/include/configs/sakc.h200
5 files changed, 755 insertions, 0 deletions
diff --git a/package/boot/uboot-xburst/files/include/configs/avt2.h b/package/boot/uboot-xburst/files/include/configs/avt2.h
new file mode 100644
index 0000000..cbf34d7
--- /dev/null
+++ b/package/boot/uboot-xburst/files/include/configs/avt2.h
@@ -0,0 +1,26 @@
+#ifndef __CONFIG_AVT2_H
+#define __CONFIG_AVT2_H
+
+#include <configs/nanonote.h>
+
+#define CONFIG_AVT2 1
+
+#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait avt2=1"
+#define CONFIG_BOOTARGSFROMSD "mem=64M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait avt2=1"
+#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm"
+
+/* SDRAM paramters */
+#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW 13 /* Row address: 11 to 13 */
+#define SDRAM_COL 10 /* Column address: 8 to 12 */
+#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */
+
+/* SDRAM Timings, unit: ns */
+#define SDRAM_TRAS 45 /* RAS# Active Time */
+#define SDRAM_RCD 20 /* RAS# to CAS# Delay */
+#define SDRAM_TPC 20 /* RAS# Precharge Time */
+#define SDRAM_TRWL 7 /* Write Latency Time */
+#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */
+
+#endif /* __CONFIG_AVT_H */
diff --git a/package/boot/uboot-xburst/files/include/configs/n516.h b/package/boot/uboot-xburst/files/include/configs/n516.h
new file mode 100644
index 0000000..c741bfe
--- /dev/null
+++ b/package/boot/uboot-xburst/files/include/configs/n516.h
@@ -0,0 +1,311 @@
+/*
+ * (C) Copyright 2006
+ * Ingenic Semiconductor, <jlwei@ingenic.cn>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * This file contains the configuration parameters for the pavo board.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+//#define DEBUG
+//#define DEBUG_SHELL
+
+#define CONFIG_MIPS32 1 /* MIPS32 CPU core */
+#define CONFIG_JzRISC 1 /* JzRISC core */
+#define CONFIG_JZSOC 1 /* Jz SoC */
+#define CONFIG_JZ4740 1 /* Jz4740 SoC */
+#define CONFIG_PAVO 1 /* PAVO validation board */
+
+#define CONFIG_BOARD_NAME "n516"
+#define CONFIG_BOARD_HWREV "1.0"
+#define CONFIG_FIRMWARE_EPOCH "0"
+#define CONFIG_UPDATE_TMPBUF 0x80600000
+#define CONFIG_UPDATE_CHUNKSIZE 0x800000
+#define CONFIG_UPDATE_FILENAME "update.oifw"
+#define CONFIG_UPDATE_FILEEXT ".oifw"
+#define CONFIG_UBI_PARTITION "UBI"
+
+#define CONFIG_SKIP_LOWLEVEL_INIT 1
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+
+#if 0
+#define CONFIG_LCD /* LCD support */
+#define CONFIG_JZLCD_METRONOME_800x600
+#define LCD_BPP LCD_COLOR8
+
+#define WFM_DATA_SIZE ( 1 << 14 )
+#define CONFIG_METRONOME_WF_LEN (64 * (1 << 10))
+#define CONFIG_METRONOME_WF_NAND_OFFSET (0x100000)
+#define BMP_LOGO_HEIGHT 0
+#define CONFIG_UBI_WF_VOLUME "waveforms"
+#define CONFIG_UBI_BOOTSPLASH_VOLUME "bootsplash"
+#define CONFIG_METRONOME_BOOTSPLASH_LEN 480000
+#endif
+
+#if 0
+#define CONFIG_JZSOC_I2C
+#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 0
+#define CONFIG_LPC_I2C_ADDR 0x54
+#endif
+
+#define JZ4740_NORBOOT_CFG JZ4740_NORBOOT_16BIT /* NOR Boot config code */
+#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 /* NAND Boot config code */
+
+#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */
+#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */
+#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL/256) /* incrementer freq */
+
+#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */
+
+#define CONFIG_BAUDRATE 57600
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+
+#define CONFIG_MMC 1
+#define CONFIG_GENERIC_MMC 1
+#define CONFIG_JZ_MMC 1
+#define CONFIG_FAT 1
+
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 ">"
+#define CONFIG_CMDLINE_EDITING
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_BDI /* bdinfo */
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_ECHO /* echo arguments */
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_ITEST /* Integer (and string) test */
+#undef CONFIG_CMD_LOADB /* loadb */
+#undef CONFIG_CMD_LOADS /* loads */
+#undef CONFIG_CMD_NFS /* NFS support */
+#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
+#undef CONFIG_CMD_SOURCE /* "source" command support */
+#undef CONFIG_CMD_XIMG /* Load part of Multi Image */
+#undef CONFIG_CMD_NET
+
+//#define CONFIG_CMD_ASKENV
+//#define CONFIG_CMD_DHCP
+//#define CONFIG_CMD_PING
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+/*#define CONFIG_CMD_UBI*/
+/*#define CONFIG_CMD_MTDPARTS*/
+//#define CONFIG_CMD_JFFS2
+//#define CONFIG_JFFS2_NAND
+//#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_UPDATE
+
+#define CONFIG_DOS_PARTITION
+
+/*#define CONFIG_MTD_PARTITIONS*/
+#define CONFIG_RBTREE
+
+#define CONFIG_BOOTP_MASK ( CONFIG_BOOTP_DEFAUL )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#if 0
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_BOOTDELAY 0
+#define CONFIG_BOOTFILE uImage /* file to load */
+#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ip=off rootfstype=ubifs root=ubi:rootfs ubi.mtd=UBI rw panic=5 " MTDPARTS_DEFAULT
+#define CONFIG_BOOTCOMMAND "check_and_update; setenv bootargs $bootargs $batt_level_param; ubi read 0x80600000 bootsplash && show_image 0x80600000; ubi read 0x80600000 kernel; bootm 0x80600000; ubi read 0x80600000 errorsplash && show_image 0x80600000; while test 0 = 0; do check_and_update; done"
+#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */
+#define CONFIG_IPADDR 192.168.111.1
+#define CONFIG_SERVERIP 192.168.111.2
+#define MTDIDS_DEFAULT "nand0=jz4740-nand"
+#define MTDPARTS_DEFAULT "mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)"
+#define CONFIG_EXTRA_ENV_SETTINGS "mtdids=nand0=jz4740-nand\0mtdparts=mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)\0" \
+ "stdout=serial\0stderr=lcd\0"
+#endif
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL)
+#define CONFIG_BOOTDELAY 0
+#define CONFIG_BOOTFILE "uImage" /* file to load */
+#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
+#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm"
+
+
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/*
+ * Serial download configuration
+ *
+ */
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "n516 # " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/
+
+#define CONFIG_SYS_MALLOC_LEN 1024*1024*2
+#define CONFIG_SYS_BOOTPARAMS_LEN 128*1024
+
+#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */
+
+#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
+
+#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */
+
+#define CONFIG_SYS_MEMTEST_START 0x80100000
+#define CONFIG_SYS_MEMTEST_END 0x80800000
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#else
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#endif
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH configuration
+ */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xB8000000
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 8k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */
+
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE 63 /* NAND bad block was marked at this page in a block, starting from 0 */
+#define CONFIG_SYS_NAND_ECC_POS 6
+
+#ifdef CONFIG_ENV_IS_IN_NAND
+//#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_SIZE (128 * 1024)
+//#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) /* environment starts here */
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_U_BOOT_OFFS)
+//#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * NOR FLASH and environment organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT (128) /* max number of sectors on one chip */
+
+#define PHYS_FLASH_1 0xa8000000 /* Flash Bank #1 */
+
+/* The following #defines are needed to get flash environment right */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* in pavo/config.mk TEXT_BASE=0x88000000*/
+#define CONFIG_SYS_SYS_MONITOR_BASE TEXT_BASE /* in pavo/config.mk TEXT_BASE=0x88000000*/
+#define CONFIG_SYS_MONITOR_LEN (256*1024) /* Reserve 256 kB for Monitor */
+
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Timeout for Flash Write */
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_IS_NOWHERE 1
+#define CONFIG_ENV_ADDR 0xa8040000
+#define CONFIG_ENV_SIZE 0x20000
+#endif
+
+/*-----------------------------------------------------------------------
+ * SDRAM Info.
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+
+// SDRAM paramters
+#define SDRAM_BW16 0 /* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW 13 /* Row address: 11 to 13 */
+#define SDRAM_COL 9 /* Column address: 8 to 12 */
+#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */
+
+// SDRAM Timings, unit: ns
+#define SDRAM_TRAS 45 /* RAS# Active Time */
+#define SDRAM_RCD 20 /* RAS# to CAS# Delay */
+#define SDRAM_TPC 20 /* RAS# Precharge Time */
+#define SDRAM_TRWL 7 /* Write Latency Time */
+#define SDRAM_TREF 15625 /* Refresh period: 4096 refresh cycles/64ms */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_DCACHE_SIZE 16384
+#define CONFIG_SYS_ICACHE_SIZE 16384
+#define CONFIG_SYS_CACHELINE_SIZE 32
+
+/*-----------------------------------------------------------------------
+ * GPIO definition
+ */
+#define GPIO_SD_VCC_EN_N 113 /* GPD17 */
+#define GPIO_SD_CD_N 103 /* GPD7 */
+#define GPIO_SD_WP 111 /* GPD15 */
+#define GPIO_USB_DETE 115 /* GPD6 */
+//#define GPIO_DC_DETE_N 103 /* GPD7 */
+#define GPIO_CHARG_STAT_N 112 /* GPD15 */
+#define GPIO_DISP_OFF_N 97 /* GPD1 */
+#define GPIO_UDC_HOTPLUG 100 /* GPD4 */
+#define GPIO_LED_EN 124 /* GPD28 */
+
+#define GPIO_RST_L 50 /* GPB18 LCD_SPL */
+#define GPIO_LCDRDY 49 /* GPB17 LCD_CLS */
+#define GPIO_STBY 86 /* GPC22 LCD_PS */
+#define GPIO_ERR 87 /* GPC23 LCD_REV */
+
+#endif /* __CONFIG_H */
diff --git a/package/boot/uboot-xburst/files/include/configs/nanonote.h b/package/boot/uboot-xburst/files/include/configs/nanonote.h
new file mode 100644
index 0000000..8926877
--- /dev/null
+++ b/package/boot/uboot-xburst/files/include/configs/nanonote.h
@@ -0,0 +1,191 @@
+/*
+ * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 3 of the License, or (at your option) any later version.
+ */
+
+/*
+ * This file contains the configuration parameters for the NanoNote.
+ */
+#ifndef __CONFIG_NANONOTE_H
+#define __CONFIG_NANONOTE_H
+
+#define CONFIG_MIPS32 1 /* MIPS32 CPU core */
+#define CONFIG_JzRISC 1 /* JzRISC core */
+#define CONFIG_JZSOC 1 /* Jz SoC */
+#define CONFIG_JZ4740 1 /* Jz4740 SoC */
+#define CONFIG_NANONOTE 1
+
+#define CONFIG_LCD 1 /* LCD support */
+#define LCD_BPP LCD_COLOR32 /*5:18,24,32 bits per pixel */
+#define CONFIG_SYS_WHITE_ON_BLACK 1
+
+#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */
+#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */
+#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */
+#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED
+
+#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */
+#define CONFIG_BAUDRATE 57600
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_MMC 1
+#define CONFIG_FAT 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_SKIP_LOWLEVEL_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
+#define CONFIG_SYS_NO_FLASH 1
+#define CONFIG_ENV_OVERWRITE 1
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL)
+#define CONFIG_BOOTDELAY 0
+#define CONFIG_BOOTFILE "uImage" /* file to load */
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_BOOTD /* bootd */
+#define CONFIG_CMD_CONSOLE /* coninfo */
+#define CONFIG_CMD_ECHO /* echo arguments */
+
+#define CONFIG_CMD_LOADB /* loadb */
+#define CONFIG_CMD_LOADS /* loads */
+#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
+#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/
+#define CONFIG_CMD_RUN /* run command in env variable */
+#define CONFIG_CMD_SAVEENV /* saveenv */
+#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
+#define CONFIG_CMD_SOURCE /* "source" command support */
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+
+/*
+ * Serial download configuration
+ */
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "QI# " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/
+
+#define CONFIG_SYS_MALLOC_LEN 896 * 1024
+#define CONFIG_SYS_BOOTPARAMS_LEN 128 * 1024
+
+#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */
+#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
+#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */
+#define CONFIG_SYS_MEMTEST_START 0x80100000
+#define CONFIG_SYS_MEMTEST_END 0x80800000
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+
+/*
+ * NAND FLASH configuration
+ */
+/* NAND Boot config code */
+#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3
+
+#define NANONOTE_NAND_SIZE 2 /* if board nand flash is 1GB, set to 1
+ * if board nand flash is 2GB, set to 2
+ * for change the PAGE_SIZE and BLOCK_SIZE
+ * will delete when there is no 1GB flash
+ */
+
+#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * NANONOTE_NAND_SIZE)
+/* nand chip block size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * NANONOTE_NAND_SIZE << 10)
+/* nand bad block was marked at this page in a block, start from 0 */
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127
+/* ECC offset position in oob area, default value is 6 if it isn't defined */
+#define CONFIG_SYS_NAND_ECC_POS (6 * NANONOTE_NAND_SIZE)
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xB8000000
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/
+#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 8k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+/* Start NUB from this addr*/
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */
+
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE)
+/* environment starts here */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* in board/nanonote/config.mk TEXT_BAS = 0x88000000 */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+
+/*
+ * SDRAM Info.
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+
+/*
+ * Cache Configuration
+ */
+#define CONFIG_SYS_DCACHE_SIZE 16384
+#define CONFIG_SYS_ICACHE_SIZE 16384
+#define CONFIG_SYS_CACHELINE_SIZE 32
+
+/*
+ * GPIO definition
+ */
+#define GPIO_LCD_CS (2 * 32 + 21)
+#define GPIO_DISP_OFF_N (3 * 32 + 21)
+#define GPIO_PWM (3 * 32 + 27)
+
+#define GPIO_AMP_EN (3 * 32 + 4)
+
+#define GPIO_SDPW_EN (3 * 32 + 2)
+#define GPIO_SD_DETECT (3 * 32 + 0)
+
+#define GPIO_USB_DETECT (3 * 32 + 27)
+#define GPIO_BUZZ_PWM (3 * 32 + 28)
+
+#define GPIO_AUDIO_POP (1 * 32 + 29)
+#define GPIO_COB_TEST (1 * 32 + 30)
+
+#define GPIO_KEYOUT_BASE (2 * 32 + 10)
+#define GPIO_KEYIN_BASE (3 * 32 + 18)
+#define GPIO_KEYIN_8 (3 * 32 + 26)
+
+#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */
+#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */
+
+#endif /* __CONFIG_NANONOTE_H */
diff --git a/package/boot/uboot-xburst/files/include/configs/qi_lb60.h b/package/boot/uboot-xburst/files/include/configs/qi_lb60.h
new file mode 100644
index 0000000..1542c3d
--- /dev/null
+++ b/package/boot/uboot-xburst/files/include/configs/qi_lb60.h
@@ -0,0 +1,27 @@
+#ifndef __CONFIG_QI_LB60_H
+#define __CONFIG_QI_LB60_H
+
+#include <configs/nanonote.h>
+
+#define CONFIG_QI_LB60 1
+
+#define CONFIG_BOOTARGS "mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
+#define CONFIG_BOOTARGSFROMSD "mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p2 rw rootwait"
+#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm"
+#define CONFIG_BOOTCOMMANDFROMSD "mmc init; fatload mmc 0 0x80600000 uImage; bootm"
+
+/* SDRAM paramters */
+#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW 13 /* Row address: 11 to 13 */
+#define SDRAM_COL 9 /* Column address: 8 to 12 */
+#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */
+
+/* SDRAM Timings, unit: ns */
+#define SDRAM_TRAS 45 /* RAS# Active Time */
+#define SDRAM_RCD 20 /* RAS# to CAS# Delay */
+#define SDRAM_TPC 20 /* RAS# Precharge Time */
+#define SDRAM_TRWL 7 /* Write Latency Time */
+#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */
+
+#endif
diff --git a/package/boot/uboot-xburst/files/include/configs/sakc.h b/package/boot/uboot-xburst/files/include/configs/sakc.h
new file mode 100644
index 0000000..b88d8b0
--- /dev/null
+++ b/package/boot/uboot-xburst/files/include/configs/sakc.h
@@ -0,0 +1,200 @@
+/*
+ * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 3 of the License, or (at your option) any later version.
+ */
+
+/*
+ * This file contains the configuration parameters for SAKC.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define DEBUG
+#define CONFIG_MIPS32 1 /* MIPS32 CPU core */
+#define CONFIG_JzRISC 1 /* JzRISC core */
+#define CONFIG_JZSOC 1 /* Jz SoC */
+#define CONFIG_JZ4725 1 /* Jz4725 SoC */
+#define CONFIG_JZ4740 1 /* Jz4740 SoC */
+#define CONFIG_SAKC 1 /* SAKC board */
+
+#define MMC_BUS_WIDTH_1BIT 1 /* 1 for MMC 1Bit Bus Width */
+
+//#define CONFIG_LCD 1 /* LCD support */
+//#define LCD_BPP LCD_COLOR32 /*5:18,24,32 bits per pixel */
+//#define CONFIG_SYS_WHITE_ON_BLACK 1
+
+#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */
+#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */
+#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */
+#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED
+
+#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */
+#define CONFIG_BAUDRATE 57600
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_MMC 1
+#define CONFIG_FAT 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_SKIP_LOWLEVEL_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
+#define CONFIG_SYS_NO_FLASH 1
+#define CONFIG_ENV_OVERWRITE 1
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL)
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTFILE "uImage" /* file to load */
+#define CONFIG_BOOTARGS "mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
+#define CONFIG_EXTRA_ENV_SETTINGS 1
+#define CONFIG_BOOTARGSFROMSD "mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait"
+#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm"
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_BDI /* bdinfo */
+#define CONFIG_CMD_BOOTD /* bootd */
+#define CONFIG_CMD_CONSOLE /* coninfo */
+#define CONFIG_CMD_ECHO /* echo arguments */
+#define CONFIG_CMD_IMI /* iminfo */
+#define CONFIG_CMD_ITEST /* Integer (and string) test */
+
+#define CONFIG_CMD_LOADB /* loadb */
+#define CONFIG_CMD_LOADS /* loads */
+#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
+#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/
+#define CONFIG_CMD_RUN /* run command in env variable */
+#define CONFIG_CMD_SAVEENV /* saveenv */
+#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
+#define CONFIG_CMD_SOURCE /* "source" command support */
+#define CONFIG_CMD_XIMG /* Load part of Multi Image */
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+
+/*
+ * Serial download configuration
+ */
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "SAKC# " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/
+
+#define CONFIG_SYS_MALLOC_LEN 128 * 1024
+#define CONFIG_SYS_BOOTPARAMS_LEN 128 * 1024
+
+#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */
+#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
+#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */
+#define CONFIG_SYS_MEMTEST_START 0x80100000
+#define CONFIG_SYS_MEMTEST_END 0x80800000
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+
+/*
+ * NAND FLASH configuration
+ */
+/* NAND Boot config code */
+#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3
+
+#define SAKC_NAND_SIZE 1 /* if board nand flash is 1GB, set to 1
+ * if board nand flash is 2GB, set to 2
+ * for change the PAGE_SIZE and BLOCK_SIZE
+ * will delete when there is no 1GB flash
+ */
+
+#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * SAKC_NAND_SIZE)
+/* nand chip block size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * SAKC_NAND_SIZE << 10)
+/* nand bad block was marked at this page in a block, start from 0 */
+#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127
+/* ECC offset position in oob area, default value is 6 if it isn't defined */
+#define CONFIG_SYS_NAND_ECC_POS (6 * SAKC_NAND_SIZE)
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xB8000000
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/
+#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 8k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+/* Start NUB from this addr*/
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */
+
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE)
+/* environment starts here */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* in qi_lb60.h/config.mk TEXT_BAS = 0x88000000 */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+
+/*
+ * SDRAM Info.
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+
+/* SDRAM paramters */
+#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */
+#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */
+#define SDRAM_ROW 13 /* Row address: 11 to 13 */
+#define SDRAM_COL 9 /* Column address: 8 to 12 */
+#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */
+
+/* SDRAM Timings, unit: ns */
+#define SDRAM_TRAS 45 /* RAS# Active Time */
+#define SDRAM_RCD 20 /* RAS# to CAS# Delay */
+#define SDRAM_TPC 20 /* RAS# Precharge Time */
+#define SDRAM_TRWL 7 /* Write Latency Time */
+#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */
+
+/*
+ * Cache Configuration
+ */
+#define CONFIG_SYS_DCACHE_SIZE 16384
+#define CONFIG_SYS_ICACHE_SIZE 16384
+#define CONFIG_SYS_CACHELINE_SIZE 32
+
+/*
+ * GPIO definition
+ */
+#define GPIO_SD_DETECT (2 * 32 + 27)
+#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */
+#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */
+
+#endif /* __CONFIG_H */