summaryrefslogtreecommitdiff
path: root/target/linux/mcs814x
Commit message (Expand)AuthorAgeFilesLines
* target: don't build jffs2 nor images by defaultJonas Gorski2013-06-051-1/+1
* Change default IPv6 config to enable DHCPv6-PDSteven Barth2013-04-221-1/+1
* Adapt default network configuration for IPv6Steven Barth2013-04-091-0/+8
* mcs814x: use devm_request_and_ioremap in mcs814x-rng driverFlorian Fainelli2013-03-171-8/+1
* mcs814x: use devm_request_and_ioremap helper for nuport_mac driverFlorian Fainelli2013-03-171-4/+2
* mcs814x: remove PCI codeFlorian Fainelli2013-03-176-484/+1
* mcs814x: implement MULTI_IRQ_HANDLERFlorian Fainelli2013-03-164-25/+24
* mcs814x: use the standard device tree binding to represent a PHY nodeFlorian Fainelli2013-03-164-3/+38
* all targets: use numerically prefixed uci-defaults file names to better contr...Jo-Philipp Wich2013-01-181-0/+0
* target: enable XZ BCJ decompressor code after r35097Florian Fainelli2013-01-141-0/+2
* do not call clk_put() on the timer clockFlorian Fainelli2012-11-271-1/+0
* do not list specific board compatible stringsFlorian Fainelli2012-11-271-2/+0
* remove unused variables from Makefile.bootFlorian Fainelli2012-11-271-2/+0
* nuport-mac: various fixesFlorian Fainelli2012-10-151-3/+5
* more convertions to {read,write}_relaxed I/O accessorsFlorian Fainelli2012-10-033-7/+7
* add wmbus-repeater to the dLAN USB Extender profileFlorian Fainelli2012-09-251-1/+2
* enable multicast and advanced ip routers configsFlorian Fainelli2012-09-251-2/+0
* add kmod-usb-serial-ftdi to the dLAN USB Extender profileFlorian Fainelli2012-09-251-1/+1
* generic: move GENERIC_PWM symbol into the generic configGabor Juhos2012-09-131-1/+0
* use the recommended ARM I/O accessorsFlorian Fainelli2012-09-089-52/+55
* add some ohci workarounds to make ohci workFlorian Fainelli2012-09-051-0/+64
* enable CFI command set 0002 FORCE_WORD_WRITEFlorian Fainelli2012-09-031-0/+14
* pad squashfs imageFlorian Fainelli2012-09-031-0/+4
* add Generic and dLAN USB Extender profilesFlorian Fainelli2012-09-033-3/+36
* nuport-mac: disable MAC RX and TX during interface closeFlorian Fainelli2012-09-031-0/+5
* MCS8140 actually selects CPU_ARM926TFlorian Fainelli2012-08-142-2/+2
* only support 128KiB erase block sizesFlorian Fainelli2012-08-111-0/+2
* disable PCI supportFlorian Fainelli2012-08-113-33/+5
* strip a bit more the kernel configFlorian Fainelli2012-08-111-24/+1
* properly advertise OHCI and EHCI capabilitiesFlorian Fainelli2012-08-111-1/+3
* change partition names to be more in line with other OpenWrt devicesFlorian Fainelli2012-08-111-4/+4
* generate upgrade files suffixed with filesystem typeFlorian Fainelli2012-08-111-3/+3
* nuport-mac: delay call to napi_start() until fully able to process RXFlorian Fainelli2012-08-101-2/+2
* set a compatible command-line to boot from flashFlorian Fainelli2012-08-101-1/+1
* nuport-mac: use dma_mapping_error() instead of checking pointersFlorian Fainelli2012-08-091-2/+2
* nuport-mac: rework PHY interrupt configuration to avoid racesFlorian Fainelli2012-08-081-7/+7
* nuport-mac: close possible race condition during startFlorian Fainelli2012-08-081-1/+5
* nuport-mac: unmap the DMA buffer when closing deviceFlorian Fainelli2012-08-081-0/+4
* nuport-mac: check dma_map_single address return valuesFlorian Fainelli2012-08-081-0/+4
* build a Devolo dLAN USB Extender specific imageFlorian Fainelli2012-08-081-1/+8
* cleanup image generationFlorian Fainelli2012-08-081-4/+8
* nuport-mac: properly protect the phy interrupt handlerFlorian Fainelli2012-08-021-2/+8
* add missing netmask to the network configFlorian Fainelli2012-08-011-0/+1
* assume the link is up and full-duplex by defaultFlorian Fainelli2012-08-011-2/+2
* add a default and suitable network config fileFlorian Fainelli2012-08-011-0/+12
* resync defconfig enable XZ compressionFlorian Fainelli2012-08-011-7/+1
* properly generate squashfs, jffs2 and initramfs images and kernelsFlorian Fainelli2012-07-312-16/+9
* set DEVICE_TYPE to other to avoid pulling unecessary packagesFlorian Fainelli2012-07-151-0/+2
* add compatible property to pci nodeFlorian Fainelli2012-07-151-0/+1
* use ohci_err() instead of err()Florian Fainelli2012-07-151-1/+1