summaryrefslogtreecommitdiff
path: root/target/linux/ipq806x/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: fix numbering for Netgear R7800 LAN portsAleksandr V. Piskunov2018-07-041-5/+5
| | | | | | | | | | Netgear R7800 switch LAN ports are numbered backwards in LuCI, i.e. numbering is not corresponding to the actual physical port labels, patch fixes that. Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com> [merged with existing board using the same config] Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: switch the NBG6817 wlan LEDs from amber to whiteStefan Lippers-Hollmann2018-06-281-2/+0
| | | | | | | | | | | | | | | | | The original device support patch configured the amber wlan LEDs (which are meant as error indicator by the OEM) controlled by the SOC's GPIO as wlan traffic indicators, as the correct white wlan LEDs are connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were not accessible. The recent addition of GPIO/ LED support to ath10k now makes it possible to use the correct white LEDs instead - and "mac80211: ath10k: use tpt LED trigger by default" also enables them by default. While both LEDs are independent of each other (two separate LEDs sharing one light tunnel), triggering both on wlan traffic is not the intended behaviour (bright yellow light). Tested on the ZyXEL NBG6817. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-195-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for Compex WPQ864Christian Mehlis2018-03-153-10/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop ipq40xx supportJohn Crispin2018-03-145-161/+0
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: add support for GL.iNet GL-B1300Dongming Han2018-02-143-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for GL.iNet GL-B1300 Specification: - SOC: IPQ4028 / QCA Dakota - RAM: 256 MiB - FLASH: 32 MiB - ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN) - USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) - WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2 - WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2 - INPUT: one reset and one WPS button - LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved - UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1 Installation: Method 1: - use serial port to stop uboot - uboot command: run lf Method 2: - push down reset button and power on - wait until three leds constantly on then release - upgrade by uboot web at http://192.168.1.1 Note: - the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method. - the sysupgrade image can be automatically downloaded if tftp server at 192.168.1.2 have that file. - the wifi led will be flashing when writing image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq806x: switch to full dual-boot for the nbg6817 sysupgrade supportStefan Lippers-Hollmann2018-02-131-3/+23
| | | | | | | | | | | | | | Instead of writing to the currently booted partition set, this implements full dual-boot support for sysupgrade by always writing to the other, currently inactive, partition set and toggling the dualflag after a successful flash. The currently active/ booted partition set is determined by parsing /proc/cmdline for its rootfs parameter (supplied by the DTS), instead of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially) bricking both partition sets. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: request the first free loop device dynamically for the nbg6817 ↵Stefan Lippers-Hollmann2018-02-131-4/+5
| | | | | | | | | | | | sysupgrade Instead of hardcoding /dev/loop0, it's safer to query for the first free loop device and assign that dynamically. While /dev/loop0 is a reasonable assumption immediately following "losetup --detach-all", detaching the mounted overlay is no longer strictly necessary once dual-boot support has been added for the nbg6817. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: use absolute the device path in $kernel for the nbg6817 sysupgradeStefan Lippers-Hollmann2018-02-131-4/+4
| | | | | | | Harmonize the variable usage for $kernel and $rootfs to always contain the full device path, instead of just its basename. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: mark AVM FB4040 switchport as untaggedDavid Bauer2018-02-111-1/+1
| | | | | | | | This commit marks the CPUs switchport explicit as untagged. Otherwise, an eth0.1 interface is created and the devices LAN-ports are not working. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: fix ZyXEL NBG6817 sysupgradeMathias Kresin2018-01-181-7/+10
| | | | | | | | | | | Use the first found directory in the tar archive instead of relying on a directory named according to the userspace boardname. It allows to change the boardname without adding another compatibility layer to the zyxel sysupgrade. Fixes: 33f09cf15178 ("ipq806x: convert to dt-based board-detection") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: add support for OpenMesh A42Sven Eckelmann2018-01-134-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ401x * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet * powered only via POE - 802.3af POE on Ethernet 1 - 18-24v passive POE (mode B) on Ethernet 2 The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq806x: Sort occurrences of boardame alphabeticallyLuis Araneda2018-01-135-63/+62
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: convert to dt-based board-detectionLuis Araneda2018-01-139-152/+76
| | | | | | | | | | | | | | | | | Use the generic board detection method: - Board name: First compatible string from the device tree - Board model: Model property from the device tree Change occurrences of board name in userspace by the compatible string, and removed target specific board detection script Replace the definition of SUPPORTED_DEVICES in Device/Default to extract the dt compatible string from each device definition. Additionally, for devices supported by lede-17.01, append the value of BOARD_NAME to SUPPORTED_DEVICES in the device definition. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: add a helper variable with the vendor name strippedLuis Araneda2018-01-131-0/+1
| | | | | | | | | | This will allow to maintain the current syntax for LEDs config when switching to a device tree compatible string boardname. None of the current boards use a comma in the boardname, so they will be unaffected. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* base-files: unify get_dt_led helper functionChristian Lamparter2017-12-142-17/+4
| | | | | | | | | | | | | | Lantiq and IPQ806X (which includes IPQ40XX) both define the same custom function {ipq806x|lantiq}_get_dt_led. This patch moves the function into the base-file package at lib/functions/leds.sh to make it more accessible for other targets as well. Cc: Mathias Kresin <dev@kresin.me> Cc: John Crispin <john@phrozen.org> Cc: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ip806x: nbg6817: sysupgrade support both targets for kernel/ rootfs partitionsStefan Lippers-Hollmann2017-10-291-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With this commit and the previous "nbg6817: don't hardcode the rootfs location by using append-rootblock instead" applied, it is possible to boot- and sysupgrade from both dual-boot sets (the primary mmcblk0p4+mmcblk0p5 or the alternative mmcblk0p7+mmcblk0p8). However the sysupgrade support does not toggle between both dual-boot sets between firmware upgrades so far. The partition map of the eMMC used in the nbg6817 is: Found valid GPT with protective MBR; using GPT. Disk /dev/mmcblk0: 7471104 sectors, 3.6 GiB Logical sector size: 512 bytes Disk identifier (GUID): XXX Partition table holds up to 12 entries First usable sector is 34, last usable sector is 7471070 Partitions will be aligned on 2-sector boundaries Total free space is 1 sectors (512 bytes) Number Start (sector) End (sector) Size Code Name 1 34 8225 4.0 MiB FFFF rootfs_data 2 8226 16417 4.0 MiB FFFF romd 3 16418 18465 1024.0 KiB FFFF header 4 18466 26657 4.0 MiB FFFF kernel 5 26658 157729 64.0 MiB FFFF rootfs 6 157730 159777 1024.0 KiB FFFF header_1 7 159778 167969 4.0 MiB FFFF kernel_1 8 167970 299041 64.0 MiB FFFF rootfs_1 9 299042 823329 256.0 MiB FFFF bu1 10 823330 7471069 3.2 GiB FFFF bu2 rootfs_data is the ext4 formatted overlay of the OEM firmware, LEDE ignores it due to its (too) small size. romd/ bu1 are initialized with zeroes (0x00) and unused. bu2 is formatted with ext4 and used for streamboost and other optional functionality by the OEM firmware, it is reformatted during factory resets of the OEM firmware. header/ header_1 contains version information for the corresponding vendor firmwares installed to kernel/rootfs or kernel_1/ rootfs_1, the format hasn't been completely reverse engineered so far and remains left untouched by LEDE: V1.00(ABCS.2)C0: 00000000 00 00 a7 74 01 32 f0 00 56 31 2e 30 30 28 41 42 |...t.2..V1.00(AB| 00000010 43 53 2e 32 29 43 30 00 ff ff ff ff ff ff ff ff |CS.2)C0.........| 00000020 ff ff ff ff ff ff ff ff 00 00 d5 dc 4e 42 47 36 |............NBG6| 00000030 38 31 37 00 ff ff ff ff ff ff ff ff ff ff ff ff |817.............| 00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00000060 ff ff ff ff ff ff ff ff ff ff ff ff 00 00 22 a3 |..............".| 00000070 00 1c 70 00 ff ff ff ff ff ff ff ff ff ff ff ff |..p.............| 00000080 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00000800 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00100000 V1.00(ABCS.5)C0: 00000000 00 00 bf 94 01 46 d8 00 56 31 2e 30 30 28 41 42 |.....F..V1.00(AB| 00000010 43 53 2e 35 29 43 30 00 ff ff ff ff ff ff ff ff |CS.5)C0.........| 00000020 ff ff ff ff ff ff ff ff 00 00 d6 5a 4e 42 47 36 |...........ZNBG6| 00000030 38 31 37 00 ff ff ff ff ff ff ff ff ff ff ff ff |817.............| 00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00000060 ff ff ff ff ff ff ff ff ff ff ff ff 00 00 c0 2c |...............,| 00000070 00 1c 58 00 ff ff ff ff ff ff ff ff ff ff ff ff |..X.............| 00000080 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00010000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00100000 Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: ipq4019: add ap-dk01.1-c1 board supportRoman Yeryomin2017-10-302-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AP-DK01.1-C1 is QCA dev board with: - ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio - 256MB RAM - 32MB SPI flash - QCA8075 multiport ethernet phy (WAN port, 4x LAN ports) First installation via u-boot: sf probe sf erase 0x180000 0x1a00000 tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin sf write 0x84000000 0x180000 $filesize Further upgrades via sysupgrade. Changes: - add partitions - set memory size to 256MB - add reserved memory mapping - add correct compatible string - add image generation - extract pre-cal data from ART partition Compile and run tested. Wirespeed NAT can be achieved with spreading rx interrupts over different cores. Wifi speed is ~550Mbps @5GHz in open air. Note: AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has ipq4028 instead of ipq4018 on board. Changes since v2: - based on dts(i) rework/cleanup submitted: http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html - precise reserved memory mapping - more precise description - compatible string Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: nbg6817: sync MAC addresses to the upstream valuesStefan Lippers-Hollmann2017-11-032-2/+5
| | | | | | | | | | | | | | | | | | | | | | The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses are stored in the ART partition and the generated MAC addresses for the wlan interfaces alternate randomly between 12:34:56:78:90:12 and 00:03:7f:12:34:56. interface new/ OEM MAC old MAC wlan-2.4g (phy1): ethaddr undefined wlan-5g (phy0): ethaddr + 1 undefined lan : ethaddr + 2 ethaddr wan : ethaddr + 3 ethaddr + 1 This patch defines stable MAC addresses for the wlan interfaces for the first time instead of generating them at random. The previously defined values for lan/ wan are changed to follow the settings of the OEM firmware. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: Archer C2600: fix switch ports numberingBaptiste Jonglez2017-08-241-1/+4
| | | | | | | The order of LAN ports shown in Luci is reversed compared to what is written on the case of the device. Fix the order so that they match. Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* treewide: use only board_name function to get nameMathias Kresin2017-07-151-1/+1
| | | | | | | | | | | | Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree compatible string directly. Always use the board_name function to get the board name. The admswconfig package still reads /proc/cpuinfo directly. The code looks somehow broken and the whole adm5120 which uses this package looks unmaintained. Leave it as it is for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop target board_name functionsMathias Kresin2017-07-151-9/+0
| | | | | | They are not used any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: use the generic board_name functionMathias Kresin2017-07-156-18/+8
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: populate boardname and model earlierMathias Kresin2017-07-151-0/+0
| | | | | | | | | | | | | For targets using the generic board detection and board specific settings in diag.sh, the board name is still unset at the time the set_state() provided by diag.sh is called by 10_indicate_preinit. Change the execution order to ensure the boardname is populated before required the first time. Do the target specific board detection as early as possible, directly followed by the generic one to allow a seamless switch to the generic function for populating /tmp/sysinfo/. Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: automatically handle paths and symlinks for RAMFS_COPY_BINMatthias Schiffer2017-07-111-1/+1
| | | | | | | | | | | | Depending on busybox applet selection, paths of basic utiilties may differ, and may not work as symlinks to busybox. Simply using whatever binary is found in PATH and detecting symlinks automatically is more robust and easier to maintain. The list of binaries is also slightly cleaned up and duplicates are removed. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ipq806x: upgrade: fix RAMFS_COPY_*Matthias Schiffer2017-07-112-21/+5
| | | | | | | | | RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded linksys_preupgrade function is removed, and the nand_do_upgrade call is moved to platform_do_upgrade. Fixes: 30f61a34b4cf "base-files: always use staged sysupgrade" Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ipq806x: qca99xx: fix wifi calibrationPavel Kubelun2017-06-171-2/+2
| | | | | | | | | | As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine. Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin). Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 boardRam Chandra Jangir2017-06-071-0/+1
| | | | | | | | | | | | | | This change add IPQ40xx AP-DK04.1-C1 board image support, enables ubi image for IPQ40xx AP-DK04.1-C1 board and also add sysupgrage support for AP-DK04.1-C1 and generates a sysupgrade.tar image. Testing: *Tested on IPQ40xx AP-DK04.1-C1: a. NAND boot b. ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* treewide: fix device tree path in scriptsMathias Kresin2017-05-261-1/+1
| | | | | | | | The device tree is at /proc/device-tree/ without a base subdir. Fixes: da472e5b30f6 ("treewide: access device tree from userspace via /proc/") Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: access device tree from userspace via /proc/Mathias Kresin2017-05-261-1/+1
| | | | | | | Access the device tree via /proc/device-tree/ is the documented way to access the properties. Everything else might not work in future. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: fix EA8500 switch configurationJo-Philipp Wich2017-05-031-1/+1
| | | | | | | | | Do not assign the CPU port twice, this confuses LuCI and possible other programs relying on topology information in board.json. Ref: https://github.com/openwrt/luci/issues/1086 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: add ipq4019 fritz4040 supportChristian Lamparter2017-03-225-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx/ipq806x/mediatek/mvebu: fix network defaultsJo-Philipp Wich2017-02-071-1/+1
| | | | | | | | | | | After "73d923e base-files: emit tagged switch configuration by default" some default network configurations are broken because the lan and wan ifnames are forcibly set to untagged netdevs. Adjust the offending set_interfaces_lan_wan() calls to use the proper tagged device names. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: fix wireless macsHannu Nyman2017-02-031-1/+1
| | | | | | | | | | | | Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S D7800") added a trailing TAB char after the backslash which prevents the assignment of the correct MACs for wifi devices. Fixes: FS#451 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [reworded commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: Fix wireless support for Netgear Nighthawk X4S D7800Zhang Jingye2017-01-182-11/+15
| | | | | | | | | | D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band. However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading. This patch adds d7800 to ath10k caldata extraction list. I can get two functional wireless bands after making change to it. Signed-off-by: Zhang Jingye <934526987@qq.com>
* ipq806x: EA8500 fix sysupgrade over stock firmwareAdrian Panella2016-12-201-4/+26
| | | | | | | | | | When running sysupgrade for the first time over the second partition (that still had stock firmware) the rootfs wasn't flashed as there wasn't enough space. This happend because stock also uses UBI, but the volume name wasn't recognised and wasn't deleted before flashing. Signed-off-by: Adrian Panella <ianchi74@outlook.com>
* ipq806x: more dts cleanupMathias Kresin2016-11-271-19/+5
| | | | | | | | | | | | | | | | | | | | | | | Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this GPIO is mentioned in the GPL tarball, it doesn't do anything. The 2.4/5 GHz LEDs are connected to the wifi chips and not be controlled from the the userspace. Use the LEDs names/colours as they are used in the board manuals. Merge redundant LED configurations. Use the phy[0|1]tpt trigger for the wireless LEDs. Remove the workarounds for the not controllable wireless LEDs. Fix spi compatible strings and remove superfluous spi-max-frequency parameters. If there are two power leds, use one for indicating normal operation and one for failsafe/upgrade. Keep the on/off state of the main power led during boot. Use the usb pinmux settings from the nbg6817 gpl sources. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: clean up dts filesHenryk Heisig2016-11-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the pinmux to the values found in the GPL tarballs of the boards. Remove pinmux which are is not used (like nand pinmux for spi flash boards). This allows to use the wan orange led of the C2600 which had a wrong pinmux before. Might fix buttons or leds of other boards as well. Fix the LED color and the ledswitch key code of the C2600. Rename the ledgnr to ledswitch. Add support for indication the boot state using LEDs to the D7800, NBG6817, R7500 and R7500v2. Change GPIO active to readable values in D7800, EA8500, R7500, R7500v2 and R7800. Change gpioexport to gpio pinmux. Add proper "drive strenght" to i2c4_pins and use it for RPM on C2600, D7800, EA8500, R7500, R7500v2. Remove pcie pinmux from D7800. Move pinctrl to correct place in NBG6817 and R7800. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ipq806x: add support for TP-Link Archer VR2600vSebastian Quilitz2016-11-246-1/+26
| | | | | | | | | | | | | | | | | | This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
* ipq806x: c2600: change wan and lan led trigger to swconfig portHenryk Heisig2016-11-211-2/+2
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ipq806x: remove device specific sysupgrade image checksFelix Fietkau2016-11-201-24/+1
| | | | | | Replaced by image metadata Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: append metadata to imagesFelix Fietkau2016-11-191-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: fixes for R7800 and C2600Pavel Kubelun2016-11-161-3/+3
| | | | | | | | Updating spi pins configuration in R7800 and C2600 DTs Adding more usb power pin export and gsbi6 in R7800 DT Updating and fixing leds Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix leds, sata port for Netgear R7800 and minor fixes - renamed ↵Pavel Kubelun2016-11-031-2/+9
| | | | | | leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: TP-Link Archer C2600: convert old usbdev trigger to new usbportCezary Jackiewicz2016-11-031-2/+2
| | | | Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ipq806x/nbg6817: add sysupgrade supportAndré Valentin2016-10-262-0/+99
| | | | | | Add new way of flashing to mmc devices based on rootfs split with loop devices. Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq806x/nbg6817: add support for ZyXEL NBG6817André Valentin2016-10-264-0/+21
| | | | | | | | | | | | | | | | | CPU: 2x1.8GHz ARM, RAM: 512MiB Storage: 4MiB serial Flash, 3.9GiB MMC NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin to device. Then run: cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4 cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5 reboot -f For debugging serial console is easily visible on board, no soldering needed. Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq806x: C2600: change leds colour nameHenryk Heisig2016-10-151-5/+5
| | | | Signed-off-by: Henryk Heisig hyniu@o2.pl
* ipq806x: add support for indicating the boot and upgrade state using four ledsHenryk Heisig2016-10-153-12/+41
| | | | Signed-off-by: Henryk Heisig hyniu@o2.pl
* ipq806x: fix wlan mac for Netgear R7800Pavel Kubelun2016-10-061-0/+3
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
generated by cgit v1.1 at 2024-11-17 22:54:58 +0000