summaryrefslogtreecommitdiff
path: root/target/linux/brcm63xx/patches-3.6/107-spi-bcm63xx-fix-multi-transfer-messages.patch
blob: 2da5044492d2a4024a8089a1325739713e5b642a (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
From 0f2ae1e1282ff64f74a5e36f7da874f94911225e Mon Sep 17 00:00:00 2001
From: Jonas Gorski <jonas.gorski@gmail.com>
Date: Wed, 14 Nov 2012 22:22:33 +0100
Subject: [PATCH] spi/bcm63xx: fix multi transfer messages

The BCM63XX SPI controller does not support keeping CS asserted after
sending its buffer. This breaks common usages like spi_write_then_read,
where it is expected to be kept active during the whole transfers.

Work around this by combining the transfers into one if the buffer
allows. For spi_write_then_read, use the prepend byte feature to write
to "prepend" the write if it is less than 15 bytes, allowing the whole
fifo size for the read.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
---
Tested on a SPI conntected switch which required keeping CS active between
the register read command and reading the register contents.

Based on Mark's spi/next.

Not sure if this is stable material, as it's quite invasive.

 drivers/spi/spi-bcm63xx.c |  172 ++++++++++++++++++++++++++++++---------------
 1 file changed, 117 insertions(+), 55 deletions(-)

--- a/drivers/spi/spi-bcm63xx.c
+++ b/drivers/spi/spi-bcm63xx.c
@@ -38,6 +38,8 @@
 #define PFX		KBUILD_MODNAME
 #define DRV_VER		"0.1.2"
 
+#define BCM63XX_SPI_MAX_PREPEND		15
+
 struct bcm63xx_spi {
 	struct completion	done;
 
@@ -50,16 +52,10 @@ struct bcm63xx_spi {
 	unsigned int		msg_type_shift;
 	unsigned int		msg_ctl_width;
 
-	/* Data buffers */
-	const unsigned char	*tx_ptr;
-	unsigned char		*rx_ptr;
-
 	/* data iomem */
 	u8 __iomem		*tx_io;
 	const u8 __iomem	*rx_io;
 
-	int			remaining_bytes;
-
 	struct clk		*clk;
 	struct platform_device	*pdev;
 };
@@ -184,50 +180,60 @@ static int bcm63xx_spi_setup(struct spi_
 	return 0;
 }
 
-/* Fill the TX FIFO with as many bytes as possible */
-static void bcm63xx_spi_fill_tx_fifo(struct bcm63xx_spi *bs)
-{
-	u8 size;
-
-	/* Fill the Tx FIFO with as many bytes as possible */
-	size = bs->remaining_bytes < bs->fifo_size ? bs->remaining_bytes :
-		bs->fifo_size;
-	memcpy_toio(bs->tx_io, bs->tx_ptr, size);
-	bs->remaining_bytes -= size;
-}
-
 static unsigned int bcm63xx_txrx_bufs(struct spi_device *spi,
-					struct spi_transfer *t)
+					struct spi_transfer *first,
+					unsigned int n_transfers)
 {
 	struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
 	u16 msg_ctl;
 	u16 cmd;
+	unsigned int i, timeout, total_len = 0, prepend_len = 0, len = 0;
+	struct spi_transfer *t = first;
+	u8 rx_tail;
+	bool do_rx = false;
+	bool do_tx = false;
 
 	/* Disable the CMD_DONE interrupt */
 	bcm_spi_writeb(bs, 0, SPI_INT_MASK);
 
-	dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
-		t->tx_buf, t->rx_buf, t->len);
+	if (n_transfers > 1 && t->tx_buf && t->len <= BCM63XX_SPI_MAX_PREPEND)
+		prepend_len = t->len;
+
+	/* prepare the buffer */
+	for (i = 0; i < n_transfers; i++) {
+		if (t->tx_buf) {
+			do_tx = true;
+			memcpy_toio(bs->tx_io + total_len, t->tx_buf, t->len);
+
+			/* don't prepend more than one tx */
+			if (t != first)
+				prepend_len = 0;
+		}
+
+		if (t->rx_buf) {
+			do_rx = true;
+			if (t == first)
+				prepend_len = 0;
+		}
 
-	/* Transmitter is inhibited */
-	bs->tx_ptr = t->tx_buf;
-	bs->rx_ptr = t->rx_buf;
-
-	if (t->tx_buf) {
-		bs->remaining_bytes = t->len;
-		bcm63xx_spi_fill_tx_fifo(bs);
+		total_len += t->len;
+
+		t = list_entry(t->transfer_list.next, struct spi_transfer,
+			       transfer_list);
 	}
 
+	len = total_len - prepend_len;
+
 	init_completion(&bs->done);
 
 	/* Fill in the Message control register */
-	msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT);
+	msg_ctl = (len << SPI_BYTE_CNT_SHIFT);
 
-	if (t->rx_buf && t->tx_buf)
+	if (do_rx && do_tx && prepend_len == 0)
 		msg_ctl |= (SPI_FD_RW << bs->msg_type_shift);
-	else if (t->rx_buf)
+	else if (do_rx)
 		msg_ctl |= (SPI_HD_R << bs->msg_type_shift);
-	else if (t->tx_buf)
+	else if (do_tx)
 		msg_ctl |= (SPI_HD_W << bs->msg_type_shift);
 
 	switch (bs->msg_ctl_width) {
@@ -241,14 +247,41 @@ static unsigned int bcm63xx_txrx_bufs(st
 
 	/* Issue the transfer */
 	cmd = SPI_CMD_START_IMMEDIATE;
-	cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
+	cmd |= (prepend_len << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
 	cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT);
 	bcm_spi_writew(bs, cmd, SPI_CMD);
 
 	/* Enable the CMD_DONE interrupt */
 	bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
 
-	return t->len - bs->remaining_bytes;
+	timeout = wait_for_completion_timeout(&bs->done, HZ);
+	if (!timeout)
+		return -ETIMEDOUT;
+
+	/* read out all data */
+	rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
+
+	if (do_rx && rx_tail != len)
+		return -EINVAL;
+
+	if (!rx_tail)
+		return total_len;
+
+	len = 0;
+	t = first;
+	/* Read out all the data */
+	for (i = 0; i < n_transfers; i++) {
+		if (t->rx_buf)
+			memcpy_fromio(t->rx_buf, bs->rx_io + len, t->len);
+
+		if (t != first || prepend_len == 0)
+			len += t->len;
+
+		t = list_entry(t->transfer_list.next, struct spi_transfer,
+			       transfer_list);
+	}
+
+	return total_len;
 }
 
 static int bcm63xx_spi_prepare_transfer(struct spi_master *master)
@@ -273,42 +306,71 @@ static int bcm63xx_spi_transfer_one(stru
 					struct spi_message *m)
 {
 	struct bcm63xx_spi *bs = spi_master_get_devdata(master);
-	struct spi_transfer *t;
+	struct spi_transfer *t, *first = NULL;
 	struct spi_device *spi = m->spi;
 	int status = 0;
-	unsigned int timeout = 0;
+	unsigned int n_transfers = 0, total_len = 0;
+	bool can_use_prepend = false;
 
+	/*
+	 * This SPI controller does not support keeping CS active after a
+	 * transfer, so we need to combine the transfers into one until we may
+	 * deassert CS.
+	 */
 	list_for_each_entry(t, &m->transfers, transfer_list) {
-		unsigned int len = t->len;
-		u8 rx_tail;
-
 		status = bcm63xx_spi_check_transfer(spi, t);
 		if (status < 0)
 			goto exit;
 
-		/* configure adapter for a new transfer */
-		bcm63xx_spi_setup_transfer(spi, t);
+		if (!first)
+			first = t;
 
-		while (len) {
-			/* send the data */
-			len -= bcm63xx_txrx_bufs(spi, t);
-
-			timeout = wait_for_completion_timeout(&bs->done, HZ);
-			if (!timeout) {
-				status = -ETIMEDOUT;
-				goto exit;
-			}
+		n_transfers++;
+		total_len += t->len;
+
+		if (n_transfers == 2 && !first->rx_buf && !t->tx_buf &&
+		    first->len <= BCM63XX_SPI_MAX_PREPEND)
+			can_use_prepend = true;
+		else if (can_use_prepend && t->tx_buf)
+			can_use_prepend = false;
+
+		if ((can_use_prepend &&
+		     total_len > (bs->fifo_size + BCM63XX_SPI_MAX_PREPEND)) ||
+		    (!can_use_prepend && total_len > bs->fifo_size)) {
+			status = -EINVAL;
+			goto exit;
+		}
 
-			/* read out all data */
-			rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
+		/* all transfers have to be made at the same speed */
+		if (t->speed_hz != first->speed_hz) {
+			status = -EINVAL;
+			goto exit;
+		}
 
-			/* Read out all the data */
-			if (rx_tail)
-				memcpy_fromio(bs->rx_ptr, bs->rx_io, rx_tail);
+		/* CS will be deasserted directly after the transfer */
+		if (t->delay_usecs) {
+			status = -EINVAL;
+			goto exit;
 		}
 
-		m->actual_length += t->len;
+		if (t->cs_change ||
+		    list_is_last(&t->transfer_list, &m->transfers)) {
+			/* configure adapter for a new transfer */
+			bcm63xx_spi_setup_transfer(spi, first);
+
+			status = bcm63xx_txrx_bufs(spi, first, n_transfers);
+			if (status < 0)
+				goto exit;
+
+			m->actual_length += status;
+			first = NULL;
+			status = 0;
+			n_transfers = 0;
+			total_len = 0;
+			can_use_prepend = false;
+		}
 	}
+
 exit:
 	m->status = status;
 	spi_finalize_current_message(master);